User Guide

ManualsBrandsGLP ManualsOtherGLP CL1-PLUS Creative Light 1 Plus RGB LED

Rev. 20210331-1

Safety Instructions

Important: This process deletes all individual

custom settings. Note that you will lose

connection to your controller!

Linking to a CRMX Transmitter

Loading Factory Backup

Transport Lock

Whenever CRMX is enabled and the ﬁ xture

is not already linked, the device searches for

a CRMX transmitter. To link the device with a

new CRMX transmitter, unlink the device and

start the linking process at the transmitter.

• Follow all applicable safety regulations when installing and using this

product.

• Secure this product against falling by using a safety attachment when

installing overhead.

• Do not operate the product in high temperatures or direct sunlight.

• Do not apply power to a product or battery charger that is damaged or

deformed.

• Do not expose the product or charger to water or humidity.

• The product and charger contain no user-serviceable parts. Do not try

to open or modify them.

• Do not look directly into the light output. Looking into the output at

close range may cause eye injury or irritation.

• Be ready for the product to light up suddenly when a command is sent

via remote control, signal gets lost or external power is switched off.

• Do not look at the LEDs with a magnifying glass or other optical

instrument that may concentrate the light output.

• Use only optical accessories that are supplied or approved by GLP.

• The product can become hot during normal operation. Take pre-

cautions to prevent accidental physical contact with the product. Allow

to cool before handling.

• Ensure free airﬂ ow and adequate ventilation around the product.

• Do not illuminate surfaces and objects that are less than 0.3 m (1 ft.)

from the product.

• Keep the product away from ﬂ ammable or volatile materials.

• This product contains a rechargeable one cell lithium-ion battery rated

3.7 V / 10,000 mAh.

• Respect all applicable laws and regulations for the transport, storage

and disposal of batteries.

• Do not expose the battery to ﬁ re or heat. Protect it from physical shocks.

Do not allow it to come into contact with water. Do not short-circuit

a lithium-ion battery or you may cause a battery explosion.

• Recharge the battery immediately when it is discharged.

• Charge the battery at an ambient temperature of between 15°C (59 °F)

and 35°C (95°F).

• Leave the product’s container or ﬂ ightcase open during charging.

• Charge the battery fully before storing the product. Partially charged

batteries lose capacity. Charge the battery every six months when the

product is not in use.

• Do not connect a battery charger to a product that may be damaged or

faulty.

• If the battery becomes faulty or will not hold a charge, replace it with

an original spare part from GLP only. The battery must be serviced by

authorized personnel only.

• Send the product to an authorized recycling center at the end of its life-

time. Do not dispose of the product or battery with household waste.

Send the product’s packaging for recycling.

If ﬁ xture is powered on: Press and hold the Enter button for

10 seconds. Fixture loads factory backup. All custom settings and

individual conﬁ guration are returned to factory default settings.

If the ﬁ xture is switched on and not connected to power,

pressing and holding Menu and Enter buttons simultaneously

for 10 seconds puts the ﬁ xture into Transport Lock mode. This

locks all control buttons for long-term storage and safe trans-

portation.

To unlock the ﬁ xture, connect it to power using the charging

ports or USB.

Unlinked device

CRMX Transmitter with

active linking process

Unlinked device

1. Switch on the device.

2. Set ﬁ xture to CRMX control:

Menu > Signal Settings > Signal Source: CRMX

3. Unlink ﬁ xture:

Menu > Signal Settings > CRMX Link : Link / Unlink

4. Start linking process at CRMX transmitter

(read transmitter’s user manual)

The ﬁ xture is shipped from factory with

Transport Lock enabled. Connect the

ﬁ xture to power before ﬁ rst use.

For further detailed information look up the user manual PDF

available for download on our website www.glp.de

Charging

Switching on / off

Connect the device to power using either its USB-C con-

nector and a standard USB charging power supply (not

included) with minimum 1 amp power or the optional GLP

Creative Light Docking Station (not included).

Charge the product to 100 % before ﬁ rst use.

First LED pixel ﬂ ashing green: charging in progress

First LED pixel constant green: charging process ﬁ nished, 100% charged

Switch the ﬁ xture on and off by pressing and holding the

left Menu button for 3 seconds. Increasing / decreasing

white pixels indicate the ﬁ xture starting up or shutting down.

Menu button

(press & hold for 3 sec)

Signal Sources

The Creative Light 1 Plus can be controlled in three different signal source modes:

Don’t forget to set the Control Mode and DMX

Address when linking to the CRMX transmitter.

Manual Mode (IR Remote Control)

Manual Mode lets you manually control the Creative Light 1 Plus via the integrated con-

trol panel or the included IR remote control unit. You can set a background color and

add pattern macro effects on top of the background. Sound2Light for automatic color

changing is also available.

Don

CRMX (DMX via LumenRadio CRMX)

Using LumenRadio CRMX lets you connect the Creative Light 1 Plus to any Lumenradio

CRMX-compatible DMX transmitter. This lets you control the ﬁ xture with a standard

DMX signal and integrate it into an existing DMX infrastructure. CRMX operating mode

lets you control many more parameters, gives a wider selection of integrated effect

patterns and offers individual pixel control. In this mode, the indicator CRMX appears in

the bottom right corner of the display.

Important Note: By default the ﬁ xture is set to Signal Source: CRMX and No-Signal:

Manual Control. This means the ﬁ xture automatically switches to manual control

(IR remote) if no valid CRMX signal is being received or the ﬁ xture is not linked to CRMX.

You can change this setting in the ﬁ xture’s control menus under Signal Settings /

Signal Source and Fixture Settings / No-Signal Behavior.

GLP Creative Light App via GLP iQ.Mesh

The Creative Light 1 Plus lets you create light scenes using the GLP Creative Light App

and innovative GLP iQ.Mesh technology. Set Signal Source to GLP iQ.Mesh and open the

GLP Creative Light App to link the Creative Light 1 Plus and get control.

The device shows its current conﬁ guration status as followed:

1 pixel rotating red: device unlinked to iQ.Mesh

1 pixel rotating green: device linked to iQ.Mesh

For more information please see the guidance in the GLP Creative Light App.

You can always switch between signal sources by pressing and holding the

Down button for 3 seconds.

glp.de

more info:

Enter button

(press & hold for 10 sec)

Enter buttonMenu button

(press & hold both

for 10 sec)