ASSEMBLY INSTRUCTION OUTDOOR FOUNTAIN WITH LED LIGHTS & PUMP Please carefully unpack and identify each component before beginning assembly. Before you begin, please refer to parts list to make sure that you have all parts. Please take care when assembling the unit and always place the parts on a clean, soft surface. If you require assistance with assembly or parts, please call 888-357-7263.
PRE-INSTALLATION INSTRUCTIONS 1. Please read through this instruction before attempting to assemble, operate or install. 2. Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. 3. Please install the fountain on a flat, level surface close to an electrical outlet. 4. This product is designed for outdoor use, it can be used indoors, however splashing may occur.
11. The fountains are not manufactured to withstand extreme temperatures. Improper storage that allows water to freeze within a product may cause damage. 12. Keep the fountain away from high temperatures or heat sources. 13. Do not use the pump in water above 86°F (30℃). 14. Disconnect the power cord from the outlet by holding the plug. Do not lift, carry, or pull the pump by the power cord. 15. If the entire fountain falls into the water accidentally, turn off the circuit breaker immediately. 16.
STEP-BY-STEP ASSEMBLY PLEASE CAREFULLY UNPACK AND IDENTIFY EACH COMPONENT BEFORE BEGINNING ASSEMBLY. BEFORE YOU BEGIN, PLEASE REFER TO PARTS LIST TO MAKE SURE THAT YOU HAVE ALL PARTS. STEP 1 Place the Fountain Base (B) on a flat, level surface close to an electrical outlet. Allow enough space to access the pump. A STEP 2 B C D E F Remove the Pump Cord (C) from the packaging and adjust the water flow control to the lowest setting to avoid splashing until the fountain is completely assembled.
STEP 3 Make the long cable from the Pump (C) out through the bottom of the Fountain Base (B). C STEP 4 Connect the water hose preassembled inside of the Top Ball (A) into the Pump (C). Please keep the pump still out.
STEP 5 Connect the light cable preassembled inside of the Top Ball (A) to the branch cable from the Pump (C). Tighten the connector by twisting clockwise, then place the Pump (C) into the reservoir at the top of the Fountain Base (B). A C B STEP 6 Put the Black Lid (E) onto the tube inside the Fountain Base (B).
STEP 7 Put the Top Ball (A) onto the Fountain Base (B). A B STEP 8 Connect the long cable from the Pump (C) to the Power Plug (D). Tighten the connector by twisting clockwise and keep the power plug sit outside. NOTE: Please double check all connecters to make sure they are tightened.
STEP 9 Gently pour water into the fountain basin, make sure the water completely submerges the Pump (C). NOTE: For the first-time you operate the pump, it normally needs about 1-2 minutes for the air to be completely expelled to make sure the water begins to flow. STEP 10 Place Pebble (F) around the ball.
STEP 11 Connect the Power Plug (D) into your local power supply. NOTES: 1. Make sure there is no water on the power plug. 2. Allow the pump power cord to hang at a lower level than the wall outlet to form a “drip loop.” This will help to prevent water from dripping down the power cord and getting into the wall outlet. D DRIP LOOP D STEP 12 Once set up, you can adjust the pump water flow rate control to achieve the desired effect (see step 2 for adjustment) and enjoy your new fountain.
PUMP SAFETY & TROUBLESHOOTING Min. water level Filtering cover MIN Housing MAX Rotor Flow rate control CARE AND MAINTANCE 1. Check regularly that the water reservoir has sufficient water to always cover the pump. It will be necessary to check more frequently in warm or windy weather. 2. Do not allow the pump to freeze. During cold spells, remove the pump from the water feature and place in a water-filled container in a frost-free position. DO NOT store the pump dry. 3.
TROUBLE SHOOTING 1.If the pump fails to run: POSSIBLE CAUSE CORRECTIVE ACTION a) Pump is not covered with water. Add more water to the reservoir. b) Pump or fountain is blocked. Disconnect fountain from power source, remove any obstruction, and clean bowl and tubing. c) Pump is not secured correctly Disconnect fountain from power source, pour out any remaining water, and ensure the tubing in the reservoir is tightly secured to the pump outlet.
