TTL 无线引闪器 TTL Wireless Flash Trigger For Canon 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.
Contents 规格参数 可控从属单元组 GR 分组模式下，最多5组(A/B/C/D/E) Ratio光比分组模式下，3组(A/B/C) 传输范围(约) >100米 频道 32个 25 Foreword Multi Flash Settings (Times & Frequency) 26 Warning Multi Flash Settings (Output Value) 28 Names of Parts Group Settings Body LCD Panel Test Flash Modeling Lamp Control Accessories Setting GR Grouping Mode Battery Automatically Enter Power Saving Mode 其他 时延设置 有(0~10ms，以100us为单位设置) 无线快门 接收器端可以通过2.5mm同步接口控制相机拍摄 ZOOM设置 可以通过发射器调节闪灯焦距值 显示屏 宽屏液晶显示，背光开启或关闭 Installing Batteries C.
Foreword Warning Thanks for your purchase of this X1C TTL wireless flash trigger. Do not disassemble. Should repairs become necessary, this product must be This TTL wireless flash trigger can be used with a transmitter and one or more receivers for sent to an authorized maintenance center. studio flash, speedlite, and camera shutter. Featuring multi-channel triggering, stable signal Always keep this product dry. Do not use in rain or in damp conditions.
Names of Parts Names of Parts Body Receiver TEST Trigger Button Transmitter TEST Trigger Button --Half Press --Fully Press Battery Compartment AF Assist Beam Switch Battery Compartment --ON(AF Assist Beam outputs) --OFF(AF Assist Beam do not output) Micro USB Port Power Switch --ON (Power On) --OFF (Power Off) PC Sync Socket Hot Shoe Speedlite Connection Status Indicator Lamp Power Switch Micro USB Port --ON (Power On) --OFF (Power Off) 2.
Names of Parts Names of Parts Accessories Transmitter Panel CH 1.Remote Cable(C1, C3) E Gr D C B A 2.Sync Cable 3.
Using the Flash Trigger The flash trigger features the following functions: 1. As a Wireless Studio Flash Trigger 1.1 Mount the transmitter on camera hotshoe and turn it on before turning on the camera. 1.2 Connect the receiver to studio flash by Sync Cable (one end in 2.5mm Shutter Release Port of the receiver, the other end in sync port of studio flash) before turning on the studio flash. 1.3 Set the transmitter and the receiver to the same channel. 1.
Setting the Transmitter Setting the Transmitter Power Switch Mode Setting Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink. Note: In order to avoid power consumption, turn off the transmitter when not in use. 1. Short press the Button, and the mode of the current group will change. 2. To NON-GR grouping mode, all the groups’ modes will be changed simultaneously by the order of TTL/M/Multi, in accordance with Ratio flash mode.
Setting the Transmitter Setting the Transmitter Group Settings Multi Flash Settings (Times & Frequency) 1. Long press the Button to set all effective groups simultaneously. 1. In the multi flash (TTL and M icon are not displayed), long press the Button to enter multi flash setting submenu. 2. The two lines are separately displayed as T (flash times) and H (flash frequency). 3. Short press the Button to choose the related setting amounts.
Setting the Transmitter Setting the Transmitter Test Flash Automatically Enter Power Saving Mode 1. Press the Trigger Button to see the whether flash will fire normally or not. 2. Fully press the Trigger Button, and the Status Indicator Lamp turns red and the flash on the receive end can be triggered. 3. Use the transmitter to control camera to focus or shoot, and the transmitter is connecting to the camera (do not connect to the flash) now. 4.
Setting the Transmitter Custom Functions Setting Signs Settings and Description Setting the Transmitter Application Functions No. C.Fn-01 Custom Functions Setting Signs Single contact on mode It is advisable to set the transmitter to single √ C.Fn-08 contact mode when using it to trigger the flash Send the setting value forcibly -on by PC cord or through camera’s single contact. C.Fn-02 Zoom setting -AU OFF C.
Setting the Transmitter Wireless Shutter Release Mode Half press the Trigger Button to focus. Fully press the Trigger Button, and the Status Indicator Lamp turns red. Now camera is ready to shoot. When releasing the button, the Status Indicator Lamp turns off. Setting the Camera Use the External Flash Function on the camera to do the setting. Note: 1. GR mode can only be used normally when attaching to the CANON EOS cameras that issued after 2012.
Selecting the Operation Method Selecting the Operation Method Transmitter: Multi Mode (In the NON-GR Mode) X1C Operation Method 1(by default） Button TTL/M Mode (In the GR Mode or NON-GR Mode) Button CH/OK Function Short press (under normal status)Enter CH settings; (under settings)Confirm and back to Short press (under normal status) Enter CH settings; (under settings) Confirm and back Double-click Control the ON/OFF of modeling flash normal status Long press for Enter C.
Selecting the Operation Method Selecting the Operation Method Multi Mode (In the NON-GR Mode) X1C Operation Method 2 TTL/M Mode Button Operation Function Short press (under normal status) Enter CH settings; (under settings) Confirm and back Short press (under normal status) Enter CH settings; (under settings) Confirm and back to Double-click Control the ON/OFF of modeling flash Enter C.Fn custom settings Control the ON/OFF of modeling flash Long press for Long press for Enter C.
Selecting the Operation Method [Note 3] There are 5 groups only in the GR mode while 3 groups in other modes. Choose 3 or 5 groups by setting C.Fn-06 to 03 or 05. Receiver: Button Operation Function CH Short press Select the channel amount upwardly Double-click Select the channel amount downwardly Short press Select the group amount upwardly Double-click Select the group amount downwardly GR Caring for Flash Trigger Avoid sudden drops.
Technical Data Technical Data Model X1C Model X1C Type For Canon Type For Canon Compatible Cameras Canon EOS cameras (E-TTL II autoflash) Transmission range(approx.) >100m Support for the cameras that have PC sync socket. Channel 32 Builted-in remote system 2.4G Wireless Transmission Others Modulation mode MSK Synchronization delay set Yes (0~10ms, use 100us as the unit) Power supply 2*AA batteries Wireless shutter release Receiver can control camera shooting through 2.
