GWG130WV Home Gateway User Manual Page 1
PLEASE READ THESE SAFETY PRECAUTIONS! RF Energy Health Hazard The radio equipment described in this guide uses radio frequency transmitters. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come in close proximity to the front of the antenna while the transmitter is operating.
Table of contents 1. OVERVIEW ............................................................................................................................................... 4 1.1 USER INTERFACE SPECIFICATION ............................................................................................................ 4 1.2 WI-FI INTERFACE(IDU) .......................................................................................................................... 4 GETTING STARTED.......................
1. Overview AM4000M is an indoor multiservice gateway unit (IDU) that supports advanced networking, VoIP gateway and WLAN AP functionalities. It enables wide service coverage and provides high data throughput and networking features to customers who needs easy broadband access, low cost VoIP service and Wi-Fi connectivity. 1.1 User Interface Specification Model AM4000M Description & User Interface - 1 RJ45 10/100M ETH (PoE),2 RJ45 10/100M ETH,1 RJ11/FXS Line Power, NET, Wi-Fi, LAN1-2, LINE, WPS 24V/1.
CPE Unit: Unpacking the Equipment Table 2-1 lists all the standard parts that are supplied in your LTE CPE Unit Installation Package. Please take the time to unpack the package and check its contents against this list. 2.2 Installing the Equipment Device logic connection AM4000M is user-friendly and easy to setup. To power on the IDU device, the IDU must uses a 24V DC power supply adapter. The power adapters can operate in 90-250V AC range and therefore can be used in different countries.
LED Display LED Indicator LED Indicator Function Description PWR Power Indicator Orange Color – Device is power on and booting Green Color – Device at work NET WAN Indicator OFF – NO wireless network access. Blinking Green – WAN data transmission in progress.
3.3 Network Configuration Modify MTU Size The default Operation Mode is Router, and the PC of the user that connected to device LAN port will obtain IP address via DHCP server of the device. The default MTU Size is 1500, user can modify the MTU Size if necessary.
Note: After configure any parameters to the device, you must click the “Apply””Save & Commit “button to save the configuration otherwise the configuration will not take effect. 3.4 Wi-Fi Configuration-Modify SSID/Security In Wi-Fi configuration, the user can modify the default SSID and select the desired Security Policy to protect device Wi-Fi access. For easy configuration, the user can use one of the following three common security policies for setup.
WPS setting When a quick and convenient access to connect is needed, the WPS function is useful. 3.5 Service Configuration-DMZ Setting By enabling this option will make the specified local LAN host (DMZ IP) was exposed to the Internet, all ports can be accessed by other computers on the Internet.
3.6 Voip Configuration-SIP Account Setting In this configuration page, the user requires to enter the SIP user name, account and password information if he desires to configure the VoIP networking. And the register status must to enable, the register server IP also requires to configure. The SIP server configuration will be performed by the network operator via admin management. The SIP account status is displayed for user information.
3.7 System Maintenance WEB GUI menu to configure the device in more details (see diagram below). The configuration is easy to use and self explanatory. You can select the language or modify the web login password via the General Setting page. Telnet Enable all and modify password You can also set Telnet Management as Enable All for all the users, include WAN user, LAN user and the Wireless station to telnet to the CPE. cmd shell and run command: telnet 172.16.1.
Page 12
Firmware Upgrade over HTTP Click on the Browser button to select the firmware file to be uploaded to the device. Click the” Apply” button to begin the upgrade process. Please do not interrupt the upgrade process and continue to wait for the following pop window to appear, then Restore Defaults and Reboot. Load Factory Default Click the “Load Default” button will restore the device to original factory setting.
4. Hardware Reset In case the user forgot the login password, the device can be reset by pressing (using a pin) the reset button next to the LAN port for 10 seconds and then wait for the CPE to reboot and complete the restart. The user can then be allowed to use the original default login password to gain access to the unit WEB GUI again. After factory reset, the device may need to be reconfigured by the user or even operator to gain network access.
