Owner manual

2. Enterthenameusingthe or keystoselecteach
character then press the CALLbuttontomovetothe
nextcharacterposition.
3. WhennishedpressandholdtheCALLbutton.The
MMSIwillbeautomaticallytransferredfromthecalllist
totheAddressEntrypage.
4. PressandholdtheCALLbuttonagaintoconrmand
storethenewcontactintheaddressbook.‘Saving’will
bedisplayedastheaddressisstored.
To Erase The Displayed Entry From The Call Log:
1. Select‘Erase’fromtheAddressbookmenuandpressthe
CALLbutton.‘EraseEntry?’isdisplayed
2. PressandholdtheCALLbuttontoconrm.
To Erase all Logged Calls:
1. Select‘EraseLogs’fromtheAddressbookmenuand
press the CALLbutton.‘EraseAll?’isdisplayed.
2. PressandholdtheCALLbuttontoconrm.
DISPLAY
Tocongurethedisplay,selectthe‘DISPLAY’optionfrom
themainmenu.ThefollowingDisplayoptionsareavailable
• Backlight
• Contrast
Backlight Adjustment
1. Toadjustthedisplay’sbacklighting,select‘Backlight’
fromtheDisplaymenuthenpresstheCALLbutton.
2. Usethe or keystoselect‘OFF’,‘DIM’or‘BRIGHT’.
Thedisplaychangesimmediatelywitheachselection.
3. PresstheCALLbuttontoaccepttheselection.
Contrast
1. Toadjustthedisplay’scontrast,select‘Contrast’fromthe
DisplaymenuthenpresstheCALLbutton.
2. Usethe or keystoadjustthecontrastsothatthe
displayiseasilyreadable.Thecontrastwillchangewith
eachkeypressandareferencevaluefrom-20to+20
willbedisplayed.Thecontrastsettingisdependenton
yourviewinganglesowerecommendyouadjustthe
contrastfromyournormalviewingposition.
3. PresstheCALLbuttontoaccepttheselection.
SETUP
TheSetupmenuconguresthegeneraloperationofthe
radio.ThefollowingmenuisdisplayedinSetup
• KeyBeep
• AlarmBeep
• AutoChannel
• PosReply
• IndivReply
• UIC
• ChnlName
• NMEA-1
• NMEA-2
Key Beep
Changesthevolumeofthebeepsthatareheardwhenthe
keysarepressed.
Tochangethekeybeepvolume;
1. Select‘KEYBEEP’fromtheSetupmenuthenpressthe
CALLbutton.
2. Usethe or keystosettheBeepvolumeto‘HI’,
‘MED’,‘LOW’or‘OFF’.
3. PresstheCALLbuttontoaccepttheselectionandreturn
tothe‘SETUP’Menu.
Alarm Beep
ChangesthevolumeoftheAlarmbeeps.
Tochangethealarmvolume;
1. Select‘ALARMBEEP’fromtheSetupmenuthenpress
the CALLbutton.
2. Usethe or keystosettheAlarmBeepvolumeto
‘HI’,‘MED’or‘LOW’.
3. PresstheCALLbuttontoaccepttheselectionandreturn
tothe‘SETUP’Menu.
NOTE: TheEmergencyAlarmvolumeisalwayssettoHigh
andisnotaffectedbythisadjustment.
Auto Channel
AutoChanneldeneswhetheryourradiowillchange
channelsautomaticallywhenrequestedbyanothervessel’s
DSCcall.
1. Select‘AUTOCHNL’fromtheSetupmenuthenpressthe
CALLbutton.
2. Usethe or keystosettheAutoChannelfeatureto
ONorOFF.
 –Select‘ON’toallowyourradiotochangechannels
whenrequestedbyanincomingDSCcall.
 –SelectOFFtoignoreincomingchannelchangerequests
fromDSCcallsandremainontheselectedchannel.
3.PresstheCALLbuttontoaccepttheselectionand
returntothe‘SETUP’Menu.
PAGE16 INSTRUCTIONMANUAL GX600D