TTL 无线引闪器 TTL Wireless Flash Trigger For Canon 神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.
Contents 规格参数 可控从属单元组 GR 分组模式下，最多5组(A/B/C/D/E) Ratio光比分组模式下，3组(A/B/C) 传输范围(约) >100米 频道 32个 25 Foreword Multi Flash Settings (Times & Frequency) 26 For Your Safety Multi Flash Settings (Output Value) 28 Names of Parts Group Settings Body LCD Panel Test Flash Modeling Lamp Control Accessories Setting GR Grouping Mode Battery Automatically Enter Power Saving Mode 其他 时延设置 有(0~10ms，以100us为单位设置) 无线快门 接收器端可以通过2.
For Your Safety Foreword Thanks for your purchase of this X1C TTL wireless flash trigger. This TTL wireless flash trigger can be used with a transmitter and one or more receivers for studio flash, speedlite, and camera shutter. Featuring multi-channel triggering, stable signal transmission, and sensitive reaction, it gives photographers unparalleled flexibility and control over their strobist setups.
Names of Parts For Your Safety extremely high temperature. Failure to observe this precaution could result in fire or Body damage to the casing or internal parts. Transmitter Observe precautions when handling batteries TEST Trigger Button --Half Press --Fully Press Batteries may leak or explode if improperly handled. Observe the following precautions when handling batteries for use in this device: Use only batteries listed in this manual.
Names of Parts Names of Parts Transmitter Panel Receiver TEST Trigger Button CH E Gr D Battery Compartment C Power Switch Micro USB Port 2.
Names of Parts Using the Flash Trigger Accessories 1.Remote Cable(C1, C3) The flash trigger features the following functions: 2.Sync Cable 3.Sync Adapter Battery Installing Batteries As shown in the illustration, slide the battery compartment lid of the transmitter and receiver and insert two AA batteries (sold separately) separately. Low Battery Indication When the battery power (2 AA batteries <2.0V) gets low, Status Indicator Lamp blinks quickly (blink cycle=0.5s).
Using the Flash Trigger 3. As a Wired Shutter Release 3.1 Connect the receiver and the camera by Remote Cable (one end in receiver’s Shutter Release Port, the other end in camera’s shutter port) before turning on the camera. 3.2 Half press the Trigger Button to focus. When fully press the Trigger Button to shoot, the Status Indicator Lamp will turn red until releasing the button. 4. As a Wireless Studio Flash Trigger or Speedlite Trigger with PC Sync Socket 4.
Setting the Transmitter Setting the Transmitter Mode Setting Multi Flash Settings (Times & Frequency) 1. Short press the Button, and the mode of the current group will change. 2. To NON-GR grouping mode, all the groups’ modes will be changed simultaneously by the order of TTL/M/Multi, in accordance with Ratio flash mode. To GR grouping mode, only the current group’s mode will be changed by the order of TTL/M/--. CH Gr Current Group Settings 1.
Setting the Transmitter Setting the Transmitter Group Settings Test Flash 1. Long press the Button to set all effective groups simultaneously. 1. Press the Trigger Button to see the whether flash will fire normally or not. 2. Fully press the Trigger Button, and the Status Indicator Lamp turns red and the flash on the receive end can be triggered. 3.
Setting the Transmitter Setting the Transmitter Automatically Enter Power Saving Mode Custom 1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and the displays on the LCD panel will disappear. 2. Press any of the button ( fully pressed///) can wake up the flash trigger. If the transmitter is attached to the CANON EOS camera, half press the shutter can also wake up the system. 3.
Setting the Transmitter Setting the Transmitter Custom Functions Setting Signs Settings and Description Application C.Fn-08 Mandatory send the setting value ON/OFF -on After the setting value were changed, it will send the setting value. It will send the setting value mandatory before the trigger flash, although the setting value have no change. √ Setting the Camera Double-click the CH Button to turn on/off the modeling lamp of the receive end.
Setting the Receiver 4. The channel amount will increase from 1 to 32. When the current channel is 32, press the Button again and the channel 1 will be displayed on the panel. Selecting the Operation Method Transmitter: X1C Operation Method 1(by default） TTL/M Mode (In the GR Mode or NON-GR Mode) Group Settings Button 1. Short press the Button and the group amount will increase a step each time. 2. Long press the Button will enter quicker adjustment mode.
Selecting the Operation Method Selecting the Operation Method Multi Mode (In the NON-GR Mode) Button Operation Function Short press (under normal status) Enter CH settings; (under settings) Confirm and back X1C Operation Method 2 TTL/M Mode Button to normal status CH/OK Double-click Control the ON/OFF of modeling flash Long press for Enter C.
Selecting the Operation Method Selecting the Operation Method [Note 3] There are 5 groups only in the GR mode while 3 groups in other modes. Multi Mode (In the NON-GR Mode) Button Choose 3 or 5 groups by setting C.Fn-06 to 03 or 05. Operation Function Short press (under normal status) Enter CH settings; (under settings) Confirm and back to normal status CH/OK Double-click Control the ON/OFF of modeling flash Long press for Enter C.
Caring for Flash Trigger Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess stress. Keep dry. The product isn't water-proof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity. Avoid sudden temperature changes. Condensation happens if sudden temperature changes such as the circumstance when taking the transceiver out of a building with higher temperature to outside in winter.
Technical Data Compatible Camera Models Model X1C Canon EOS SLR Digital Cameras: Type For Canon 1Dx Mark II, 1Dx, 5Ds/5Dsr, 5D Mark III, 5D Mark II, 5D, 7D Mark II, 6D, 7D, Transmission range(approx.
