ASSEMBLY INSTRUCTIONS CORNER TWIN BUNDBED WF196065/196066/196067 1
Detail View J D A J I F I 15 C L L H D E D B F 15 D O M O N O O E G K K 15 D A 15 H A D G V U T S B V R P Q R R S Ghi chú : Bước 2: 1 lắp LắpAA&&DD&&BC 2
Part List A B C Right leg-3pcs Right leg-2pcs Middle leg-1pc D E F Frame side-6pcs Front side rail (left)-2pcs Back side rail (left)-2pcs G H I Front side rail (right)-2pcs Back side rail (right)-2pcs Front guard rail(left)-2pcs J K L Back guard rail (left)-2pcs Front guard rail(right)-2pcs Back guard rail (right)-2pcs M N O Short right ladder post-1pc Long left ladder post-1pc P R Q Drawer front-1pc Drawer back-1pc T S Drawer side-2pcs V Drawer bottom rail-3pcs U Drawe
Hardware List 1 2 Ø10 x 30mm Wood dowel (90pcs) 3 Ø8 x 30mm Wood dowel (12pcs) 5 4 (Ø15)1/4" x 65mm Bolts (4pcs) 7 6 Ø1/4" x 100mm Hex-Head bolts (24pcs) 8 Ø1/4" x 30mm Hex-Head bolts (2pcs) 10 Ø1/4" x 50mm Hex-Head bolts (12pcs) 9 1/4"*15 (9.
STEP 1: Following below illustration Assembly FRAME #1 (x2). Using hardware #5 & #1 connect A and B legs with D Frame to complete FRAME #1 (x2) 1 16PCS 5 16PCS 1 5 B D D A FRAME #1(x2): STEP 2: Following below illustration Assembly FRAME #2.
STEP 3: Following below illustration Assembly LEFT BUNKBED. Using 1 3 8 hardware #3, #8 & #1 connect FRAME#1 and FRAME#3 with PART J (x2), Fx2 I(x2), E(x2). 24PCS 24PCS 24PCS FRAME #2: J FRAME #1: J F I 8 I E 8 1 1 8 F E 1 3 12 STEP 4: Following below illustration Assembly STAIRCASE.
STEP 5: Following below illustration Assembly STAIRCASE with SIDERAIL G (x2).
STEP 6 : Following below illustration Assembly LEFT BUNK BED Completed on Step 3) with RIGHT BUNK BED). Using hardware #8, #1 & #3 to connect Guardrail L(x2) & K (x2), Side Rail H(x2), STAIRCASE GROUP (Completed on Step 5) with FRAME# 1 (Completed on Step 1). Using hardware #8, #1, #3 & #4 to connect COMPLETED GROUP (on above step) with LEFT BUNK BED.
STEP 9: Following below illustration Assembly DRAWER. Connect part R (x3) with 10 2 part Q and part P by using hardware #2. Use hardware #10 to fix all part together. 12PCS 6PCS Q R R P R 2 2 10 STEP 10: Following below illustration Assembly DRAWER.
STEP 11: Following below illustration Assembly DRAWER. Using Screw #9 to screw Hardware #11 to bottom of Panel S Then use Screw #10 to connect part S with Drawer Frame (completed on Step 9) V U V T STEP 12: Following below illustration COMPLETED BED. 10 Using Screw #10(x80) to screw ALL Slat 15 on all the bed Then Push the DRAWER into under of RIGHT BUNK BED WARNING !: PLEASE COMPLETED SCREW ALL THE SLAT IN TO SIDE RAIL BEFORE USING.
