Owners manual

ManualsBrandsGO RHINO ManualsAutomotiveGo Rhino 24169T BR10 Front Replacement Bumper

REV. DATE: 3/17/2016 Page 1 of 6

Parts List

Item

Qty.

Part #

Description

Item

Qty.

Part #

Description

Torque

Bumper Replacement Shell

½” x 1 ½” Hex Bolt

64 ft. lbs.

Driver Frame Bracket

½” x 1 ½” Carriage Bolt

64 ft. lbs.

Passenger Frame Bracket

½” Flat Washer

Driver Auxiliary Bracket

½” Lock Washer

Passenger Auxiliary Bracket

½” Hex Nut

Driver Support Bracket

3/8” x 1 ¼” Hex Bolt

26 ft. lbs.

Passenger Support Bracket

3/8” Lock Washer

Driver Vent Cover

3/8” Flat Washer

Passenger Vent Cover

3/8” Hex Nut

Winch Cover

¼” x ¾” Button Head Bolt

71 in. lbs.

Light Pod Plate

¼” Nylon Lock Nut

License Plate Bracket

Hole Plug

Required for Installation (Sold Separately)

24273TW

Mounting Plate/Winch Tray

Installation Instructions

BR10 Front Bumper Replacement Part Number 24169T

2011-2014 Chevrolet Silverado 2500HD & 3500HD 2/4WD

Do not attempt to install this product on any vehicle other than the one listed above!

DAKAR PRO Brackets Part

# 524765

2014 Chevrolet Silverado 1500 2/4WD

Do not attempt to install this product on any vehicle other than the one listed above!

ILLUSTRATION #1

Summary of content (6 pages)

PAGE 1
Installation Instructions BR10 Front Bumper Replacement Part Number 24169T 2011-2014 Chevrolet Silverado 2500HD & 3500HD 2/4WD Do not attempt to install this product on any vehicle other than the one listed above! Parts List Part # Description Item Qty. Part # Description Torque DAKAR PRO Brackets Part Item Qty. 1 1 Bumper Replacement Shell 64 ft. lbs. 2 1 Driver Frame Bracket 64 ft. lbs.
PAGE 2
Tool Required: 10mm, 15mm, 18mm, 21mm, 7/16”, 9/16” & 3/4” Sockets 18mm, 7/16”, 9/16” & 3/4” Wrenches Slotted Blade Screw Driver 5/32” Hex Key Ratchet, Ratchet Extensions & Swivel Joint Adapter Approximate installation time: 2 hrs. IMPORTANT INSTALLATION NOTES AND SUGGESTIONS The pre-installed Mesh Winch and Vent Covers need to be removed using hand tools to slowly remove the bolts. Using an air assisted impact or ratchet will damage the bolt threads and the internal nut assembly in the bumper shell.
PAGE 3
Step-3 If equipped, disconnect the wiring harness from each of the fog lights, (Photo 3). Step-4 Remove the bolts (3) per side securing the outer bumper support bar to the body mount bracket and to the bumper using a 15mm socket and ratchet, (Photo 4). #3 Driver Side #4 Driver Side Step-5 Remove the nut and bolts’ securing each of the tow hooks to the frame using an 18mm wrench, socket, and ratchet, (Photo 5). Pull the hooks out from the front and remove from the vehicle.
PAGE 4
Bumper Replacement Installation Step-1 Install the driver’s side frame bracket by positioning the bracket over the frame, align the holes and secure the bracket to the frame using the factory paired bolts and nuts, (Photo 1). Leave the nuts and bolts loose for final adjustment. Repeat this step to install the passenger side frame bracket.
PAGE 5
Step-4 Center the mounting plate/winch tray with the vehicle then tighten the nuts and bolts securing the auxiliary brackets to the frame. Finger tighten all factory and supplied nuts and bolts securing the mounting plate/winch tray and frame brackets. If you are installing a winch, place the winch in the winch tray and refer to the winch manufacturer’s instructions for installation. Do not install the fairlead at this time.
PAGE 6
If installing a winch, install the roller fairlead to the bumper shell at this time. Refer to the winch manufacturer’s instructions for installation. If installing an optional light bar, install the light bar to the bumper replacement at this time. Refer to the light bar instructions for installation. Step-9 Install the winch cover and driver and passenger side front vent covers to the bumper shell using the supplied ¼” x ¾” button head bolts, (Photo 9 & 10).