080p HDMI CAT Extender with Loopout - 70m User's Guide P/N: HDExt70 G4-0116A
Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User’s Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, please email us at support@gofanco.com. For drivers/manuals download, please go to www.gofanco.com/ downloads.
• • • Shut off power and make sure environment is safe before installation Do not plug the HDMI cables and IR cables in/out when the device is in use to avoid cable damage. Make sure they are plugged into the correct ports Use the included DC5V power adapters only.
Introduction The 1080p HDMI CAT Extender with Loopout 70m extends HDMI transmission up to 70m (230ft) over CAT6/7. Features • • • • • • Supports up to 1080p@60Hz HDMI 1.3 and HDCP 1.4 compliant HDMI loop-out equipped on the TX, and bi-directional IR Supports 5.
Installation Requirements 1. 2. 3. HDMI source device (computer, DVD player, XBOX, PS3, etc) HDMI display device (SDTV/Monitor, HDTV/Monitor, projector, etc.
Product Layout Figure 1: Transmitter (TX) Layout 1. 2. 3. 4.
5. 6. 7. 8.
Figure 2: Receiver (RX) Layout 1. 2. 3. 4. 8 Reset: Resets the extender RJ45 In: Connects to the Transmitter's RJ45 Out using a CAT cable.
5. 6. 7. 8. Power/Signal LED: a) Flashing - RX is powered on with no HDMI signal detected; b) On - RX is powered on with HDMI signal detected Power Jack: Connects to the included power adapter Stereo Audio Out: Connect speakers, AVR, headphones, etc HDMI Out: Connects to your HDMI display CAT Cable Wiring We suggest both RJ-45 connectors be wired identically following T568B wiring standard for the best performance and compatibility.
Hardware Installation 1. 2. 3. 4. 5. 6. 10 Power off all devices including your HDMI source and HDMI display(s). Connect your HDMI source device to the Transmitter's HDMI In connector with an HDMI cable (HDMI cable not included). Optional: Connect a HDMI display to the Transmitter's HDMI Out connector with an HDMI cable (HDMI cable not included) for local monitoring of the HDMI signal. Optional: Connect the IR Blaster cable and IR Receiver cable. Face the IR eye towards your device's IR window.
7. 8. 9. Plug the included power adapters into the Transmitter's and Receiver's power jacks, then plug both power adapters into a reliable power source. Power on all connected devices. The HDMI extender is ready for use.
Connection Diagram Figure 3: IR Control - Source Device Figure 4: IR Control - Display Device 12
FAQ & Solutions Q: A: Q: A: Q: A: Q: A: There is no video output or audio and video display is not normal: 1) Press the reset button on both TX and RX. 2) Use a shorter network cable. The Receiver's Link LED is flashing: 1) Make sure the network cable follows the IEEE-568B wiring standard. 2) Check whether TX has HDMI signal input. 3) Reset the TX and reconnect. 4) Press the Reset button on the RX.
Specifications 14
Disclaimer The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted on the user’s guide. The pictures on the user’s guide are just for reference, and there may be some slight differences with the actual products. We reserve the right to make changes without prior notice to a product or system described herein to improve reliability, function, or design.
Thank you for choosing gofanco www.gofanco.
