User Manual

ManualsBrandsGilbar ManualsElectronicsPoint of Sale Mat Reader System

MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001 Page 1

eli

05/

24/

Introduction

Purpose of this Manual

This manual provides instruction for installing TIRIS™

Mat Reader Assembly Kit C00016-

XXX.

The TIRIS™ option allows customers to automatically authorize non-cash sales using a hand-

held transponder tag.

Important Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy, and if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense. Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate this equipment.

The long term characteristics or the possible physiological effects of radio frequency

electromagnetic fields have not been investigated by Underwriters’ Laboratories, Inc. (UL

Required Reading

Before installing the equipment, the installer must read, understand, and follow:

• this manual

• NFPA 70, The National Electric Code

• applicable federal, state and local codes and regulations

Failure to do so may adversely effect the safe use and operation of the equipment.

MDE-4017

TIRIS™ Transmitter/Receiver Mat Reader

Assembly Kit C00016-XXX Installation

May 2001

Summary of content (14 pages)

PAGE 1
MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation May 2001 Introduction Purpose of this Manual This manual provides instruction for installing TIRIS™ Mat Reader Assembly Kit C00016XXX. Pr el 05 im /2 i 4/ n 01 a ry The TIRIS™ option allows customers to automatically authorize non-cash sales using a handheld transponder tag.
PAGE 2
Related Documents Installer must obtain, read and understand all site preparation documentation provided by the point of sale company authorizing the installation before attempting to install this equipment. In addition, the installer must be familiar with the information in the following documents.
PAGE 3
Important Safety Information This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found. Electrical shock could occur and cause death or serious injury if these safe service procedures are not followed.
PAGE 4
Safety Symbols and Warning Words Alert Symbol This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazards. Obey safety directives that follow this symbol to avoid possible injury or death. Signal Words Pr el 05 im /2 i 4/ n 01 a ry These signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards.
PAGE 5
Installation Note: All installation work is to be accomplished between the hours specified by the point of sale company authorizing the installation. Install Mat Reader assembly according to the following: 1 Collect and arrange all tools and equipment. 2 If necessary for installation of kit in area specified by point of sale company, remove advertisement panels, saving all mounting hardware for re-use later.
PAGE 6
3 Set the jump jacks as follows (see “Figure: Jump Jacks for Baud Rate Setting” on page 5). CAUTION Electrostatic Discharge Damage Working on electronics without connecting to a ground or discharging static can damage electronic parts. Use a wrist strap.
PAGE 7
3 Note position of jump jacks on previously installed Mat Reader logic board, and set jump jacks on board for Mat Reader being installed to match address on logic board. CAUTION Electrostatic Discharge Damage Working on electronics without connecting to a ground or discharging static can damage electronic parts. Use a wrist strap.
PAGE 8
Mounting Mat Reader Interface Box 1 Determine the location for the installation of indoor equipment. Note: Refer to site prep document provided by point of sale company and keep in mind overall length of cable to connect Mat Reader Interface Box to Mat Reader. 2 Use a Zircon stud/bracket finder to ensure no electrical conduits or pipes are located inside of wall where the Mat Reader Interface Box is to be mounted.
PAGE 9
Connecting Data Cables to Mat Reader Interface Box Run both power and data cables to port end of Mat Reader Interface Box (see “Figure: Mat Reader Interface Box Mounting Holes” on page 8) as follows. 1 Connect the P3 end of the ribbon cable (M01872A001) to the RFID interface port (P3) . 2 Connect the J1end of the CAT-5 cable (Q13482-06) to the J1IN port. Connect power supply here. Connect J1 end of CAT-5 cable here.
PAGE 10
Connecting Data Cables from the Mat Reader Interface Box 1 Position Mat Reader face down. Figure: Bottom Side of Mat Reader bottom side of neoprene foam tape (flipped over to show connector) bottom side of Mat Reader Pr el 05 im /2 i 4/ n 01 a ry 7-pin connector channel for ribbon cable (acrylic foam tape in place) 2 Select side for ribbon cable (M01872A001) connection based on counter top configuration requirements.
PAGE 11
Figure: Connecting to Mat Reader bottom side of neoprene foam tape y ribbon cable connected to 7pin connector ar unused channel filled with plastic filler channel and covered by neoprene foam tape 6 Install neoprene foam tape (M01870B001) over ribbon cable and sides of channel. Foam tape in should fit snugly into cutout of surrounding foam tape backer. 05 /2 4/ 01 7 On unused cable channel, install plastic filler channel (M01871B001).
PAGE 12
Connecting Power Supply Connect the power supply (M01878B001) provided with kit as shown. 1 Plug the wall-mounted transformer into the AC power outlet. Note: This AC power outlet must be on the same circuit as the G-SITE system. 2 Connect the plug end of the power supply cable to the JDC1 port on the Mat Reader Interface Box (see “Figure: Connecting to Mat Reader Interface Box” on page 9).
PAGE 13
Completing Installation Figure: Mat Reader Connections power supply interface box CAT-5 cable connects here 05 /2 4/ 01 ribbon cable in ar y Mat Reader im 1 Dress all cables and secure with stick on cable clamps (Q13459-01). 2 Clean up the work area. Pr el 3 Go to “Commissioning and Warranty Information” on page 14.
PAGE 14
Commissioning and Warranty Information Upon completion and testing the Mat Reader system, the installing contractor must call the Marconi Commerce Systems Call Center @ 1-888-800-7498 to register the installation and activate the warranty. Note the installed unit’s full Model Number (C00016-XXX) and serial number before making this call. • All Mat Readers have a one-year parts only warranty. Note: Parts are to be returned through and obtained from the local Marconi distributor.