Specification

SHIPPING
DI
RECTIONS FOR USE
PRECAUTIONS
G
LD2
0XX
-
4
–
9
/11
product. Steel - Prime with the appropriate waterborne or
solventborne metal primer. Galvanized Metal and Aluminum -
Prime with the appropriate waterborne metal primer.
PREVIOUSLY PAINTED SURFACES: Wash to remove
contaminants. Rinse thoroughly with water and allow to dry. Dull
glossy areas by light sanding. Remove sanding dust. Remove loose
paint. Prime bare areas with primer specified under NEW
SURFACES.
WARNING! If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear an NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
TINTING: Tint the appropriate base with universal colorants.
SPREADING RATE: Apply at 300-400 sq ft/gal (7-10 m
2
/L). Actual
coverage may vary depending on substrate and application method.
Deeper shades of yellow, orange, pink, red and other colors may
require multiple coats.
APPLICATION: Mix thoroughly before use. May be applied by
brush, roller or airless spray. Standard roller application should be
used for best results. No thinning required. For airless spray, use a
.015”-.019” tip at 2000 psi, adjust pressure as needed. For best
touch-up results with airless spray, backroll airless spray area and
touch-up with a standard roller. Application by conventional spray is
not recommended. Two coats are required for new and uncoated
surfaces. An additional coat may be necessary for dramatic color
changes, dark colors or over rough surfaces for optimal appearance
and hide. Do not apply when the surface or air temperature is below
50ºF (10ºC). Provide good ventilation and warmth for normal drying.
DRYING TIME: At 77ºF (25ºC) and 50% R.H., dries to touch in 30-
60 minutes and to recoat in four hours. Low temperature, high
humidity, thick films or poor ventilation will increase these times.
CLEAN-UP: Clean hands and tools immediately with warm, soapy
water. Clean spills right away with a damp cloth.
WASHING INSTRUCTIONS: After 30 days or when paint has
fully cured, areas may be washed using a non-abrasive, mild
detergent solution and cellulose sponge.
WARNING!
CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED. WHEN TINTED, CONTAINS
ETHYLENE GLYCOL AND DIETHYLENE GLYCOL. ETHYLENE GLYCOL CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS
BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. DIETHYLENE GLYCOL MAY CAUSE CENTRAL NERVOUS SYSTEM
EFFECTS AND LIVER, KIDNEY DAMAGE. USE ONLY WITH ADEQUATE VENTILATION! KEEP OUT OF THE REACH OF CHILDREN. For emergency
information call [phone]. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. If
sanding, wear a dust mask to avoid breathing of sanding dust. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. Avoid contact with eyes
and skin. If you experience eye watering, headaches, or dizziness, leave the area. If properly used, a respirator may offer additional protection. Obtain professional advice before
using. Close container after each use. FIRST AID: For skin contact, wash thoroughly with soap and water. If any product remains, gently rub with petroleum jelly, vegetable or
mineral/baby oil then wash again with soap and water. Repeat as needed. Remove contaminated clothing. For eye contact, flush immediately with plenty of water for at least 15
minutes. Get medical attention. If swallowed, get medical attention immediately. If inhalation causes discomfort, remove to fresh air. If discomfort persists or breathing
difficulty occurs, get medical attention. KEEP FROM FREEZING. DS396-0211
FREIGHT CLASSIFICATION:
Paint, Freezable
PACKAGING:
1 gallon (3.785 L)
5 gallon (18.925 L)
FLASH POINT:
None
SURFACE PREPARATION
GENERAL SURFACE PREPARATION: All surfaces must be
sound, dry, clean and free of oil, grease, dirt, rust, mildew, form
release agents, curing compounds, loose and flaking paint and other
foreign substances. Glossy surfaces must be dulled by sanding to
ensure proper adhesion. Remove sanding dust. Fill all cracks and
nail holes with spackle and spot prime with this product. For best
results, prime heavily stained areas or watermarks with a stain
blocking primer.
NEW SURFACES: Drywall - Joint compound must dry for two
days before priming. Dust clean. Prime new drywall with this
product. Concrete, Masonry and Plaster - Cure at least 30
days before painting. pH must be 10.0 or lower. Roughen slick
poured or precast concrete and remove sealers by chemical cleaning
or abrasive method such as sandsweeping. Rinse thoroughly with
water and allow to dry. Must be internally dry. Remove loose
aggregate. Prime any bare areas with this product. Fill concrete
block with a latex block filler. Wood - Set nails, fill with latex
spackle. Sand smooth. Dust clean. Prime bare wood with this
Page 2 of 2