Installation Sheet

Assembly Instructions: 1019-6 SF/9 SF
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Carefully remove the new xture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut
off power at the circuit breaker and remove old xture from wall, including the old mounting strap.
1. From the parts bag remove the mounting strap assembly. The mounting strap (A) should come with mounting screws (B) and be
attached to the canopy via screws (C). Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver.
Tighten securely. Pull house wires through the center of the mounting strap (A).
ASSEMBLING THE FIXTURE
2.Hookrods(Q-3/Q-4)ontotheringsfoundonxturebase(L).Liftxturering(T)uptothehangingrods(Q-3/Q-4)andconnectthe
bottomhooksofrods(Q-3/Q-4)ontotheinnerrings(V)onxturering(T).
CONNECTING THE WIRES
3.Haveanassistantavailabletosupportthextureweightofring(T)whilecompletingtheentirewiringprocess.Usingascrewdriver,
unscrewscrews(Y)frompanels(X)foundwithinplates(U)onxturering(T).Insidepanels(X),youwillndwireconnectors(W).Push
wire connectors (W) into wire connector (N) found on one of the rods (Q-3/Q-4) until you hear a click. You may need to rearrange
rodstoensurewireconnectorsarenearoneanotherforeasywiringconnection.Tucktheconnectedwiresonxturering(T)back
intopanels(X)andusescrews(Y)andascrewdrivertosecurewiresbackintothepanels(X).Untwistnial(P)fromthexture’sbase
(L).Onceunscrewed,pullcup(O)offoftheexposednipplefromthebottomofxturebase(L)toexposewireconnector(W).Take
the wire connector (N) from one of the rods (Q-3/Q-4) and push into wire connector (W) until you hear a click. Tuck the connected
wiresbeneaththexturebase(L)andpushcup(O)overthenipple,makingsuretheconnectedwiresaresecuredwithinthecup(O).
Securecup(O)withconnectedwires(W&N)insidetothexturebase(L)usingnial(P).Twistnial(P)ontothenippleuntilsecure.
Attachthexture’swirestothehousewireswhichwerepulledearlierfromthejunctionboxthroughthemountingstrap(A).Connect
black to black (transparent wire with black inner thread or smooth); white to white (transparent wire with white inner thread or ribbed);
groundtoground(green,transparentwirewithgreeninnerthread,orcopper).Twisttheendsofthewirepairstogether,andthen
twist on a wire connector. Make sure all twists are in the same direction. If there is no ground wire (green or copper) coming from the
junctionbox,locategroundscrew(E)onthemountingstrapandwrapthexture’sgroundwirearoundthegreengroundscrew(E).
Use a screwdriver to secure ground screw (E) onto the mounting bracket. Tuck all wires neatly into the junction box.
FINISHING THE INSTALLATION
4. Push the canopy up to the ceiling and use side screws (C) to secure the canopy to the mounting bracket.
Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedmaximumrecommendedwattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
T
W
N
A
JUNCTION
E
B
C
Q-3/Q-4
O
P
X
Y
W
U
V
L
N
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread