Installation Sheet

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
For Customer Service, please
contact the place of purchase.
AssemblyInstructions:8330-4, 4SF / 6, 6SF
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
BURN RISK! Please turn o power to the
xture before adjusting the angle of the
rings to avoid burns from the exposed bulbs.
CONNECTING THE WIRES
5.Attachthexture’swirestothepowersupplywiresfromthejunctionbox.
Connectblacktoblack(orsmooth);whitetowhite(orribbed);groundto
ground(greenorcopper).Twisttheendsofthewirepairstogether,thentwist
onawireconnector.Makesurealltwistsareinthesamedirection.Ifthereis
nogroundwire(greenorcopper)fromthejunctionbox,locategroundscrew
(E)onmountingstrap(A)andwrapthexture’sgroundwirearoundthegreen
groundscrew(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove
the old xture from the ceiling, including the old mounting strap.
1.Mountingstrap(A)containsseveralpairsofthreadedholes.Findthepair
ofholesthatmatchesthespacingoftheholesonthejunctionboxandyour
xture’scanopy.Testcanopy(G)onmountingstrap(A)toensurethatthe
backplatewillhangstraightandenoughofthethreadsofmountingscrews(B)
willbeexposedfordeconuts(F)tot.Placethextureaside.Pullthehouse
wiresthroughthecenterofmountingstrap(A).
2.Placemountingstrap(A)overthejunctionboxsothatmountingscrews(D)
maybeinserted.Securemountingstrap(A)tothejunctionboxwithmounting
screws(D)andascrewdriver.Tightenthescrewssecurely.
3.Spacer(N)androds(LandK)areonthexture’swires,butnotconnectedto
thexture.Forthesemi-ushinstallation,youmustremovetherodsfromthe
wires.Thentwisttoremovethepostthreadsfromthetipofswivel(M).
4.Pushthexture’swiresthroughspacer(N),swivel(M),andcanopy(G).Place
spacer(N)ontopost(R).Thentwistswivel(M)ofcanopy(G)ontopost(R).
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
FINISHING THE INSTALLATION
6.Placethexture’scanopy(G)overmountingstrap(A)sothattheholesinmountingstrap(A)lineupwiththeholesincanopy(G).
7.Threaddeconuts(F)ontotheexposedthreadsofmountingscrews(B)untilcanopy(G)issnugagainsttheceiling.
8.Installlightbulbsinsockets(I-notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
9. Please note that you can adjust the position of the light source/ring left or right along the center column using thumb screw (J).
Twist rings (H) up and down to change the look/conguration. See the Burn Risk and Important notes above.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
Semi-ush Installation
Important Note: To avoid snapping the
xture’s wires, do not fully twist the rings
more than 2 times in the same direction.
Instead twist the ring in the opposite
direction to achieve the look you desire.
I
J
A
G
N
D
B
C
D
E
F
G
N
M
O
H