Owner's Manual
The following are not covered by the warranty :
1. Use the product incorrectly or in a manner other than the designed
purpose.
2. Nonobservance of the proper operation provided. (e.g. over-clocking)
3. Malfunction due to interference from other devices.
4. Fail to install due to the specication of the VGA card or other
components that are not supported by the product.
5. Unauthorized modication of the product.
6. Malfunction arising from casualties (earthquake, thunder, re, and
ood).
7. The warranty label of the product has been removed or damaged.
8. Any loss caused by removing the original heat sink on VGA card.
9. Any loss caused by failure to follow the installation process contained
in the user.
GH-UD UE2 1-F C
Caution
Features
1. Supports nVIDIA SLi and ATi CrossFire.
2. High Performance – Aluminum n with copper
pillar and base to advance thermal circulation.
3. Radial airow – 8 cm fan with radial airow to
enhance thermal circulation of surrounding
components.
4. Light weight – Only 200g, VGA card loading free.
5. Two covers in red and green– Users may use the
cover depend on their preference.
6. Ball bearing fan with 2300 rpm – provides quiet
and long life expectancy and reliability.
7. Heat sink for memory.
8. Easy and fast installation.
Specication
Heat Sink Dimension : 160 x 91 x 34 mm
Fan Dimension : 80 x 80 x 15 mm
Base material : Copper
Fin material : Aluminum
Rated Voltage : 12 V
Rated Current : 0.19 Amp
Fan Speed : 2300 rpm
Noise : 25 dBA
Bearing Type : EB R Bearing
Fan Life Expectancy : 30,000 hr
Support :
nVIDIA 6600 PCI-E series
nVIDIA 7600 PCI-E serie
ATi RADEON X1650 series
ATi RADEON X700 series
ATi RADEON X1600 series
ATi RADEON X1300 series
ATi RADEON X800 series
Accessories
2) Wrench x 1 3) Heat Sink x 8
4) Washer x 4
5) Nut x 4 6) Screw x 4 7) Grease x 1
Bracket Instruction
GeForce 6600 LE
GeForce 6600
GeForce 6600 GT
GeForce 7300 GS
GeForce 7600 GS
GeForce 7600 GT
nVIDIA ATi
AGP
PCI-E
RADEON X800 XL
RADEON X800 GTO
RADEON X800
RADEON X800 XT
RADEON X800 Pro
RADEON X700 XT
RADEON X700 Pro
RADEON X700
RADEON X800 XL
RADEON X800
RADEON X800 XT
RADEON X800 Pro
AGP
PCI-E
nVIDIA ATi nVIDIA ATi nVIDIA ATi
TYPE A TYPE B
Installation Instruction ( ATi and nVIDIA )
Remove the original cooler on the VGA card and clean the grease.
( as Figure A )
According to the
number of the
memories on the VGA card, to remove
the sticker on the back of the heat
sinks and paste on the memories.
( as Figure B )
To replace the
cover, use the pincer
compress the collapsible end of the push
clips to slide out to remove the original
cover and put on the new one by aligning
the push clips with the lock holes on the
cooler and pushed completely through
the holes to lock it. ( as Figure D )
Lock the screws
on the bracket
with wrench. ( as Figure F )
To complete
the installation,
connect the power cord of the fan
to the output of the power supply.
( as Figure I )
Apply the
grease on
the VGA chip appropriately.
( as Figure C )
Tear off the
sticker on
the copper base. ( as Figure E )
Place the
cooler on the
table and align the holes for
the screws on the VGA card to
the screws on the cooler.
( as Figure G )
STEP 1
Remove heat sinks on the memories if any.
To avoid the da m a g e to th e
ch ip, pl ea s e l o ck the nu ts
diagonally.
Place the washers on
the screws and lock the
nuts on the screws with screwdriver to
fasten the cooler.
(as Figure H)
Figure B
Figure D
Figure F
Figure H
Figure A
Figure C
Figure E
Figure G
Figure I
STEP 2
STEP 4
STEP 6
STEP 8
STEP 3
STEP 5
STEP 7
STEP 9
Caution : Please be careful while removing the original heat sink on the VGA card. GIGABYTE
is not responsible to any loss caused during the removing process.
Please lock the screws on the
appropriate positions.
1) Cover ( red ) x 1
W h i l e i n s t a l l i n g t h e
power cor d of the fan,
please be careful not to
interfere to the blade.
Installation Guide
RADEON X1650 XT
RADEON X1650 Pro
RADEON X1600 XT
RADEON X1600 Pro
RADEON X1300 Pro
RADEON X1300