Installation Guide

ManualsBrandsGolden Lighting Manualsceiling lightingGolden Lighting Two Light Down Lighting Dual Mount Ceiling Fixture from the Torbellino Collection

Circular strap 1ea

Mounting screws

8/32T*1-1/2"L

2ea Wire connectors 3ea

Hex nut 2ea Deco or Ball Nut 2ea Green screws 2ea

Canopy 1ea Canopy loop 1ea

Canopy loop

collar

1ea

Hex nut 1ea Mounting strap 1ea

Mounting screws

8/32T*1-1/4"L

4ea

Nipple 2ea Washer 1ea Chain 6 ft

Chain

connector

2ea Finial 1ea Bottom cap

1ea

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

Fixture Name: Torbellino 8106-SF CDB

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts

are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for

replacement parts.

PARTS LIST

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

FIXTURE ASSEMBLY INSTRUCTIONS

For Customer Service, contact the place of purchase to arrange for replacement parts.

NOTE

NSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

ASSEMBLING THE FIXTURE as Semi flush (Fig. 1)

1. Place the Circular Rim (I) over the Glass Shade (L).

2.Take the Nipple/threaded rod (G)and screw into fixture at (F).

Secure in place with hex nut (G).

3. Place the Metal Sleeve (J) and the Cap (K) onto the Nipple

(H), there should be at least 1/2" of threaded rod exposed

above the metal sleeve.

4. Place the Glass shade (L), over the nipple (H). The Nipple

(H) shall protrude through the bottom hole of the Glass shade

(L).

5. Slide the Rubber Washer (M) onto the Nipple(H).

6. Slide Bottom Cap (P) over Nipple (G) and thread the Finial

(M) until tight.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)

8106-SF CDB

Read and review installation instruction sheet before

assembling the fixture.

Fig 1

Summary of content (4 pages)

PAGE 1
PARTS & ASSEMBLY SHEET Fixture Name: Torbellino 8106-SF CDB This fixture assembled PO:__________ Date: ________ Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts. PARTS LIST Company Name:_______________________Co.
PAGE 2
PARTS & ASSEMBLY SHEET Fixture Name: Torbellino 8106-SF CDB ASSEMBLING THE FIXTURE as Chain hung (Fig.2) Fig 2 1. Remove the Circular strap from top of Fixture and replace the long mounting screws with two short screws to hold the Deco nuts (E) in place on the fixture Top cap (D). 2. Feed the fixture wires through the Top loop (D2) and pull the wires until taut. Then screw the Top Loop（D2） to the coupling on the top of fixture (D) until tight. 3.
PAGE 3
INSTALLATION INSTRUCTIONS Fixture Name: Torbellino 8106-SF CDB For Semi Flush / Convertible Light Fixture WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER. HANGING THE FIXTURE as Semi flush (Fig. 1) 1. Carefully remove the new fixture from the carton and the yellow bag that holds all your parts. Check that all parts are included as shown in the illustration and parts list. 2. Shut off power at the circuit breaker and remove the old fixture from ceiling, including the old mounting strap. 3.
PAGE 4
INSTALLATION INSTRUCTIONS Fixture Name: Torbellino 8106-SF CDB For Semi Flush / Convertible Light Fixture WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER. HANGING THE FIXTURE as Chain hung (Fig.1) Fig. 1 1. Carefully remove the new fixture from the carton and the yellow bag that holds all parts. Check that all parts are included JUNCTION BOX (CEILING) as shown in the illustration and parts list. 2.