User's Manual

Multi-Color
Indicator Light
Volume
Buttons
Call
Button
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H710.
Features and
Functions Guide
TURNING HEADSET
ON AND OFF
To turn your headset on, open the headset
boom. The indicator light flashes blue (if
connected with a device) or is steadilly lit (if
ready to be paired).
To turn your headset off, close the
headset boom. The indicator light will turn
off.
WEARING THE HEADSET
Open the headset boom, then open the
earhook.
Loop the earhook over your ear.
Press the headset to your ear.
Point the headset boom towards your
mouth.
1
2
3
4
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off.
Press and hold down the desired
"volume up" button and open the boom.
Keep the button held down until the
indicator light flashes blue three times.
1
2
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
European Union Directives
Conformance Statement
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
Hereby, Motorola declares that this
product is in compliance with:
MAKING CALLS
Note: Your H710 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function Action
Make a voice dial call Tap the Call button
(Primary phone) and speak the
name after the tone
Make a voice dial call Tap the Call button
(Secondary phone) and either Voume
button and speak the
name after the tone
End a call Tap the Call button
Answer a call Open headset boom
or tap the Call button
(if boom is already
open)
Ignore a call Press and hold the
Call button until you
hear a beep
MAKING CALLS CONTINUED
Function Action
Redial last call Press and hold the
Call button until you
hear a beep
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
Reject second incoming Press and hold either
call Volume button until
you hear a beep
Transfer a call from the Press both Volume
headset to the phone buttons and Call
button
Disable the Press and hold
indicator light both Volume
buttons while
powering on headset
Mute or unmute a call Tap both Volume
buttons
Note: Some features are phone/network dependent.
CHANGING FOR USE
ON OTHER EAR
Open the headset boom,
then open the earhook
(90 ° from the headset).
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
1
2
3
4
You can wear your H710 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1
Open Earhook
2
Pull Earhook
Up
Hinge
Pin
INDICATOR LIGHT
With the Charger Plugged In
Headset Indicator Headset Status
Red Charging (battery
level less than 80%
charge)
Yellow Charging (battery
level more than 80%
charge)
Green Charging complete
When Checking Battery Level
Headset Indicator Headset Status
Red Battery at less than
10% charge
Yellow Battery between
10% and 80% charge
Green Battery at more than
80% charge
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
Three blue flashes Powering on/off
Steady blue Pairing mode
Rapid blue/purple flashes Pairing successful
Quick blue flash Incoming/outgoing call
Slow blue pulse Connected (on a call)
Slow blue flash Standby (not on a call)
Slow red flash Idle (not connected
to phone)
Slow purple pulse Connected call muted
Quick red flash Low battery
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
INDICATOR LIGHT
AUDIO TONES
CHECKING
BATTERY LEVEL
While turned on and not on a call, you can
check your headset’s battery charge level
by pressing and holding both Volume
buttons.
The indicator light displays charge status
until you release the buttons. See “Indicator
Light” for details on indicator light and
charge status.
DRAFT
DRAFT