About My Go-Ped® Model _______________________ Serial # _______________________ Motor _______________________ Motor Serial # _______________________ Gas:Oil Ratio _______________________ Dealer Service Center _______________________
WHAT WE GUARANTEE AND WHAT YOU PROMISE US Patmont Motor Werks, a Nevada Corporation (hereinafter referred to as “P.M.W.”) expressly warrants that each of its products is free from defects in material and workmanship under normal operating conditions and according to proper use for a period of 90 days from the date of original purchase. Frame and fork guaranteed for 2 years against factory defects and workmanship.
9.4 Suspension: Contents Section 1: Important Information Section 6: Starting • Although your suspension is adjustable it 1.1) About this Manual 1.2) A SPECIAL NOTE FOR PARENTS comes pre-adjusted and ready to ride from the factory. Section 2: Safety 6.1) Starting your non chain drive model 6.2) Starting your chain drive models 6.3) Starting your Bigfoot™, Go-Quad®, Super Go-Quad™ 6.4) “Easy Pull” pull starter 6.5) Engine Starting Instructions 6.
Section 1: Important Information 1.1 About this Manual Why you should read this manual: This manual was written to help you understand the operation and maintenance of your vehicle. It’s important for you to understand your new scooter/kart, its features and operations so that from your first ride you will get the most from your new scooter/kart and form proper habits to keep it maintained for optimum performance and safety for many years to come. Keep this manual.
Twist lever and cable: On the Bigfoot™ your twist lever engages or disengages the motor’s drive component. With the lever in the full up position the drive spindle must not touch the wheel in anyway. When the lever is in the full down position you should have ample slack in the cable to allow for spindle to be fully engaged with the tire. There are adjustment barrels on each end of the cable housing for the twist lever. 9.
B. Tires and Wheels: Check that pneumatic tires are properly inflated. Refer to the sidewall of the tire for recommended PSI. Checking PSI using a tire pressure gauge is recommended but you can also bounce your weight on the scooter and compare tire deflection to how it looks when you know the tires are properly inflated. Spin the wheels and check that the tires have not yet reached the wear marks on the tires, have ripped, torn, or show any signs of distress and replace as necessary.
Proper maintenance and care of your equipment are key factors in reliability and safety. Only you can insure for the care and maintenance for your equipment but make sure all users understand the importance of properly maintained equipment, all safety warnings/cautions, and recommended user practice contained in this manual for the safety of your equipment and all those that use it. 8.
2.7 Night Riding: Never ride your scooter/kart at night or in conditions of poor visibility. WARNING: Riding at dawn, dusk, or at times of poor visibility is illegal and dangerous. Section 3: Assembly 3.1 Pre-Assembled Scooters. Some models come completely and fully assembled so there is no assembly requirement. Remember to do a Mechanical Safety Check and make final adjustments to hand levers, and drive components. Oil chain and air filter if needed. 3.2 Some Assembly Required.
6.6 Motorized Riding WARNING: The exhaust contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Warm up the engine (30 to 60 seconds). With the Sport, X25, X-Ped®, and Super X-Ped™ engine running and with throttle set at idle, set the rear tire on the ground and immediately start walking alongside the scooter then step on the deck with both feet and with both hands firmly on the handle grips you can now begin to add throttle control.
Section 5: Controls Section 4: Oil & Fuel Information Your Go-Ped® has a two-stroke engine requires two-cycle oil to be mixed with gasoline. Use a high quality 2 cycle oil that is formulated for small air cooled engines. NOTE: Go-Mix II oil packets are formulated to reduce engine emissions, extend engine life and are recommended and available through your authorized Go-Ped® dealer. Go-Mix II is pre-measured for US gallon or goped® tank sizes and does not require measuring.
