8S648FXP-RZ / 8S648FXP-RZ-C Intel® Pentium® 4 Processor Motherboard User's Manual Rev. 1001 12ME-S648FXPRZ-1001 Copyright © 2004 GIGABYTE TECHNOLOGY CO., LTD Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from without the expressed, written permission of GBT. Trademarks Third-party brands and names are the property of their respective owners.
Mother Board 8S648FXP-RZ Nov. 3, 2004 Motherboard 8S648FXP-RZ Nov.
Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside. 2. Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case. 3.
English Table of Contents Chapter 1 Introduction ................................................................................................... 5 Features Summary .................................................................................................................. 5 8S648FXP-RZ Series Motherboard Layout ............................................................................... 6 Block Diagram ............................................................................................
Features Summary Motherboard CPU Chipset Memory Slots IDE Connections FDD Connections Onboard SATA Peripherals Onboard LAN* Onboard Audio I/O Control Hardware Monitor Onboard SATA RAID BIOS Additional Features Form Factor y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y y 8S648FXP-RZ or 8S648FXP-RZ-C Socket 478 for Intel® Pentium® 4 (Northwood, Prescott) with HT Technology Intel ® Pentium ® 4 800/533/400MHz FSB 2nd cache depends on CPU Northbridge : SiS 648FX Southbr
21 cm CPU_FAN COMB LPT COMA Hyper Threading Support KB_MS ATX SOCKET478 F_AUDIO 29.5 cm LAN * DDR1 AGP 8X ICS1883 * DDR3 SiS 648FX DDR2 USB MIC_IN ATX_12V LINE_IN LINE_OUT 8S648FXP-RZ IDE2 IDE1 R_USB AGP BAT CODEC PCI1 CD_IN P4 Titan CLR_CMOS PCI2 SUR_CEN VRM10.0 SATA1 IT8705 PCI3 -C # English 8S648FXP-RZ Series Motherboard Layout SiS 964 SATA0 PCI4 BIOS PCI5 SPDIF_IO IR SYS _FAN FDD F_USB2 F_USB1 F_PANEL PWR_LED "*" Only for 8S648FXP-RZ.
English Block Diagram Pentium 4 Socket 478 CPU AGP 4X/8X CPUCLK+/- (100/133/200 MHz) System Bus 400/533/800 MHz AGPCLK (66MHz) 266/333/400 MHz DDR SiS 648FX ZCLK (66/133MHz) HCLK+/- (100/133MHz) 5 PCI RJ45 * 48 MHz ICS1883 * 66/133 MHz 33 MHz 14.318 MHz BIOS SiS 964 AC97 Link LPC BUS Floppy IT8705 AC97 CODEC LINE-IN LINE-OUT 24 MHz MIC PCICLK (33MHz) 2 SATA ATA33/66/ 8 USB 100/133 Ports Ports IDE Channels LPT Port PS/2 KB/Mouse 33 MHz 2 COM Ports "*" Only for 8S648FXP-RZ.
English Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Install I/O Peripherals Cables Step 4 Step 1 Step 2 Step 4 Step 4 Step 3 Step 1: Install the Central Processing Unit (CPU) Before installing the processor, adhere to the following warning: 1. Please make sure the CPU type is supported by the motherboard. 2.
Socket Actuation Lever English Step 1-1: CPU Installation Figure 1. Pull the rod to the 90-degree directly. Figure 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then move the socket lever to the locked position while holding pressure on the center of the CPU. Step 1-2: CPU Cooling Fan Installation Figure 1.
English Step 2: Install Memory Modules Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3. Memory modules have a foolproof insertion design.
AGP 4X/8X notch 3. Please carefully pull out the small white-drawable bar at the end of the AGP slot when you try to install/uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly down on the slot. Make sure your AGP card is locked by the small white-drawable bar.
English LAN port * The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps. Line In jack Devices like CD-ROM, walkman etc. can be connected to Line In jack. Line Out jack Connect the stereo speakers or earphone to this connector. MIC In jack Microphone can be connect to MIC In jack.
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start.
English 5) FDD (FDD Connector) The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position. 2 34 1 33 6) IDE1 / IDE2 (IDE1 / IDE2 Connector) An IDE device connects to the computer via an IDE connector.
PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. Pin No. 1 1 Definition MPD+ 2 3 MPDMPD- 9) F_PANEL (2 x 10 pins Connector) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below.
English 10) F_AUDIO (Front Audio Connector) If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer.
Please contact your nearest dealer for optional SUR_CEN cable. 6 5 2 1 Pin No. 1 Definition SUR OUTL 2 3 SUR OUTR GND 4 5 No Pin CENTER_OUT 6 BASS_OUT 13) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the CD_IN connector Pin No. 1 1 Definition CD-L 2 3 GND GND 4 CD-R 14) F_USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector.
English 15) IR Be careful with the polarity of the IR connector while you connect the IR. Please contact your nearest dealer for optional IR device. 1 Pin No. 1 Definition VCC 2 3 No Pin IR RX 4 5 GND IR TX 16) CLR_CMOS (Clear CMOS) You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer and pressing immediately will allow you to enter Setup. If you require more advanced BIOS settings, please go to "Advanced BIOS" setting menu.
English If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden. • Standard CMOS Features This setup page includes all the items in standard compatible BIOS. • Advanced BIOS Features This setup page includes all the items of Award special enhanced features. • Integrated Peripherals This setup page includes all onboard peripherals. • Power Management Setup This setup page includes all the items of Green function features.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features ` ` ` ` Date (mm:dd:yy) Time (hh:mm:ss) Thu, Oct 7 2004 22:31:24 IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave [None] [None] [None] [None] Drive A Drive B Floppy 3 Mode Suport [1.44M, 3.
English Drive A / Drive B The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity. 1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled). 720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity 1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity. 2.88M, 3.5" 3.5 inch double-sided drive; 2.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features ` Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Password Check CPU Hyper-Threading # Limit CPUID Max.
English Password Check System Setup The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. (Default value) CPU Hyper-Threading Enabled Disabled Enables CPU Hyper Threading Feature. Please note that this feature is only working for operating system with multi processors mode supported.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE AC97 Audio Onboard LAN device * USB Controller USB Legacy Support SiS Serial ATA Controller SiS Serial ATA Mode Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA KLJI: Move Enter: Select F5: Previous Values [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [En
English USB Controller Enabled Disabled Enable USB Controller. (Default value) Disable USB Controller. USB Legacy Support When USB keyboard or mouse is installed, please set at Enabled. Enabled Enable USB keyboard or mouse support. Disabled Disable USB keyboard or mouse support. (Default value) SiS Serial ATA Controller Enabled Disabled Enable onboard SiS serial ATA Controller. (Default value) Disable this function. SiS Serial ATA Mode IDE RAID Set onboard Serial ATA function as IDE.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR_BTTN System After AC Back IRQ [3-7, 9-15], NMI ModemRingOn PME Event Wake Up Power On by Keyboard Power On by Mouse Resume by Alarm x Month Alarm x Day (of Month) x Time (hh:mm:ss) Power LED in S1 state [S1(POS)] [Off] [Off] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [Disabled] NA Everyday 0:0:0 [Blinking] KLJI: Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: F
English Power On by Keyboard Any Key Password Disabled Set keyboard power on by any key. Enter from 1 to 8 characters to set the keyboard power on password. Disabled this function. (Default value) Power On by Mouse Enabled Disabled Power on system by move or click the mouse. Disable this function. (Default value) Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Date/time to power on system. Disabled Disable this function.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PnP/PCI Configurations PCI 4 IRQ Assignment PCI 1/5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Level` Device(s) using this INT: Display Cntrlr - Bus 1 Dev 0 Func 0 KLJI: Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Save Defaults ESC: Exit F1: General Help F7: Optimized Defaults PCI 4 IRQ Assignment Auto 3,4,5,7,9,10,11,12,14,15 Auto assign IRQ to PCI 4.
English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PC Health Status Vcore DDR2.5V +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed KLJI: Move Enter: Select F5: Previous Values OK OK OK OK 41°C 4440 RPM 0 RPM +/-/PU/PD: Value F10: Save F6: Fail-Save Defaults Current Voltage (V) Vcore / DDR2.5V / +3.3V / +12V Detect system's voltage status automatically. Current CPU Temperature Detect CPU temperature automatically.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software MB Intelligent Tweaker(M.I.T.) x x x x x x x x Configure DRAM Timing CAS Latency Setting DRAM RAS Active Time DRAM RAS Precharge Time DRAM RAS to CAS Delay CPU Clock Ratio Linear Frequency Control CPU Clock (MHz) DRAM Clock (MHz) AGP/PCI Clock Control AGP Clock (MHz) PCI Clock (MHz) DRAM Voltage Control KLJI: Move Enter: Select F5: Previous Values [Auto] 2.
English DRAM Clock (MHz) Please set DRAM Clock according to your requirement. If you use the DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If you use the DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333. If you use the DDR400 DRAM module, please set "DRAM Clock(MHz)" to Auto or 400. AGP/PCI Clock Control AUTO Manual Set AGP/PCI Clock Control to AUTO. (Default value) Set AGP/PCI Clock Control to Manual. AGP Clock (MHz) Please set AGP Clock according to your requirement.
English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ` ` ` ` ` ` ` Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password PnP/PCI Configurations Load Fail-Safe DefaultsSet (Y/N)? User NPassword PC Health Status Save & Exit Setup MB Intelligent Tweaker(M.I.T.
English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ` ` ` ` ` ` ` Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status MB Intelligent Tweaker(M.I.T.
English Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ` ` ` ` ` ` ` Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password PnP/PCI Configurations Save to CMOS and EXITSet (Y/N)? User Y Password PC Health Status Save & Exit Setup MB Intelligent Tweaker(M.I.T.
English 8S648FXP-RZ Series Motherboard - 36 -
English Revision Chapter History 3 Install Drivers Install Drivers Pictures below are shown in Windows XP Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CDtitle will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe.
English Driver installation finished! You have to reboot system! Item Description SIS AGP Driver AGP interface driver for SiS series chipset. USB Patch for WinXP This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP. SIS Mini IDE Driver SiS IDE controller driver. SiS PCI Lan Driver * For SiS series Lan driver. RealTek AC97 Audio Driver Audio driver for Realtek AC97 codec chipset. SiS 964 Serial ATA Driver Serial ATA driver for SiS964 South Bridge. SIS USB 2.
English Contact Us Taiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., LTD. Japan NIPPON GIGA-BYTE CORPORATION Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan. WEB address : http://www.gigabyte.co.jp Singapore TEL: +886 (2) 8912-4888 FAX: +886 (2) 8912-4003 GIGA-BYTE SINGAPORE PTE. LTD. Tech. Support : Tech. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : Non-Tech.
English China Australia NINGBO G.B.T. TECH. TRADING CO., LTD. Tech. Support : GIGABYTE TECHNOLOGY PTY. LTD. Address: 3/6 Garden Road, Clayton, VIC 3168 Australia http://cn.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : TEL: +61 3 85616288 FAX: +61 3 85616222 http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.gigabyte.com.cn Tech. Support : http://www.giga-byte.com.au/TechSupport/ServiceCenter.htm Shanghai TEL: +86-021-63410999 Non-Tech.
