Installation Guide

Assembly Instructions: 5926-SF (Saxon)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Please note that this xture can be installed as a semi-ush or as a pendant and includes two canopies.
The semi-ush canopy has screws on the sides. The pendant canopy has a large hole in the center.
Please decide how you would like to install the xture and choose the appropriate canopy and
instructions. For pendant installation, please follow the instructions below. For semi-ush installation,
ip the page and follow the instructions.
Remove all of the contents from the carton. See the important notes above. Shut o the power at the
circuit breaker and completely remove the old xture from the ceiling, including the old mounting strap.
From the parts bag remove the mounting strap assembly. One end of nipple (F) should be attached to
mounting strap (A) with washer (C) and hex nut (D) in place. The other end may have canopy loop (H)
attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver.
Tighten securely. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the
mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads
should be exposed, and the canopy loop collar should t snugly onto the canopy loop. Remove canopy
(G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn o the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact the
place of purchase.
FINISHING THE INSTALLATION
Push canopy (G), canopy mirror (G1) and canopy plate (G2) up to the ceiling. Slide canopy loop (H) and canopy loop collar (I) up beneath the canopy.
Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place.
Slide candle sleeves (Q) over the sockets. Install light bulbs (not provided) in accordance with the xture’s specications. Do not exceed the
maximum recommended wattage.
Your installation is complete. Turn on the power and test the xture.
ASSEMBLING THE FIXTURE
Attach top loop (L) to post (M) of top cap (N). One of connector rods (O) will house the
xture’s wires. Slide the xture’s wires through the rod and attach hook (P) to loop (S).
Hook the other end of the rod to top cap (N). Pull the xture’s wires through the top of
rod (O). Have an assistant hold top cap (N) up and attach the remaining connector rods
(O) to xture’s base (R) and top cap (N). By measuring, determine the correct number of
chain links needed for proper hanging height. If necessary, use a pair of pliers to open
and remove any excess chain. Attach chain connectors (K) to each end of chain (J) before
attaching one end of the chain connector/chain to top loop (L). Close the chain connector.
Connect the other chain connector (K) to canopy loop (H). Feed the xture’s wires up
through top loop (L) then through chain (J) (every three links or so). Pull the wires until
taut. Gently slide canopy loop collar (I) and canopy plate (G2), canopy mirror (G1), and
canopy (G) onto the chain/wire.
CONNECTING THE WIRES
Have an assistant support the xture’s weight while completing the wiring. Cut away excess
wire. Thread the xture’s wires through canopy loop and nipple. Attach the xture’s wires to
the power supply wires from the junction box. Connect black to smooth/black/transparent
(L) wire; white to ribbed/white/transparent (N) wire; ground to ground (green or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure
all twists are in the same direction. If there is no ground wire (green or copper) from the
junction box, locate ground screw (E) on mounting strap (A) and wrap the xture ground
wire around the green ground screw (E). Use a screwdriver to secure ground screw (E) onto
the mounting bracket/mounting strap. Tuck all wires.
PENDANT INSTALLATION
B
E
H
I
K
G
G1
G2
D
C
F
J
JUNCTION
BOX
L
A
M
N
S
P
O
Q
R