Full Product Manual

ManualsBrandsGoBidet ManualsBathBidet Attachment in Chrome

151 Ruths Place #5

Sequim, WA 98382

MODEL #2003C

In this box:

GoBidet Bidet Attachment

Tel 1-800-681-0753 • Fax +1 360-681-4029

www.Go-Bidet.com

• 1 User Manual

• 1 GoBidet™ Unit w/ mounting bracket, nut, rubber washer, and plastic washer

• 1 Plastic Spacer (part no. 2003.11)

• 1 3/8” Hose (part no. 2003.14)

• 1 7/8” T-valve (part no. 2003.18) - installs on bottom of toilet

tank

• Teon Tape

GoBidet Model GB-2003C

Limited Warranty

Used with normal care, this bidet product is guaranteed against defects

in material and workmanship for a period of one year. This warranty

does not cover improper installation or improper use. For complete

details, contact the dealer from where it was purchased or you may

reach us at:

www.Go-Bidet.com

1-800-681-0753

Summary of content (5 pages)

PAGE 1
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 • Fax +1 360-681-4029 www.Go-Bidet.com MODEL #2003C In this box: • 1 User Manual • 1 GoBidet™ Unit w/ mounting bracket, nut, rubber washer, and plastic washer • 1 Plastic Spacer (part no. 2003.11) • 1 3/8” Hose (part no. 2003.14) • 1 7/8” T-valve (part no. 2003.
PAGE 2
INSTALLATION INSTRUCTIONS & IMPORTANT NOTES This unit can accommodate hot and/or cold water installations. For cold water only, install as directed. For hot water installation, please use the Hot Water Installation Kit (Part no. 2003HIK ), available by calling 1-800-681-0753. Your GoBidet™ will attach to a one-piece toilet (tank/bowl are molded into one piece) or a two-piece toilet (tank/bowl are separate). It also fits regular (round) or elongated toilets.
PAGE 3
C. Hose Installation 1. Remember to use Teflon tape on all water line connections. 2. Install the 7/8” T (Part no 2003.18) to the bottom of the toilet. 3. Connect the 3/8” hose to the 3/8” nipple and then connect to the bidet. 4. Connect the other end of the hose to the already installed 7/8” T valve. 5. Dry your work area completely. Turn on water supply. 6. Check for leaks. D. Final Installation Instructions 1. If no leaks are found, re-install your toilet seat using existing bolts and nuts.
PAGE 4
G. Troubleshooting Removal of toilet seat is usually easily done by popping open the plastic screw covers behind the seat using a flathead screwdriver and unscrewing. If screws are corroded metal and not plastic, they may be difficult to remove using a traditional screwdriver. In this case, you should use a hacksaw blade or bolt cutter to remove screws from the toilet. Be sure to protect your toilet from damage if a hacksaw is used. 1.
PAGE 5
Rev. 20150810 2003.18 2003.14 2003.17 2003.11 B. COMO INSTALAR EL Two-Piece Toilet 2003.06 2003.07 2003.08 2003.09 2003.16 T-valve 2003.06 2003.07 T-valve installation location 2003.05 2003.10 2003.15 2003.13 2003.20 2003.01 One-Piece Toilet 2003.12 2003.02 D. INSTRUCCIONES FINALES FOR INDIVIDUAL PARTS CALL 1-888-670-9389 MODEL 2003 • Completed Assembly 2003.03 2003.45 2003.24 2003.19 2003.04 Swap location of plastic cap and threaded nut/bushing to position shown.