GW-90-GH-46-34.
B A H G C x6 x6 I D x2 E F J Included in your purchase Shipped in 5 separate boxes A B C Hinge panel Door panel Fixed panel D E F G Sweep (fixed panel) Sweep (door panel) 45° rod, screw and anchor Door handle H I J Clips, screws and anchors Hinges and hinge screws Rubber block set (various sizes)
Thank you for your purchase. If for any reason you are having trouble with installation, or if the size of the product does not fit your designated space, please contact Glass Warehouse directly and do not return this product to place of purchase. We will be able to exchange the panels or parts to suit your opening. Glass Warehouse takes pride in providing quality products and customer service. We want to ensure your happiness with your purchase for years to come.
Installation Guide 1⁄8" A B C D E ¼" F G H I J Tools required for install A B C D E Silicone and caulking gun Power drill Phillips head screwdriver Pencil ⅛" drill bit F G H I J ¼" drill bit Utility knife Level Hammer Tape measure Note: Silicone is not provided and will need to be purchased separately. We recommend using a clear, mold resistant silicone which can be purchased at your local hardware store.
Hinge panel wall Fixed return wall 45 33 7/8" ⅞" 70 ¼" 7 ¾" 33 45 ⅞" 7/8" 44 ½" 31" 01 02 Measure and mark the fixed return panel location. Mark the three clip locations. Measure 45 7/8" out from the hinge panel wall. This takes you to the center line of the return panel location. Use a level and mark a line up the wall and along the floor. This is your center line for the clips. A 70 ¼" from the floor, up the vertical line. B 7 ¾" from the floor, up the vertical line.
03 04 Drill the holes for clips to fix to the wall and floor. Fix anchors and clips. Using a ¼" tile drill bit, drill the two marked holes on the fixed return wall. Using a hammer, carefully insert the green wall and floor anchors. Trim any excess from the plug hanging out of hole so your clips can sit flush to wall and floor. If the shower base is tiled, use the same ¼" tile drill bit to drill the third hole on the shower floor. If the shower base is fiberglass, use a ⅛" drill bit for the floor hole.
47 13⁄16" 34 5⁄16" 34 13⁄16" 5⁄16" 47 05 06 Set the fixed panel in place. Measure and mark the hinge panel location. Place the ⅛" rubber block on the floor 3" from the wall. Place the 1⁄16" rubber block inside the floor clip. Rubber blocks are not required in the wall clips. Measure 34 5⁄16" out from the fixed panel wall. This takes you to the center line of the hinge panel location. Use a level and mark a line up the wall and along the floor. This is your center line for the wall clips.
70 ¼" 7 ¾" W–3 ½" 07 08 Mark the three clip locations. Drill holes, fix anchors and clips, then set hinge panel. A 70 ¼" from the floor, up the vertical line. Repeating steps 03, 04 and 05: B 7 ¾" from the floor, up the vertical line. Drill holes in new locations. Carefully use a hammer to insert anchors, then screw clips in place. C Measure the width of the hinge panel and subtract 3 ½".
D+¼" 09 10 Ensure both panels are level and correctly spaced. Install the 45° rod. Optional for additional support. Using a level, check the top of both panels are level and equal height from the floor. If a panel(s) isn't level, use additional rubber blocks to correct it. Loosen the allen bolt inside the clip and place on top of the hinge panel. Position the 45º rod so the other end is flush with the wall. Mark position of screws on the wall before removing the rod.
11 12 Apply silicone to seal both panels. Attach the hinges to the hinge panel. Trim the rubber blocks with a utility knife so that they are flush with the glass panels resting on top of them. Slide the solid plate side of the hinge in to the hinge panel cutout, ensuring the screws face into the shower. Lightly tighten screws. Apply silicone around the wall and floor surface of both panels.
A B C D C B E F G Door panel H H Inside of shower Inside of shower 13 Attach the door handle to the door panel. Place the plastic washers (D) in the door handle holes. Then attach the handle as illustrated above. Important: Ensure the handle is firmly secure so it can be used to lift and maneuver the door in the final steps.
14 15 Set the door panel in place. Tighten hinge screws and you're done. Place two of the ⅜" rubber blocks on the floor between the hinge and fixed panels — 2" from each panel. Put the backing plates on hinges and tighten all four screws on both hinges. Standing inside the shower, carefully place the door panel on the blocks and line up the cutouts with the back of the hinges. Check that the top of all three panels are level. Next, check that vertical gap on either side of the door is even.
Care & Maintenance EnduroShield makes cleaning easier and less frequent; however it is recommended that you continue to clean the surfaces regularly. Maintaining the Treated Surface Approved Cleaning Products For best results simply drying the glass with a squeegee or towel after each use will help keep the glass clean and reduce mineral spots forming.
Exclusive Limited Warranty Terms & Conditions. This warranty is effective as of JANUARY 1, 2019 on all Glass Warehouse product purchases PLEASE READ GLASS WAREHOUSE WARRANTY TERMS AND CONDITIONS BEFORE INSTALLING YOUR GLASS WAREHOUSE PRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS Glass Warehouse offers the following warranty for its products and components thereof.
obligation shall be discharged upon tender of parts, replacement or repair of the product. Purchaser’s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY. Cost of freight for returning products to Glass Warehouse for repairs or replacement under this limited warranty are the responsibility of the customer. Cost of freight associated with shipping of replacement product(s) or parts covered by this warranty is the responsibility of the original user.
Register Your Warranty Today! To activate your limited lifetime warranty, please visit: http://www.glasswarehouse.us/contact/ We will require this information within 30 days of purchase to complete the activation of your warranty.
