2DSL 56"- 60" Shower Enclosure Installation Guide Polaris Square Double Slider Shower Enclosure
Thank you for your purchase. If for any reason you are having trouble with installation please contact Glass Warehouse directly. Glass Warehouse takes pride in providing quality products and customer service. We want to ensure your happiness with your purchase for years to come. If you have any questions, please do not hesitate to reach out to us. Thank you again for choosing Glass Warehouse! Best Regards, The Team at Glass Warehouse Glass Warehouse, LLC (760) 536 3640 inquiries@glasswarehouse.
Installation Guide Before You Start • Measure if your walls are out of plumb. It is essential your shower enclosure is tiled before measuring as your measurements WILL change once tiling and grout are in place. 731⁄8" 731⁄8" Take 3 Tile to Tile Measurements: 1. TOP of rod height (731⁄8") 2. MIDDLE from threshold (39") 39" 3. BOTTOM at threshold 39" If your walls are 3⁄8" or more out of plumb, please contact Glass Warehouse before installing.
73 1⁄8" 73 1⁄8" Minimum 1 1⁄2˝ (38 mm) from edge Middle of Shower opening 01 02 03 04 Mark threshold and walls for Shower Rod position Mark location of Shower Rod Brackets Mark drill holes for Shower Rod Brackets Mark drill holes for Bottom Bracket Measure the width of threshold tile where shower door is to be installed, this needs to be a minimum of 3" to install this model shower enclosure. Measure to center of threshold and mark a line down the center.
05 06 07 08 Drill Holes for Shower Rod Brackets Drill holes for Bottom Bracket Install Shower Rod Brackets Install Bottom Bracket Using a 1⁄4" drill bit, drill holes and install the wall anchors. Trim excess from the wall anchors hanging out of hole with utility knife so Shower Rod Brackets sit flush to the wall. Using a 1/4" drill bit, drill 2 holes and install anchor (if necessary). Trim excess from the anchor with utility knife. Fill the holes with silicone to waterproof.
591 ⁄2˝ 55 1⁄2˝ Shower Rod Max Width: 59 1 ⁄2˝ Min Width: 55 1⁄2˝ 55 1 ⁄2˝ 591⁄2˝ 73 1⁄8" 73 1⁄8" 09 10 11 12 Measure Shower Rod for cutting Cut Shower Rod at both ends Install Sliding Panel Stoppers Install Shower Rod into Shower Rod Brackets Prior to Shower Rod installation, position Sliding Panel Stoppers on each end of Shower Rod with rubber bumpers facing back edge of sliding glass door panels in open position. Secure in place after Shower Rod is installed.
Install with flat area parallel to top of door panel Interior plate 4x Exterior cover plate Use pliers to adjust Spanner Wrench Spanner Wrench Open End Wrench Attach sweeps with lips facing towards shower interior 13 14 15 16 Install Shower Rod Bracket Top Covers Unpack and disassemble 4 sets of Rollers Install Top Rollers on both sliding doors Install Bottom Sweeps on both sliding doors Once Shower Rod is perfectly level, insert Top Covers back into the Shower Rod Brackets and use the set s
17 18 19 20 Hang Interior Door Panel Install Bottom Rollers on Interior Panel Adjust Wheel Positions snug to Shower Rod Hang Exterior Door Panel Lift the Interior Door Panel and slowly lower the rollers onto the Shower Rod. When lowering the Door Panel, be sure the bottom of Door Panel slides into the Bottom Bracket and the Sweep faces the interior of the shower. Gently slide Door Panel from side to side making sure it is not binding anywhere along the bottom.
21 22 23 24 Install Bottom Rollers on Exterior Panel Adjust Wheel Position snug to Shower Rod Position and secure Stoppers Prepare Towel Bar Handles for installation Prepare 2 Bottom Rollers by removing Exterior Plate. Using Spanner Wrench and Open Ended Wrench, adjust wheel position to make Bottom Roller snug to Shower Rod. Reinstall Exterior Cover Plates to all 4 Rollers. Open each Door Panel to maximum open position. Once in maximum open position, tighten each Stopper in place.
Remove adhesive backing 775⁄8" Remove adhesive backing 25 26 27 28 Install Towel Bar Handles on Glass Panels Trim the L-shaped Seals Attach L Seals on wall side of each Door Panel Install the L-shaped Seals Reinstall hardware on to Door Panels as shown above. Interior Door Panel will have Towel Bar on the inside of the shower. Exterior Door Panel will have Towel Bar on the exterior of shower. Tighten completely using allen wrench in the hole on mounting post.
Care & Maintenance EnduroShield makes cleaning easier and less frequent; however it is recommended that you continue to clean the surfaces regularly. Maintaining the Treated Surface Approved Cleaning Products For best results simply drying the glass with a squeegee or towel after each use will help keep the glass clean and reduce mineral spots forming. The glass needs to be cleaned every few weeks using a damp microfiber cloth and a mild detergent to break down soaps, oils, and conditioners on the glass.
Exclusive Limited Warranty Terms & Conditions. This warranty is effective as of JANUARY 1, 2024 on all Glass Warehouse product purchases. PLEASE READ GLASS WAREHOUSE WARRANTY TERMS AND CONDITIONS BEFORE INSTALLING YOUR GLASS WAREHOUSE PRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS Glass Warehouse offers the following warranty for its products and components thereof.
Register Your Warranty Today! To activate your limited lifetime warranty, please visit: https://www.glasswarehouse.us/contact/ We will require this information within 30 days of purchase to complete the activation of your warranty.
