Installation Guide

ManualsBrandsGlacier Bay ManualsBathLucien Toilet Paper Holder in Matte Black

Phillips

screwdriver

Claw

hammer

TOOLS REQUIRED

Electric drill Pencil

HARDWARE INCLUDED

Installation

HOMEDEPOT.COM/GLACIERBAY

Please contact 1-855-HD-GLACIER for further assistance.

Determining the mounting

location

Drilling the pilot hole

1 2

Determine the location where you wish to

install your accessory.

Place the mounting bracket (B) at the desired

location and mark the installation holes using

a pencil.

Pre-drill a pilot hole with a small drill.

Safety Information

If installing into ceramic tile, before attempting

to drill through ceramic tile, the following must

be done:

Using a center punch, very lightly and carefully

tap the spot where you wish to drill to break

the shiny glass portion of the tile.

A- Self-drilling

drywall anchor

B- Mounting bracket

C- Mounting screw

D- Hex wrench

E- Set screw

F- Solid wall anchor

Installing the bracket in

drywall

3.1

Drill a 1/8 in. based on the pre-drill pilot hole.

Drive the drywall anchor (A) into the wall using

a Phillips screwdriver until ush with the wall.

Align the mounting brackets (B) with the

drywall anchor (A) and secure with the

mounting screws (C).

Installing the bracket in

wood stud

Drill 3/32 in. based on pre-drilled pilot hole.

Align the mounting brackets (B) with pilot

holes and secure with the mounting screws

(C).

NOTE: To install the brackets (B) in a wood

stud, proceed to Step 3.2. To install the

brackets (B) in ceramic tile, proceed to Step 3.3.

3.2

USE AND CARE GUIDE

PAPER HOLDER

Item #100-483-3712

Model #BTH-008-106

Summary of content (4 pages)

PAGE 1
Item #100-483-3712 Model #BTH-008-106 USE AND CARE GUIDE PAPER HOLDER TOOLS REQUIRED Phillips screwdriver HARDWARE INCLUDED Electric drill Pencil Claw hammer A- Self-drilling drywall anchor x2 B- Mounting bracket x1 C- Mounting screw x2 D- Hex wrench x1 E- Set screw x1 F- Solid wall anchor x2 Installation the mounting 1 Determining location Determine the location where you wish to install your accessory.
PAGE 2
Installation (continued) the bracket in 3.3 Installing ceramic tile the bathroom 4 Installing accessory Drill a 1/4 in. based on the pre-drill pilot hole Tap 1/4 in. solid wall anchors (F) into the wall with a hammer until flush with the wall. Align the mounting brackets (B) with installed solid wall anchors (F) and secure with the mounting screws (C). Position the bathroom accessory over the mounting bracket (B) using the set screw (E). Tighten securely with the Hex wrench (D).
PAGE 3
Núm. de artículo 100-483-3712 Núm. de modelo BTH-008-106 GUÍA DE USO Y CUIDADO PORTARROLLOS HERRAMIENTAS REQUERIDAS SE INCLUYE LOS HARRAJES A- Anclaje autoperforante para paneles de yeso x2 Destornillador Phillips Taladro elécrico Lápiz Martillo de orejas D- Llave hexagonal x1 B- Soporte de montaje x1 E-Tornillo de presión x1 C-Tornillo de montaje x2 F-Sujetador para pared maciza x2 Installation 1 Elección del lugar de montaje Elija el lugar donde desea instalar el accesorio.
PAGE 4
Instalación (continuación) de accesorios 3.3 Instalación para el cuarto de baño de accesorios 4 Instalación para el cuarto de baño Taladre 1/4 pulg. sobre la base del agujero piloto pretaladrado. Introduzca en la pared los sujetadores murales (F) con un martillo hasta que estén a nivel con la pared. Alinee el soportes de montaje (B) con los sujetadores murales (F) y sujete el soporte con los tornillos de monteje (C).