Installation Guide
J
Installation (continued)
NOTE: The hot side inlet tube is indicated by
a label. Avoid twisting wires together or placing
7
Attaching the quick connector to
the receiving block
9
Making the water supply
connections
8
Installing the weight
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Attaching the quick connector
to the receiving block
7 8
9
Installation (continued)
9
18
Weight
here
20
20
19
19
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
Attaching the quick connector
to the receiving block
7 8
9
Installation (continued)
9
18
Weight
here
20
20
19
19
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
Install the weight clip (20) at the point of the hose marking
“weight here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Attaching the quick connector
to the receiving block
7 8
9
Installation (continued)
9
18
Weight
here
20
20
19
19
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
W
eight
he
r
e
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con 1-855-HDGLACIER para obtener más asistencia.
4
Cómo instalar el ensamblaje del grifo
Instalación por arriba (continuación)
5
Cómo fijar el ensamblaje del grifo
9
Installation (continued)
7
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
5
Securing the faucet assembly
6
Installing the sink
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount™ system (21). Push the Fastmount™
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
5
7
6
Installation (continued)
Securing the faucet assembly
Installing the sink
rotate the clips
21
Sink
Push
up
21
1 1
Push
up
21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount
TM
system (21). Push the Fastmount
TM
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
rotate the clips
5
7
6
Installation (continued)
Securing the faucet assembly
Installing the sink
rotate the clips
21
Sink
Push
up
21
1 1
Push
up
21
2
3
3
Sink
21
Sink
Continue to push up
and turn clockwise
to tighten
From underneath the sink, secure the faucet assembly to the
sink with the Fastmount
TM
system (21). Push the Fastmount
TM
system (21) up over the threads until it stops against the
bottom of the sink, then hand turn (clockwise) to tighten.
Apply silicone sealant (not included) around the underside and lip of the sink (A).
Carefully lower the sink (A) into the counter.
Rotate the clips. Tighten the screws on the top mount clips (AA) evenly until the
sink (A) is flush with the counter. Do not overtighten.
Wipe excess sealant with a rag.
Push
up
Sink
Push
up
Sink
Sink
Continue to push up
and turn clockwise
to tighten
Empu-
jar
Frega-
dero
Fregadero
Continúe empujando
hacia arriba y gire
en sentido horario
Empu-
jar
Frega-
dero
6
Cómo montar el conector rápido al
bloque receptor
7
Instalar la peso
Weight
here
Weight
here
20
20
19
19
Cierra el suministro de agua.
Coloca el ensamblaje del grifo (J) en el orificio
del fregadero.
PRECAUCIÓN: Cierra siempre el suministro de agua antes de retirar un
grifo existente o reemplazar alguna parte del mismo. Abre la llave del grifo
para liberar la presión de agua y asegúrate de que el suministro de agua esté
completamente cerrado.
Desde abajo del lavamanos, asegura el conjunto del grifo a aquel
con la sistema FastMountTM (21). Empuja la sistema
FastMountTM (21) hacia arriba sobre las roscas hasta que toque la
parte inferior del lavamanos. Enseguida gírala con la mano (hacia
la derecha) para ajustar (Fig. 1).
Instala el sujetador de la peso (20) en la punta de la manguera
marcada “weight here” (peso aquí).
Inserta la peso (19) en el sujetador (20)
deslizándola en el sujetador (20).
Presiona firmemente el conector rápido (18) hacia arriba y fíjalo en
el bloque receptor (9). Hala hacia abajo ligeramente para asegurar
que la conexión es segura.