PURE SINE WAVE INVERTER REMOTE User Manual GP-ISW-R (12/24) ® 15 14 gpelectric.com 13 12 11 10 GP-ISW-R © 2021 Go Power! Worldwide Technical Support and Product Information gpelectric.com Go Power! | Dometic 201-710 Redbrick Street Victoria, BC, V8T 5J3 Tel: 1.866.247.
CONTENTS 2. 2. FEATURES ����������������������������������������������������������������������������������������������������������2 3. SPECIFICATION ��������������������������������������������������������������������������������������������������2 4. INTRODUCTION �������������������������������������������������������������������������������������������������3 4.1 FRONT PANEL INTRODUCTION ������������������������������������������������������������3 4.
4. INTRODUCTION 4.1 FRONT PANEL INTRODUCTION 3 2 ® 15 gpelectric.com 14 13 12 11 GP-ISW-R-12 10 1 4 1 Note: the 24 volt inverter remote’s Battery voltage indicator reads “20, 22, 24, 26, 28, 30.” 1 Power ON/OFF button 3 Battery voltage indicator 2 Output power indicator 4 Other indicators POWER ON/OFF BUTTON Power ON/OFF button turns the inverter on or off. 2 OUTPUT POWER INDICATOR Output power indicator shows the power draw from the inverter by the load.
INTRODUCTION 3 BATTERY VOLTAGE INDICATOR Battery voltage indicator will move up and down as the battery voltage changes. Ideally, the voltage should remain in the green area of the bar chart. If the voltage goes into the red area at the top and bottom of the bar chart, the inverter may shut down. 4 OTHER INDICATORS • OVP (Over voltage protection): • Indicates that the inverter will shut down because its input voltage is above the voltage limit.
INTRODUCTION 4.2 REAR PANEL INTRODUCTION 89 Connector AUX 76 72 5 6.5 10±0.5 22±1.0 6 10.5 77 Ø4.5 7 5 5 AUX port 6 Phone jack connector Ø4.5±0.3 7 JP1 AUX PORT Note: the AUX port is only used in work trucks. The connector (shown above) attached to AUX wire (AWG 14 or 16) must be connected with a 12V / 0.5A fuse. • Ignition Lockout function: Turns OFF the inverter when the auxiliary input wiring is connected to the ACC with 12 volts.
INTRODUCTION PHONE JACK CONNECTOR Before connecting, make sure to switch the inverter to REMOTE mode. 2. Connect the RJ-11 cable between the ISW-R remote and the inverter. 6 6 1 1 A WIRE COLOR B 6 BLUE 6 5 YELLOW 5 4 GREEN 4 3 RED 3 2 BLACK 2 1 WHITE 1 9.6±0.2 9.6±0.2 A 12.4±0.3 3.1±0.2 14.6±0.3 14.6±0.3 6.5±0.2 12.4±0.3 6.5±0.2 1. 3.1±0.2 6 WARNING! DO NOT use a standard telephone cable. [page 6] | gpelectric.
INTRODUCTION 7 JP1 The JP1 is to set either the Return Override function or the Ignition Lockout function. • JP1 jumper “Short” - Return Override function: • Turns ON the inverter when the auxiliary input wiring is connected to the reversed gear shift with 12 volts. • JP1 jumper “Open” - Ignition Lockout function: • Turns OFF the inverter when the auxiliary input wiring is connected to the ACC with 12 volts. • The connector which is connected to AUX power must be used with a 12V / 0.5A fuse.
© 2021 Go Power! Worldwide Technical Support and Product Information gpelectric.com Go Power! | Dometic 201-710 Redbrick Street Victoria, BC, V8T 5J3 Tel: 1.866.247.
