Certification Exhibit FCC ID: N6SLFMAT IC: 827B-LFMAT FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0278 Manufacturer: Gilbarco Inc. Models: C00016-011, C00016-010 Manual 5015 B.U.
MDE-4017E Mat Reader Assembly Kit C00016-XXX Installation Manual June 2013 Introduction Purpose This manual provides instructions for installing the Mat Reader Assembly Kit C00016-XXX on the Passport System. The Mat Reader allows customers to automatically authorize sales using a hand-held transponder tag (also known as a keytag).
Introduction Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Introduction Following table lists the parts included in the C00016-011 Kit - Low Frequency [Personal Identification Number (PIN) Pad]: Part Number Quantity M01814A001 1 Cable, Mat Reader Drive 6 feet (1.8 m) M01872A002 1 Ferrite, Snap-on Q11433-107 1 Ferrite, Clip-on Q11433-110 2 Power Supply, Wall-mount M01878B001 1 Jack, Jump Q11011-01 1 Clamp, Flat Cable, Stick On, Small Q13459-01 1 Cable, Data, CAT-5, 6 feet (1.
Introduction Abbreviations and Acronyms Description ASC Authorized Service Contractor CRT Cathode Ray Tube CWS Cashier Workstation e.i.r.p Equivalent Isotropically Radiated Power EMC Electro-magnetic Compatibility FCC Federal Communications Commission IC Integrated Circuits MWS Manager Workstation NEC National Electric Code NFPA National Fire Protection Association p.i.r.
Important Safety Information Important Safety Information Notes: 1) Save this Important Safety Information section in a readily accessible location. 2) Although DEF is non-flammable, Diesel is flammable. Therefore, for DEF cabinets that are attached to Diesel dispensers, follow all the notes in this section that pertain to flammable fuels. This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining, or servicing this product.
Important Safety Information In an Emergency No Open Fire Open flames from matches, lighters, welding torches, or other sources can ignite fuels and their vapors. No Sparks - No Smoking Sparks from starting vehicles, starting, or using power tools, burning cigarettes, cigars, or pipes can also ignite fuels and their vapors. Static electricity, including an electrostatic charge on your body, can cause a spark sufficient to ignite fuel vapors.
Installing Mat Reader Assembly Installing Mat Reader Assembly CAUTION Gilbarco strongly recommends that only Gilbarco Authorized Service Contractors (ASCs) perform this installation. Note: All installation work is to be accomplished between the hours specified by the Point of Sale (POS) company authorizing the installation. To begin installing the Mat Reader Assembly, collect and arrange all tools and equipment for safety and convenience.
Installing Mat Reader Assembly Interface Box For optimum Mat Reader performance, the interface box should be positioned as close to the Mat Reader as is conveniently possible. If necessary, the CAT-5 Cable (Q13850-06), may be swapped out for a longer version in order to properly place the interface box and still reach the POS connection. The dash number, such as -06, indicates 6 feet (1.8 meters) long.
Installing Mat Reader Assembly 2 Locate Jump Jacks on Logic Board for Mat Reader (see Figure 2). P re lim in ar y Figure 2: Jump Jacks for Baud Rate Setting on Logic Board 3 Set the Jump Jacks as follows (see Figure 2). CAUTION A properly grounded ESD wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty.
Installing Mat Reader Assembly Mounting and Connecting Mat Reader Interface Box To mount and connect Mat Reader Interface Box, proceed as follows: 1 Mount the Mat Reader Interface Box following the procedures in “Mounting Mat Reader Interface Box” on page 29. 2 Run both power and data cables to port end of Mat Reader Interface Box (see Figure 3) as follows: a Connect the J3 end of the Ribbon Cable (M01872A001) to the interface P3 Port. b Connect the P1 end of the CAT-5 Cable to the J1IN Port.
Installing Mat Reader Assembly 4 Select side for Mat Reader Drive Cable (M01872A002) connection based on countertop configuration requirements. Note: The Mat Reader is designed to be placed on a countertop beside or adjacent to a cash register or POS terminal. If properly positioned, the Mat Reader cable will “disappear” underneath the existing POS equipment. The cable will penetrate the countertop via the same hole used by the POS power and data cables.
Installing Mat Reader Assembly 8 Gently turn the Mat Reader to the face-up position (see Figure 6). re lim in ar y Figure 6: MR01003Gxxx Mat Reader - Face Up 9 Connect the loose end of the CAT-5 cable to the POS system. • For a Passport system, the Mat Reader connects to P3 Port on the USB converter using a Q13180-20B Gender Mender. Refer to MDE-4157 Passport Combined WS Installation Poster, MDE-4158 Passport Cashier WS Installation Poster, and MDE-4159 Passport Manager WS Installation Poster.
Installing Mat Reader Assembly 3 Double loop the JDC1 end of the Power Supply Cable through the Ferrite Bead (Q11433-107) with the bead in the open position, then snap the bead shut (see Figure 8).
Installing Mat Reader Assembly 2 Dress all cables and secure with stick on Cable Clamps (Q13459-01). 3 Clean up the work area. 4 Ensure the keytag is read by the Mat Reader within the specified range (see Figure 11). re lim in ar y 2.0 - 4.0” (5 - 10 cm) Figure 11: Verifying Low Frequency Mini Mat Reader P 10 Go to “Commissioning and Warranty Information” on page 30.
Installing Mat Reader Assembly Figure 12: Mat Reader Interconnect/Block Diagram M01873 (Sheet 2 - Mini Mat) In Mat Reader Assembly (MR01003GXXX) P re lim in ar y In Interface Box Assembly (M01814A001) +12VDC 115VAC DC MDE-4017E Mat Reader Assembly Kit C00016-XXX Installation Manual · June 2013 Page 15
Installing Mat Reader Assembly Installing C00016-011 Kit - Low Frequency (PIN Pad) To install C00016-011 Kit - Low Frequency (PIN Pad), proceed as follows: Setting Baud Rate The set the Baud Rate, proceed as follows: 1 Remove the Mat Reader Interface Box cover to access the Logic Board (M01803A001) as shown in Figure 13. Figure 13: Mat Reader Interface Box Cover Screw re lim in ar y Cover Logic Board P 2 Locate Jump Jacks on Logic Board for Mat Reader (Figure 14).
Installing Mat Reader Assembly 3 Set the Jump Jacks as follows (see Figure 14 on page 16). CAUTION A properly grounded ESD wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty.
Installing Mat Reader Assembly c For daisychaining interface boxes, connect a CAT-5 Cable from the J2OUT Port on this interface box to the J1IN Port on the other interface box.
Installing Mat Reader Assembly 10 Gently slide the PIN Pad down the Pedestal/PIN Pad Adapter Plate/pin Pad Mat Reader combination so that the screws fit firmly into the slot holes. 11 Tighten the screw on the bottom of the angled plate on the pedestal to lock the Pedestal/PIN Pad Adapter Plate/PIN Pad Mat Reader combination in place. For PIN Pad and Mat Reader Assembly, see Figure 19 on page 20. 12 Connect the loose end of the CAT-5 Cable from the interface box to P3 Port on the USB converter.
Installing Mat Reader Assembly Figure 18: Screw Head Height Above PIN Pad Mat Reader Screw PIN Pad Mat Reader 0.160” (4 mm) PIN Pad Adapter Plate Pedestal Top re lim in ar y Figure 19: PIN Pad Mat Reader Assembly on Pedestal PIN Pad Mat Reader - With Pedestal and Without Hole in Countertop P Note: The pedestal will serve as support for the PIN Pad and Mat Reader.
Installing Mat Reader Assembly 7 Place the three Q11270-38 Screws through the corresponding holes in the PIN Pad Mat Reader and the adapter plate, and screw into the corresponding holes in the pedestal leaving the screw heads 0.160 inches (4 mm) above the top of the PIN Pad Mat Reader. 8 Align the three mounting holes on the bottom of the PIN Pad over the three screws on the pedestal/PIN Pad Adapter Plate/PIN Pad Mat Reader combination.
Installing Mat Reader Assembly PIN Pad Mat Reader - Without Pedestal and Hole in Countertop To install the PIN Pad Mat Reader without pedestal and hole in countertop, proceed as follows: Note: The PIN Pad Cable (supplied with PIN Pad) and Mat Reader Drive Cable ((M01872A002) are routed between the Mat Reader and PIN Pad. The four Rubber Bumpers (Q12226-01) are attached to the back of the PIN Pad Adapter Plate (M03182B001) to keep it off the countertop.
Installing Mat Reader Assembly 13 Connect the loose end of the CAT-5 Cable from the interface box to P3 Port on the USB converter. Refer to MDE-4157 Passport Combined WS Installation Poster, MDE-4158 Passport Cashier WS Installation Poster, and MDE-4159 Passport Manager WS Installation Poster.
Installing Mat Reader Assembly Connecting Wall-mount Power Supply (M01878B001) To connect the Wall-mount Power Supply provided with kit as shown in Figure 24, proceed as follows: Figure 24: Wall-mount Power Supply Plugs into JDC1 Port Plugs into AC Power Outlet re lim in ar y Wall-mounted Transformer 1 Plug the wall-mounted transformer into the AC power outlet. Note: This AC power outlet must be on the same circuit as the POS system.
Installing Mat Reader Assembly Figure 27: Ferrite on Interface Cables Ferrite on Interface Cables P re lim in ar y 2 Dress all cables and secure with stick on Cable Clamps (Q13459-01). 3 Clean up the work area. 4 Verify the keytag can be read by the Mat Reader within the specified range (see Figure 28). Figure 28: PIN Pad Mat Reader Read Verification PIN Pad PIN Pad Adapter Plate (M03182B001) 2.0 - 4.
Installing Mat Reader Assembly Figure 29: Mat Reader Interconnect/Block Diagram M01873 (Sheet 3 - PIN Pad) In Mat Reader Assembly P re lim in ar y In Interface Box Assembly +12VDC 115VAC DC Page 26 MDE-4017E Mat Reader Assembly Kit C00016-XXX Installation Manual · June 2013
Installing Mat Reader Assembly Addressing Logic Board When Daisychaining Address for Mat Reader must match address on previously installed Mat Reader. To set the address on Logic Board when daisychaining, proceed as follows: 1 Access Logic Board for Mat Reader being installed. 2 Locate Jump Jacks on previously installed Mat Reader Logic Board M01803A001 or M01803A002 as appropriate (see Figure 30 or Figure 31).
Installing Mat Reader Assembly CAUTION A properly grounded ESD wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty.
Installing Mat Reader Assembly Mounting Mat Reader Interface Box To mount the Mat Reader Interface box, proceed as follows: 1 Determine the location for the installation of indoor equipment. The interface box may be mounted under the countertop (upside down) or vertically on one of the supporting walls of the countertop. Note: For connecting Mat Reader Interface Box to Mat Reader, refer to MDE-3620 Gilbarco POS Console Site Preparation Manual. Also refer to “Interface Box”on page 8.
Commissioning and Warranty Information Commissioning and Warranty Information Upon completion and testing the Mat Reader system, call the Gilbarco Call Center at 1-888-800-7498 to register the installation and activate the warranty. Note: The installed unit’s full model (C00016-XXX) and serial number are required to register the installation and activate the warranty. • All Mat Readers have one-year parts warranty. Note: Parts are to be returned through and obtained from the local Gilbarco distributor.
