N= ASSEMBLY INSTRUCTION SKU CODE: (WF197563/WF197564/WF 199420) This set is included 3 boxes if don't receive full 3 boxes please contact our customer service team TRE WAM | SAFETY WARNINGS Follow the information on the warning label appearing on the upper bunk end structure and on the carton... Do not remove warning label from bed. Amway use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
Hardware List Co—o Assembly Tools Required (Not Included) Screws 1/4" x100 Steel Bracket PCs 4pc Wood Screws PCs 210 x40 mm Screws 1/4" x50 21/4" x 80 mm Wood dowel PCs PCs Hex-Head bolts PCs 21/4" 21/4" x 30 mm Horizontal-Hole bolts PCs Wood Screws PCs Hex-Head bolts PCs Screws 1/4" x70 21/4" x 25 mm PCs Allen Key 1pc Hex-Head bolts PCs 21/4" x 15 mm 212 x 110 Canopy head though -PCs Wood dowel PCs Wood Screws PCs Bracket Wood dowel 22pcs PCS 06/27
STE P 1 = Following below illustration Assembly Bottom beds Headboard and Foot board. Using hardware #1 connect A1 1 and A2 legs with B1 Frame to complete LEFT side of Bottom Bed.
1 4x2pcs Following below illustration Assembly Center bed's Headboard and Foot board. Using hardware #1 connect STEP 2-1: |A3 and A4 legs with B2 Frame to complete LEFT side of Center Bed.
PCs) PCs) 2 hollowing below illustration. . Using hardware #3 connect Steel with Uncomplicated On Step 2-1). STEP 2-2: .
1 JA7 and AB legs with B2 Frame to complete LEFT side of Upper Bed. Using hardware #1 connect A7 and AB legs with B4 Frame to STE Following below illustration Assembly Upper bed's Headboard and Foot board.
FN PCs PCs PCs follow detail view to Assembly Bottom bed's Headboard and Foot board with sidewall Following below Illustration Using hardware #6 #7 and dowel #4 at detail view for more detail 13/27 Inside Side Rail View
Following below Illustration . Using hardware #12#13 connect Frame(completed on Step 8) [Frame(completed on step 8) Put Support Slat (D2) on Bracket 13 12 PCs) PCs) STE Following below illustration: -Assembly 10 slats (D1) using hardware #8.
re PCs [Using hardware #9 to connect bed (completed on step 11) with Ladder (completed on step 4) STEP 1 2: Following below Illustration: 18/27
(pcs) STE Following below illustration Using hardware #6 #7 #10 -Put Support Sat (D2) on Bracket -Assembly 10 slats (D1) using hardware #8.
re PCs [Using hardware #9 to connect bed (completed on step 14) with Ladder (completed on step 4) STEP 15: Following below illustration: 21/27
FN FN PCs < PCs [od PCs) (5d “1 14 Lay the Upper Bed (completed on step 15) on Bed (completed on step 18) using the Dowel #14 and Dowel #4. [Then use Screw #3, #15 to permanent fix Canter and Upper Bad STEP 1 7: Following below Illustration. Wa NAT Lh OR A SAN {ANA CAN ON TW 7A SYN ZA XN VAN a .
re [Using hardware #9 to connect bed (completed on step 17) with Ladder (completed on step 4) STEP 18: Following below illustration: ATT] ALT 24/27
STE P 1 9-3 choir below alliteration Using hardware #5,Dowel 18 to Assembly Siide. Look at detail view for more detail STE P 1 9-4 suing below illustration Using hardware #3 #17 to Assembly Slide.
STE P 2 Orion below Illustration Using hardware #3 to Assembly Slide with Bed. 3 Look at de view for detail ook at detail view for more fetal P.
