Assembly Instruction TWO DOOR WOOD CABINET
PRE-ASSEMBLY PREPARATION WARNING: MAXIMUM LOAD NOT EXCEED 10LBS ON SHELVES. • CAUTION: Assembly will require at least 2 adults. DO NOT use power tools.To prevent serious injury or death, this product is equipped with a wall anchoring system. Before this product can be used, the wall anchoring system must be installed as directed in the assembly instructions. • CARE AND CLEANING: DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Clean with mild soap on a soft rag.
PART DESCRIPTION QTY PART DESCRIPTION QTY A LEFT FRAME 1 I LEFT DOOR 1 B RIGHT FRAME 1 J BOTTOM PANEL 1 C FRONT BOTTOM SUPPORT BAR 1 K TOP PANEL 1 D BACK BOTTOM SUPPORT BAR 1 L BACK PANEL 3 E BACK CROSS BAR 2 M TOP FIXED SHELF PANEL 1 F LEFT SIDE PANEL 1 N MIDDLE MOBILE SHELF PANEL 1 G RIGHT SIDE PANEL 1 O BACK PLASTIC STRIP 2 H RIGHT DOOR 1 PARTS LIST LEFT FRAME (A) RIGHT FRAME (B) Qty: 1 BACK CROSS BAR (E) Qty: 1 LEFT WOOD PANEL (F) Qty: 2 LEFT DOOR (I)
TOP FIXED SHELF PANEL (M) MIDDLE MOBILE PANEL (N) Qty: 1 BACK PLASTIC STRIP (O) Qty: 1 Qty: 2 HARDWARE LIST CAM (1) CAM LOCK (2) PHILLIPS SCREW (3) Ø15*9mm Qty: 8 PHILLIPS SCREW (5) Ø4*29mm Ø4*37mm Qty: 8 M6*12mm Qty: 6 ALLEN WRENCH (9) M6*25mm Qty: 4 PIN (7) ALLEN BOLT (6) Qty: 4 Ø4*12mm Qty: 4 GLUE (11) WALL ANCHOR (13) Ø8.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 1 CAM 11 GLUE SKETCH QTY 2PCS STEP 1 1 11 1 11 F Insert cam (1) into left wood panel (F) and fully tighten. Place a small dab of glue into the adjacent holes as shown in the diagram. REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 1 CAM 11 GLUE SKETCH QTY 2PCS STEP 2 1 11 1 11 G Insert cam (1) into right wood panel (G) and fully tighten. Place a small dab of glue (11) into the adjacent holes as shown in the diagram.
REQUIRED HARDWARE IN THIS STEP STEP 3 NO. DESCRIPTION 10 WOOD DOWEL 11 GLUE Place a small dab of glue (11) into the outside holes on the edge of top fixed shelf panel (M) and insert wood dowels (10) into the holes. 10 10 SKETCH QTY 4PCS 10 11 10 11 M 11 11 M STEP 4 Place top fixed shelf panel (M) on edge. Align the cams (1) in Left wood panel (F) and right wood panel (G) with the holes in the edge of top fixed shelf panel (M) and slide into place as shown in the diagram.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 2 CAM LOCK SKETCH QTY 4PCS PHILLIPS SCREW DRIVER NOT INCLUDED STEP 5 Insert cam lock (2) into top fixed shelf panel (M) and tighten with phillips screw driver. M 2 G 2 F REQUIRED HARDWARE IN THIS STEP STEP 6 NO. DESCRIPTION 1 CAM 11 GLUE 11 1 1 SKETCH QTY 4PCS Insert cam (1) into top panel (K) and fully tighten. Place a small dab of glue (11) into the adjacent holes as shown in the diagram.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 10 WOOD DOWEL 11 GLUE SKETCH 4PCS STEP 7 Carefully set the assembled panels upright as shown in the diagram. Place a small dab of glue (11) into the outside holes of the edges of left wood panel (F) and right wood panel (G) and insert wood dowels (10) into the holes. 10 11 2 10 11 M F G STEP 8 Align the cams (1) in the top panel (K) with the holes in Left wood panel (F) and right wood panel (G) and lower into place.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 2 CAM LOCK SKETCH QTY 4PCS PHILLIPS SCREW DRIVER NOT INCLUDED STEP 9 Insert cam lock (2) into left wood panel (F) and right wood panel (G) and fully tighten with phillips screwdriver. K REQUIRED HARDWARE IN THIS STEP STEP 10 NO. DESCRIPTION 10 WOOD DOWEL 11 GLUE SKETCH QTY 4PCS Carefully turn the assembled parts over as shown in the diagram.
STEP 11 Slide back panel (L) into the grooves of left wood panel (F) and right wood panel (G). Place plastic strip (O) in between each back panel (L) as shown in the diagram.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 11 GLUE STEP 12 Place a small dab of glue (11) into the outermost holes bottom wood panel (J) as shown in the diagram. SKETCH QTY 11 11 J 11 11 STEP 13 Align the wood dowels of left wood panel (F) and right wood panel (G) with the holes in bottom wood panel (J) and lower into place.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 3 PHILLIPS SCREW Ø4*37mm SKETCH QTY 4PCS PHILLIPS SCREW DRIVER NOT INCLUDED STEP 14 3 Secure the bottom wood panel (J) to left wood panel (F) and right wood panel (G) with phillips screw (3) using phillips screwdriver. Fully tighten screws. 3 3 J 3 REQUIRED HARDWARE IN THIS STEP NO.
STEP 16 Carefully place the assembled metal frame over the assembled cabinet as shown in the diagram.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH 4 ALLEN BOLT M6*25MM 4PCS 5 PHILLIPS SCREW Ø4*29MM 6PCS 9 ALLEN WRENCH PHILLIPS SCREW DRIVER QTY NOT INCLUDED STEP 17 Attach the the metal frame to bottom wood panel (J) with phillips screw (5) using phillips screwdriver. Fully tighten all screws and bolts. A D 5 B C 5 Attach left frame (A) and right frame (B) to the assembled cabinet with allen bolt (4) using allen wrench (9).
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SKETCH 8 PHILLIPS SCREW Ø4*12MM QTY 4PCS PHILLIPS SCREW DRIVER NOT INCLUDED STEP 18 With assistance, carefully turn the assembled cabinet onto it's feet as shown in the diagram. Attach back cross bars (E) with phillips screw (8) using phillips screwdriver. 8 8 8 E 8 REQUIRED HARDWARE IN THIS STEP SKETCH NO.
REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 7 PIN SKETCH QTY 4PCS STEP 20 Insert pin (7) into the pre-drilled holes of left wood panel (F) and right wood panel (G) as shown in the diagram. Then p lace the middle mobile shelf panel (N) onto the pins (7). The shelf can be adjusted up or down by moving the level of the pins (7). 7 N STEP 21 Press this pin Press the door pins down on left door (I) and right door (H) until they click.
STEP 22 Place the wheels of left door (I) in the back bottom chute. Align the top of the left door with the back upper slot and press the buttons on the back of the door to release the pins. Press this pin and the guide rod will slide into the slot I First put the wheels into back bottom chute If the door is to tight, turn the adjustment screw counter clockwise to raise the wheel up and lower the door.
STEP 24 Place the wheels of right door (H) into the bottom front chute. Align the top of the door with the top front slot and press the buttons on the back of the door to release the pins. Press this pin and the guide rod will slide into the slot I H guide rod will slide into the slot First put the wheels into bottom front chute STEP 25 If the door is to loose, turn the adjustment screw clockwise to lower the wheel and raise the door.
REQUIRED HARDWARE IN THIS STEP NO. 8 DESCRIPTION SKETCH QTY 1 PC PHILLIPS SCREW Ø4*12mm 12 1 PC ANTI-TIPPING STRIP 13 WALL ANCHOR Ø 8.5*30mm 1 PC 14 PHILLIPS SCREW Ø 4*25mm 1 PC 15 2 PCS STEEL PLATE PHILLIPS SCREW DRIVER NOT INCLUDED 8 NOT INCLUDED 12 13 NOT INCLUDED WALL WALL 14 15 WALL 12 NOT INCLUDED STEP 26 Attach steel plate (15 ) to top panel (K) with screw (8) using screwdriver. Place assembled unit in desired position.
STEP 27 H To avoid injury, please open the cabinet doors as directed in the diagram.
