User Guide

NOTE: The small drain hole in the edge of the gasket should normally
face opposite the forward direction of the vehicle—opposite the
arrow molded in the front of the base. Use silicone sealant to fill
opening around power cord.
IMPORTANT: Allow 3" of cord to remain under the light to ensure full
370° rotation.
Install the dash-mount control and connect the wiring harness.
Connect the positive-negative wires to a positive-negative
connection, preferably on the backside of the fuse box. The 12 Volt DC
power wires should be joined to the leads under the lamp with
appropriate automotive wire attachments. It is critical that polarity be
observed. The (+) lead of the unit is marked with a red tag. The power
should be fused at 15 Amps and be on an ignition switched circuit if
possible.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® is controlled with a programmable remote with 6561
different channels. This feature allows you the freedom to change the
channel selection, and the receiver relearns the new selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.
1. IMPORTANT: Disconnect power by removing fuse or
disconnecting vehicle battery.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small
screwdriver and select a position for each dip switch. *Please note
that the orientation of the +/– switch positions may vary among
different models of wireless remote controls.
The Golight® Model 2049/2067 is designed to be permanently
attached to a vehicle. The Combination Searchlight with Directional
Flexibility is controlled by a wireless remote and/or a dash-mount
remote, which gives the operator a full 370° horizontal rotation and a
135° vertical tilt with fingertip control. The Golight® provides superior
light penetration with Cr5 PentaBeam™ technology.
The Golight® Model 2049/2067 Includes:
• Golight® Searchlight
• Wireless Remote Control in Raincoat
(must be kept clean and dry)
• Dash-Mount Remote with 20' Wiring Harness
• 2 Duracell MN21 Batteries
• Permanent Mounting Gasket
• All Necessary Hardware for Mounting
MOUNTING INSTRUCTIONS
Determine the location for the light on your vehicle or boat. The small
arrow on the base indicates the normal forward direction of the light.
The light will rotate to the left of this arrow approximately 190° and to
the right approximately 190°. The beam will angle down about 45°
and angles up to 90°, a full vertical. The location should take into
consideration this beam movement to ensure optimum usability.
Once the position and orientation are decided upon—use the black
rubber gasket as a footprint to mark the mounting of base to vehicle.
Drill 7/64 inch holes for #7 screws to mount the light. Also drill 1/2
inch opening in the center to accommodate the wiring harness.
NOTE: When connecting the plug from the light to the harness,
please note the additional ground wires that are not included in the
plug. These grounds need to be connected.
Once the plug and grounds have been connected, the plugs and all
exposed wires need to be shielded with the enclosed aluminum tape,
this will help prevent any interference to your light. The grounding
strap at the dash remote also needs to be attached to a solid ground.
To connect the light to the wiring harness, put the gasket on the base
of the light and attach the light to the surface.
4. Insert both MN21 Duracell batteries with the +/– in the same
direction. Be sure batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED will light.
b. While holding the on/off button down, reinstall the power
(replace fuse or connect vehicle battery).
c. Keep your finger on the on/off button for 5-6 seconds, and then
release. The light should now be programmed.
OPERATION OF GOLIGHT® MODEL 2049/2067
1. Using the programmable wireless remote control, turn on the light
by depressing the on/off button.
2. With the 4-way arrows on the remote control, rotate your light to
the desired location. Depending upon conditions, the wireless
remote may be used up to 100 feet from the Golight®.
3. The speed of the light rotation can be controlled by depressing
the +/– button one time and by depressing it again to restore the
original speed.
4. The dash-mount remote can be used to control the rotation and
the on/off switch.
5. The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached.
BULB REPLACEMENT
The Golight® utilizes a Philips® H-9 bulb, which may be purchased
through Golight, Inc. — 308.278.3131 or 800.557.0098.