Installation Guide

ManualsBrandsGoBidet ManualsBathBidet Attachment in Chrome

FIG. 1

Product Detail

Placement on Toilet

Side View

Spray Arm Operation

Retract Extend

HOW TO INSTALL YOUR GoBidet™ 2003

Remove Toilet Seat. Fig 1.

1. Turn o water supply to toilet at Shut-o Valve (A).

.retaw lla yt pme ot telio t hs ulF .2

3. Disconnect Water Supply Line (B) from the toilet tank.

Note: Water may leak from toilet when water supply line is removed.

4. Loosen Nuts holding Toilet Seat (C) in place on underside of bowl.

Remove Toilet Seat and clean top of toilet bowl. Save seat mounting

parts for re-use.

Tools Needed:

Pliers, Slot Head Screwdriver, 5/64” Allen Wrench, Adjustable Wrench or 7/16”, 1/2”, 9/16”, 5/8”, 3/4” Combination Wrenches as

required, Silicone Grease

Note: To avoid damaging nish during installation of this product, do not use Adjustable Pliers for assembly. Use Adjustable

Wrench or a Combination Wrench as needed.

GoBidet Assembly

Note: If installing on a one-piece toilet, rst swap

the location of the Plastic Cap (D) and Mounting

Bracket Bushing (E). Tighten Bushing with Pliers.

If installing on a two-piece toilet, this step is not

necessary.

t ekcarB gn itnuoM morf ) F( tuN xeH daerh tnU .5

Bushing and remove Plastic Washer (G) and

Rubber Washer (H).

6. Loosen Hex Nut (I) securing Mounting Bracket

(J) to Water Control Valve (K).

7. Place Mounting Bracket (J) on Toilet with Spray

Arm Assembly (L) positioned over the bowl rim.

Insert Mounting Bracket Bushing (E) into left

hole. On the underside of bowl, install the

Rubber Washer (H) rst. Place the Plastic

Washer (G) on next and secure with Hex Nut (F).

Do not tighten completely.

8. Fully extend Spray Arm (M) by pulling Control

Knob (N). Adjust placement of Mounting Bracket

(J) and Water Control Valve (K) so Spray Head

(O) is in center of bowl. Now retract Spray Arm

(M) fully by pulling Control Knob (N) backward

to ensure it rests just beneath left side of bowl

rim. When positioned correctly, tighten Hex Nut

(I) that secures the Mounting Bracket (J) to the

Water Control Valve (K).

9. Fully tighten Hex Nut (F) on underside of

Mounting Bracket (J). Do not overtighten.

Summary of content (2 pages)

PAGE 1
HOW TO INSTALL YOUR GoBidet™ 2003 Tools Needed: Pliers, Slot Head Screwdriver, 5/64” Allen Wrench, Adjustable Wrench or 7/16”, 1/2”, 9/16”, 5/8”, 3/4” Combination Wrenches as required, Silicone Grease Note: To avoid damaging nish during installation of this product, do not use Adjustable Pliers for assembly. Use Adjustable Wrench or a Combination Wrench as needed. FIG. 1 Remove Toilet Seat. Fig 1. 1. Turn o water supply to toilet at Shut-o Valve (A). 2. Flus h toilet to empty all water. 3.
PAGE 2
HOW TO INSTALL YOUR GoBidet™ 2003 Connect Water Supply 10. Install “T-valve” (P) to the toilet. 11. Connect one end of Bidet Supply Line (Q) to the Cold Water Inlet (R) on the Water Control Valve (K). Tighten with wrench. Do not overtighten. 12. Connect the other end of the Bidet Supply Line (Q) to the “T-valve” (P). Tighten with wrench. Do not overtighten. T-valve installation location P 13. Check to ensure Water Control Valve (K) is in o position. 14. Turn on water supply to toilet at Shut-o Valve (A).