Instructions / Assembly

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
For Customer Service, please
contact the place of purchase.
AssemblyInstructions:3824-A1W
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
FINISHING THE INSTALLATION
5.Placebackplate(F)overmountingbracket(B).Insertsmallscrews(A)intothesideholesinbackplate(F)tosecureittomounting
bracket(B).Slideshade(I)oversocket(H)andsecureinplacewithsocketring(J).
6.Installalightbulb(notincluded)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
7.Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
8.Adjusttheaccordionlikefeatureoftheswingarm(C)asdesiredsuchasleft,right,closertothewall,orfurtheraway.
9.Pivotthelightsourcebytiltingthelampshadehead.Tolockthelightxturepositioninplacetightenthumbscrews.
10.Flipthewallswitchtoturnonandoffthexture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Remove the old xture from the wall, including
the old mounting bracket.
1.Mountingplate(N)isattachedtobackplate(F).Tobegin,removemountingplate(N)frombackplate(F).Placemountingbracket
(B)upagainstyourjunctionbox.Positionthemountingbracketsothattheholesonthesidearelevelandparallelwiththeoor.
2. Leaving at least 8 to 10 inches of cord for wiring, use a pair of wire cutters to trim the plug from cord (L). Pull the cord up
through the hole in the bottom of backplate (F) and plug the hole with stopper (P).
3.Pullthehousewiresfromthejunctionboxthroughthecenterofmountingbracket(B).Securemountingbracket(B)tothejunction
boxwithmountingscrews(D)andascrewdriver.Tightenthescrewssecurely.
CONNECTING THE WIRES
4.Striptheplasticcoverfrom1-2inchesofcord(L).Thexture’sgroundwireshouldbewrappedinsideofthebackplate(F).Unwrap
thegroundwire.Attachthexture’swirestothehousewirespulledearlierfromthejunctionbox.ConnectHottoHot(thisistheblack
wire,transparentwirewithblackinnerthread,orsmoothwire),NeutraltoNeutral(theneutralwireisthewhite,atransparentwirewith
whiteinnerthread,ortheribbedwire),andGroundtoGround(thegreenwire,transparentwirewithgreeninnerthread,orthecopper
wire).Twisttheendsofeachwirepairtogether.Secureeachconnectionwithawireconnector(usuallyorange).Makesurealltwists
areinthesamedirection.Ifthereisnohousegroundwirecomingfromthejunctionbox,pleaselocategroundscrew(E)onmounting
bracket(B)andwrapthexture’sgroundwirearoundgroundscrew(E).Useascrewdrivertotightenthetopofgroundscrew(E)onto
thewiresandintothemountingbracket/mountingbracket.Tuckthewiresintothejunctionbox.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
To Install Over an Existing Junction Box and Hardwire the Fixture...
This xture has multiple installation options. Before
beginning, please review these instructions carefully.
Thextureincludes
mountingplate(N)and
mountingbracket(B).
This installation uses
mounting bracket (B).
B
E
D
A
F
H
I
J
G
N
D
B
L
P
C
JUNCTION
BOX
G
N
D
B
N