User Manual Floodlight Cam F2 EN Model: GF2
Customer Service Warranty 30 Days Return Policy and 12 Months Limited Warranty Get Customer Service via oc.support@gncchome.com Guide Channels Please follow our social media to get more information and help.
Introduction Your new Floodlight Cam is a smart home security system combining PIR motion sensed lighting and real-time video monitoring. It can monitor your home day and night, you'll always be the first to know when someone’s in your yard, and talk to him right away. LED Light Installation Base Lens Reset Button and TF card slot PIR Sensor Speaker Microphone Notice Do not dismantle or replace any parts of the product without professional guidance. This manual is for informational purposes only.
Installation Guide Recommended Installation Height 6.5-8.25 Feet above the Ground In this range of height, the camera will provide a detection distance from up to 49 feet. 5ft. Height Motion Sensor Horizontal Detection Coverage 7ft. Height Motion Sensor Horizontal 5° Detection Coverage 9ft. Height Motion Sensor Horizontal 10° Detection Coverage You can adjust the camera body up and down, left and right, for desired coverage area.
Tools You Need to Prepare (Not Included) Flathead Screwdriver Screwdriver Silicone Sealant Stepladder Goggles Pliers Notice To have the maximum product performance and avoid unnecessary environmental disturbance, please beware of the following conditions during product installation. 1) Do not install the product close to thermal sources, like air conditioner outdoor unit or kitchen smoke outlet, etc.
You Can Install the Floodlight Cam Follow These Steps: • Step 1: Shut power off at the breaker (not the switch) WARNING: Risk of electrical shock! 1) Please make sure the power voltage is 110-120V AC, 60 Hz. 2) Fix the ground fixture properly. 3) Always follow code standards when installing wired connections. 4) Do not connect this light fixture to a dimmer switch or timer. 5) Do not install near combustible or flammable surfaces.
• Step 3: Wiring the floodlight cam Remove the paper barrier from the EVA gasket (B), and adhere the gasket to the crossbar and outer edge of the round surface junction box. Ensure that the short screw on the crossbar is threading the hole of EVA gasket (B). Then wire as below 1) Use a wire nut (F) to connect the white wires together. The white wire on Floodlight Cam is a neutral wire. 2) Use a wire nut (F) to connect the black wires together. The black wire on Floodlight Cam is a hot wire.
• Step 5: Restore power for test Restore power at the breaker. In Setup Mode: The Floodlight Cam will begin making a sound. Now the Floodlight Light is working. ON Last step: Waterproof treatment After mounting the Floodlight Cam, then seal the junction box with silicone sealant to prevent water from leaking in. It is a very important and necessary protection in wet locations. Notice Please do not install the product in a harsh environment.
Continue with APP Setup Before you begin, please make sure you have the following minimum requirements. 1) Smartphone Running iOS 9.0 / Android 5.0, or later. 2) Home Wi-Fi Network (2.4 GHz ONLY). 3) Internet Access with an Upload Speed (At Least 2 Mbps). Step 1: Download WowCam APP You can scan the OR code below, or search WowCam in Google Play or APP Store to download the APP. Step 2: Add the Device Make Sure Phone Bluetooth Function is ON.
How to Use APP Select your Floodlight Cam on the APP home page, and then access various features and change settings via hints. outdoor Open a live video stream + Away Turn the lights on and off Check alarm events Check Video Recordings Device Sharing Settings Online outdoor Notice Due to continuous product improvement, all APP settings above are subject to change without prior notice, please always keep APP updated to the latest version.
Turn the lights on and off Live Stream Send messages and alerts Speak to visitors and hear what they have to say. Take a picture Record a clip of video Turn sound pick-up on and off Select video image sharpness Full screen Enter Settings page, you can view and modify any settings, upgrade the firmware and unbind the device. 1) Light setting Set a schedule for your lights to stay on. 2) Picture/View Rollover image and Modify video frequency.
3) Home/away Turn the alarm on and off, Select alarm schedule. Device Sharing Step 1: Invite your friends to download and install "WowCam" App, and register to log in. Step 2: By clicking the sharing icon, you can choose “Accont invitation” or “QR code invitation” to share the device.
Troubleshooting Tips • Serious stroboscopic picture showing in live view? It is mainly caused by different AC frequency, which can be solved by changing the AC frequency in App settings-Picture/View. • Device is offline in device list? Check whether the device network is good. If there is TF card inserted, please unplug the TF card, reset the device and router, then connect it again. (Insert the thimble into the reset hole and long press about 5 seconds.
Made in China Version 1.
