Poseidon GZ-XA1CA-STB GZ-XA1CA-STS User’s Manual 20070301-GZXA1CA-STBSTS rev.
Poseidon Introduction The chassis of Gigabyte Poseidon series is made by high-end Aluminum bezel design with dual 12cm (front and rear) silent fans to offer the best ventilation for the system. The internal cable management and tool-free design provide users with easer installation procedures and computer system management. Using the patent 2 colors front projector light with changeable LED colors (blue/white) and the see-through/air inlet side panel, users can customize their own style.
Contents 1 Components Introduction ..................................................................................................... 4 1-1 Chassis’s Internal Structure ............................................................................. 4 1-2 Side Panel Introduction .................................................................................... 6 1-3 Front and Rear Panel Instruction ..................................................................... 7 2 Features.......................
English 1 Components Introduction English 1-1 Chassis’s Internal Structure English 1 4 3 English 5 6 2 7 1 Power supply 2 PCI tool-free fastener 3 Motherboard/panel card 4 5.
6 3.5” Floppy English 5 Build-in hard disk English 7 Accessory box d. Wire clamp x 1 c. Motherboard securing screw x 9 e. Power supply securing screw x 4 f. Magnet ring x 1 English g. DIY transparent projector panel x 1 (Equipped with Poseidon at shipment) (Refer to the right figures for the attachments in the tool enclosure) 8 b. Securing runner x 6 English a. Standoff x 9 Front cable kit b. HD AUDIO Deutsch a.USB 2.0 c.
English 1-2 Side Panel Introduction English See-through side panel installation complete figure (A-1) English (Factory default: vent side panel) 1-2-1 To replace the See-through side panel: Deutsch Step 3: Draw out the perforated side panel. English Step 2: Remove the factory default perforated side panel. Deutsch English Step 1: Release 4 screws at the rear of the side panel to remove the panel.
English 1-3 Front and Rear Panel Instruction 1-3-1 To remove front panel: Step 1: Remove the left and right side panels ( see Step 1-2-1 on Page 6) and slightly pull out both sides of the upper (see, Figure a) and lower (see Figure b) fasteners (see Figure c).
English English English English Deutsch Deutsch English 2 Features - High quality design - Integration of cooling technology (Patent Pending)Customizable light beam (Patent pending)Integrated side panel projector w/ changeable LED color (Blue/White) (See-through & elegant vent design) Hign-end Aluminum bezel design Quad-ways front air-inlet design Skidproof & shockproof foot stand - Complete support Front bezel I/O (USBx2,IEEE1394x1, HD audiox1) Dual 12cm silent & shockproof fan (Rear fan w/ LED) Support
English 4 Installation Instruction Please follow the reference sections for installation. To facilitate the installation, it is recommended to place the Poseidon chassis upright on the table. Required tool: Power supply securing screw x 4. English 4-1 Installation of Power Supply 4-1-1 Please remove the left side panel before placing the power supply into the chassis. English English 4-1-2 Use screws to secure the power supply from the rear side.
English The Poseidon supports tool-free installation of interface cards, e.g. Graphic card and Network Card, etc. Required tool: None 4-3-1 Unlock securing fasteners of the PCI socket; push the fastener downwards first. English English 4-3 Installation of Interface Card English 4-3-2 And then, push the fastener upwards. Deutsch 4-3-3 Remove the internally attached dust-proof PCI cover. Deutsch 4-3-4 Insert the interface card into the expansion slot with care.
The front panel consists of (1) Two USB 2.0 ports, one IEEE 1394, and one High Definition Audio connector. (2) Basic chassis power switch control cable kit USB 2.0 Connector Definition Power Power USB DxUSB DyUSB Dx+ Pin 6 7 8 9 10 Definition USB Dy+ GND GND English Pin 1 2 3 4 5 English Required tool: None (1) Two USB 2.0 ports, one IEEE 1394, and one High Definition Audio connector. 4-4-1 Insert the USB2.0 connector into the corresponding socket on the motherboard.
English English English 4-4-3 Attach the HD Audio connector to the pin located on the motherboard. Pin 1 2 3 4 5 6 7 8 9 10 Definition MIC2_L GND MIC2_R -ACZ_DET Line2_R FSENSE1 FAUDIO_JD No Pin LINE2_L FSENSE2 Pin 1 2 3 4 5 Definition MIC GND MIC Power NC Line Out (R) Pin 6 7 8 9 10 Definition NC NC NO Pin Line Out (L) NC Follow the connectors listed below for installation (see the figure below). Connector Speaker Reset SW Power SW POW LED+ POW LEDH.D.D.
The installation of 5.25” CD-ROM is also intended for installation of general 5.25” front device bay. Required tool: None English 4-6-1 Remove the front panel (see Step 1-3-1 on Page 7) and take off the 5.25” internal metallic panel. English 4-6 Installation of 5.25” Front Device Bay 4-6-2 Slide the 5.25” CD-ROM into the drive. English English 4-6-3 Refer to the installation order illustrated in the left figure and secure the 5.25” CD-ROM by controlling the latch.
English English 4-7-4 Installation completed. English 4-7-3 Refer to the installation order illustrated in the left figure and secure the 3.5” floppy disc drive by controlling the latch. (Reverse steps for disassembly) The Poseidon built-in HD drive bay can be installed with up to 3 HDDs. The built-in HDD requires securing runners, which are located in the accessory box below.
The Poseidon is provided with another transparent projector panel, which can be DIY designed and replaced with the projector bracket under front panel. Required tool: transparent projector panel (slides and laser printer or copy machine should be provided by the user) English Print out the slides by 1:1 (Please use the laser printer or copy machine) English 4-10-1 Please visit Gigabyte website (http:// gwebmanager1:7001/Products/Chassis/Default.
English 4-10-6 There is a switch for changing the color of projection lamp on the case; the right side is blue and the left side is white. English White Blue (Factory default) English 4-10-7 Place the completed transparency plate on the bottom position of the front panel and refit the front panel. 4-11 Foot Stand Instruction The Poseidon is supplied with four skid-proof foot stands for ensuring the chassis is firmly seated on the holding surface. 4-11-1 High-end skid-proof food stand.
English 4-12 Liquid Cooling System Support The Poseidon series chassis can fully support the Gigabyte 3D Galaxy Liquid cooling kit (also support most of the liquid cooling systems commercially available). While installing the liquid cooling system, please consult its manual first. 4-13 Recommended Air Cooling English The Poseidon is recommended to be used with the Gigabyte Air Cooling series.
English Deutsch Deutsch English English English English
