Assembly Instruction 4 PIECE PATIO WICKER SOFA SET
PRE-ASSEMBLY PREPARATION WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT • Please read through this instruction before beginning assembly. • Two adults assembly is recommended. • Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
HARDWARE LIST Bolt (J) Bolt (K) M6 x 15mm M6 x 35mm Qty: 20 Plastic Cap (N) Bolt (L) Washer (M) M6 x 50mm Qty: 28 Qty: 12 Qty: 60 Wrench (O) Qty: 60 Qty: 1 NOTE: From step 1 to step 4 is for loveseat sofa assembly. Please find panel A1, B1, C1, C2 and D1 firstly. Step 1 Attach Seat Panel (A1) to Front Panel (B1) by using 4 medium Bolts (K) and 4 Washer (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened.
Step 2 Attach Right Armrest (C1) and Left Armrest (C2) to Front Panel on both side by using 4 medium Bolts (K) and 4 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened. M C2 K N C1 Step 3 Attach Backrest Panel (D1) to the Seat Panel by using 4 medium Bolts (K) and 4 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened.
Step 4 Attach Backrest Panel (D1) to the Armrest Panels on both side by using 4 long Bolts (L) and 4 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened. D1 M L N NOTE: From step 5 to step 8 is for single sofa assembly, the way is similar to loveset sofa. Please find panel A2, B2, C1, C2 and D2 firstly. Step 5 Attach Seat Panel (A2) to Front Panel (B2) by using 2 medium Bolts (K) and 2 Washers (M).
Step 6 Attach Right Armrest (C1) and Left Armrest (C2) to Front Panel on both sides by using 4 medium Bolts (K) and 4 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened. M C2 K N C1 Step 7 Attach Backrest Panel (D2) to the Seat Panel by using 2 medium Bolts (K) and 2 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened.
Step 8 Attach Backrest Panel (D2) to the Armrest Panels on both side by using 4 long Bolts (L) and 4 Washers (M). Finally put bolt caps (N) until all parts have been connected and bolts are tightened. M D2 L N NOTE: From step 9 to step 11 is for table assembly. Please find panel E, F, G, H and I firstly. Step 9 Attach 4 Table Legs (F) to the Table Top (E) by using 4 short Bolts (J) and 4 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened.
Step 10 Attach 2 Front Panels (G) and 2 Side Panels (H) to the table legs down by using 8 short Bolts (J) and 8 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened. N G J H Step 11 M Fix each panels to the table legs up by using 8 short Bolts (J) and 8 Washers (M). Finally put Bolt Caps (N) until all parts have been connected and bolts are tightened.
Step 12 Put Glass Top (I) to the table stand. I Step 13 Put on seat cushion and back cushion. Please make sure all bolts are properly tightened before use.
