Manual

ManualsBrandsGOG ManualsPaintballeNMY

01 BARREL BLOCKER: Screw the barrel into the eNMEy

. Slide

the barrel blocker over the barrel and secure its cord as far back

on the eNMEy

body as possible, cinching for a tight t. The

barrel blocker is critical safety equipment - nearly as important as

goggles. The barrel blocker must be in use any time the marker

is stored or handled in an area where people or property are not

protected by paintball goggles or paintball eld netting.

02 AIR SYSTEM: The eNMEy

is compatible with both CO2 and

high pressure compressed air (HPA). Screw in style HPA systems

and CO2 tanks can be screwed directly into the Air System Adapter

on the bottom of the eNMEy

grip frame. For best performance

with CO2, use an anti-siphon tank or use a standard tank with

a remote hose. Screw the tank in slowly so that its valve opens

slowly, creating a gentle rise in pressure. NOTE: CO2 and HPA

tanks are sold empty and must be lled before use. When using

CO2, you may notice occasional bursts of gas released from the

top edge of the regulator. This is the normal function of the relief

valve protecting the eNMEy

from liquid CO2.

REV

Barrel_Blocker

SHEET 1 OF 1

UNLESS OTHERWISE SPECIFIED:

SCALE: 1:2

WEIGHT:

REV

DWG. NO.

SIZE

TITLE:

NAME

DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRIC

TOLERANCING PER:

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

ANGULAR: MACH

BEND

TWO PLACE DECIMAL

THREE PLACE DECIMAL

APPLICATION

USED ON

NEXT ASSY

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAME HERE>. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

<INSERT COMPANY NAME HERE> IS

PROHIBITED.

Never use oil or any petroleum based cleaner or lubricant in an

HPA system. Strictly follow manufacturer’s instructions.

03 LOADER/PAINT: Insert a paintball loader (not included) into

the eNMEy

feedneck. High-performance electronic loaders

allow for higher rates of re and minimal paint breakage. Align the

loader and tighten both its top and bottom clamps with a 7/64-

inch allen wrench. Do not ll the loader with paint until ready to re

at a paintball eld. Use of high-quality, fresh paintballs will result

in best performance.

04 SAFETY: The eNMEy

is equipped with a trigger-block safety.

Pressing the small button on the right side of the grip frame

switches the eNMEy

to “live” for re, exposing the red ring

on the larger button on the left side. Pressing the larger button

blocks the trigger in the “safe” position. Only switch the eNMEy

“live” when in an area that is safe to shoot paintballs. The Safety

should never be considered a replacement for the barrel blocker

or paintball eye protection.

05 VELOCITY: At the start

of each day’s use, the ring

velocity of the eNMEy

must be calibrated, to

account for variances in

paint and climate. Measuring

and adjusting velocity is a

critical safety procedure to

ensure that the eNMEy

ring at safe levels. While

wearing ASTM compliant paintball goggles, in an area where

all bystanders are protected, remove the barrel blocker and re

over a chronograph to measure velocity. Using a 5/32-inch allen

setup

wrench, adjust the eNMEy

’s vertical regulator for more or less

pressure, to raise or lower velocity. Turning clockwise increases

pressure, to raise velocity, while turning counter-clockwise

decreases pressure to lower velocity. After each adjustment take

2 or three shots to allow the pressure to stabilize, then check

again by ring over the chronograph. Adjust until the eNMEy

ring within limits for the eld where you are playing. For safety

reasons and to avoid internal damage, never adjust the eNMEy

to re at greater than 300 feet per second.

troubleshooting and storage

DE-GASING: Always unload and de-gas the eNMEy

for transport, storage or maintenance. In an area where it is safe to shoot

and while wearing paintball goggles (the chronograph area at a paintball eld is ideal) loosen the eNMEy

’s feedneck and remove

the hopper. Remove the CO2 or HPA tank. Fire in a safe direction until all of the gas pressure inside the marker has been released.

WARNING: If the eNMEy

is not de-gassed, its regulator may hold enough pressure to re 3 or more shots, even after the gas supply

has been removed.

TROUBLESHOOTING: The most common issues experienced with the eNMEy

are easily solved.

eNMEy

is leaking or shows inconsistent velocity:

• Disassemble and clean the bolt assemnly. Inspect all o-rings

and replace any that show signs of wear or damage. Re-

lubricate with GR33SE

and reassemble.

• If using CO2, especially in cold weather, an anti-siphon tank,

remote hose or upgrading to a compressed air system may

improve consistency.

• Use only fresh, good quality .68 caliber paintballs.

eNMEy

shows inconsistent accuracy:

• This can be caused by poor quality, out of round paint. Use

high-quality paintballs and store them in a sealed container

in a cool, dry place.

Gas ocasionaly leaks for a moment from regulator or valve:

• This is a normal venting function that occurs when liquid CO2

enters the marker (often from pointing downward while shooting)

and protects the low-pressure components from damage.

NOTE: The eNMEy

trigger will only feel responsive when the

marker is charged with gas. Do not pull hard on the trigger with

no gas supply attached, expecting to feel a “click” as excessive

force may cause internal damage.