Installation Guide

HEADERS & JAMBS
DOOR HEADER
Drill and counter-sink outside top surface
for 10-32×7/16" and 1/4-20×11/4"flat head
screws as shown.
Drill and counter-sink for 10-32 Flat
Head screws
7
/16"
Drill and-counter-sink for 1/4-20 Flat
Head screws
1
12 /2"
3
1 /8"
3
2 /4"
COVER PLATE
Drill 13/4" hole as shown.
Drill 1/2" hole as shown.
1
Drill / " Holes
2
13
Drill /4" Hole
14"
11
/16"
3
2 /4"
3
10 /4"
Install anchor using #10×9/16"
pan head self-threading screws.
Mount door header on anchor using 10-32
×7/16" flat head self-tapping screws.
HINGE JAMB
Drill holes for #10 pan head
self-threading screws as shown.
Bottom of header
1
/8"
Door Clearance
Top of door
3
1 /16"
7
/16"
3
1 /8"
SIZE
NO. OF TURNS
1
2
3
9
0
3
Spring power VS door size chart
DIRECTION
INTERIOR
MAXIMUM WIDTH
EXTERIOR DOOR
MAXIMUM WIDTH
FACTORY PRESET
CLOCKWISE (+)
CLOCKWISE (+)
Spring Power
Adjustment
_
+
30"
34" 30"
38"
34"
3 spring power
81/2 OPENING FORCE
"S" Type Side Loading Arm
Drill or drill and tap holes in top of door
as shown.
1
1
Make 2 /4" x /2" cut-out in top of door as
shown. Cut-out must be on the inside of
the door.
1 11
Install arm using /4-20 x /4" flat head
7
machine screw and /8" washer. Install
11
1
3 1
/2-13 x /4" arm stud and /4-20 x /8"
dome head arm adjustment screw. Laterally
adjust canter of the arm spindle retainer
5
2 /8" from hinge edge of door (not
including weatherstripping). Canter
arm in the top rail by adjusting the two
1
/4-20 x 1" hex head cantering bolts.
After installation of door, attach dress
pate with self-threading screws.
NOTE: before attaching dress plate, make
1 7
certain the three /4-20 x /8" socket head
clamp bar screws with lock washers are
tightened securely.
TOP DOOR RAIL
Canter pivot base against door jamb on
1 1
hinge side. Mark and drill /4" holes 1 /2"
deep in floor for plastic expansion plugs.
1
Mount base using #12 x 1 /4" plastic
1
expansion plugs and #12 x1 /4" flat head
wood screws.
1
Install pivot stud and bearing with /2-20
hex lock nut as shown, and adjust bearing
height for proper door clearance and
firmly tighten lock nut.
1
When using threshold, drill 1 /4" hole for
3
clearance of pivot base on canter line 2 /4"
from hinge end of threshold.
NOTE: When threshold is not used, pivot
bearing stud must be shortened by sawing
1
off at score /2" from bottom
FLOOR MOUNT PIVOT
Drill and Tap
1
/4-20Threads
3
Drill /32"Holes for
Self-threading
Dress Plate Screws
Drill and Tap
1
/2-13 Threads
7
Drill /16"Hole
for Adjustment
3
5 /8"
7
1 /16"
3
1 /4"
1
2 /4"
5
2 /8"
1
/2"
3
/8"
THRESHOLD MOUNT PIVOT
Drill hole in threshold as shown. Install
threshold adapter nut from top and secure
with 3/4-16 hex jam nut underneath. Install
pivot stud and bearing wit 1/2-20 hex lock
nut as shown and adjust bearing height for
proper door clearance and firmly thghten
lock nut.
Score
Hex Lock Nut
Threshold
Adapter nut
Hex Jam Nut
3
Drill /4" Hole
Pivot Stud and
Bearing
3
2 /4"
Pivot Stud and
Bearing
Floor Mount
Pivot Base
Hex Lock Nut
Score
1
2 /8"
1"
SIDE LOADING
Drill and tap 1/4-20 holes in bottom rail of
door as shown. Install pivot bearing retainer
in bottom of door using two 1/4-20
x5/8" pan head machine screws and lock
washers.
Laterally adjust canter of pivot bearing
retainer 25/8" from hinge edge
of door (not including
weatherstripping)
and tighten
screws
securely.
BOTTOM DOOR RAIL
Pivot Bearing
Retainer
3
1 /4"
3
3 /
4
"
Side Loading