User's Manual

Answering and Placing Calls
19 Put on the headset.
20 Set the headset/handset selector
to headset position.
21 Lift the handset
from the phone.
Answer or place
the call.
22 You can now move
freely away from
the base station. If
you move out of
transmission range,
you will hear a beep
in the headset every
10 seconds.
23 To end the call,
replace the handset
on the phone.
Netcom
Adjusting the Receive Volume
24 To increase or decrease the
volume, press the upper (+)
or lower (-) part of the
oval volume control on
the headset. When the
volume reaches maximum
or minimum, you will hear
a beep in your headset.
Muting the Microphone
25 To talk without the other
party hearing you, press
the mute button on the
headset. When the
microphone is muted,
you will hear a beep
every 3 seconds. When
the mute function is on,
you can still hear the
other party.
Recharging the Battery
26 To ensure optimum
battery life, when not
in use, place the headset
in the base station with
the headset/handset
selector in the handset
position. The battery
charging indicator
illuminates during
recharging. It takes 3
hours to fully charge
the battery. When fully
charged, the indicator
flashes. If battery
power gets too low,
you will hear a beep
in your headset every
20 seconds.
FCC Notice to Users
Upon request only, you must notify your telephone utility company (telco) of your intention to install or permanently remove an
FCC Part 68 registered device or system. Include the FCC Registration Number and the Ringer Equivalence Number (REN) located
on the amplifier label.
The telco has the right to make changes to their network, which may affect the operation of your equipment, provided you are given
adequate advance written notice to permit correct operation.
This device complies with part 15 of the FCC Rules and ICES-003 Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Complies with part 15 & 68, FCC Rules
Operation is subject to the following two rules:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Industry Canada requires Indoor Use Only
IC Notice to Users
The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications
network protective, operational and safety requirement as prescribed in the appropriate Terminal Equipment Technical Resource
Document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural
areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any
combination of devices subject only to the requirement that the sum of the ringer equivalence Numbers of all the devices does
not exceed 5.