7014 Series Industrial Gigabit Ethernet Switch User Manual & Installation Guide Rev.
7014TX, 7014FX2, and 7014FXE2 Industrial Gigabit Ethernet Switch Installation Guide........................................ 7 Safety Warnings ........................................................................................................................................................... 8 Installation .................................................................................................................................................................. 10 Connecting the Unit .............
Help – IGMP ........................................................................................................................................................................... 87 Help – Bridging ....................................................................................................................................................................... 88 Help – RSTP ..............................................................................................................................
Set Password ......................................................................................................................................................................... 110 Set IP Address of FTP server ................................................................................................................................................ 110 Set Name of the Remote File .......................................................................................................................
Set VLAN Ingress Filter ....................................................................................................................................................... 125 Get VLAN Ingress Filter ....................................................................................................................................................... 125 Get VLAN info ..........................................................................................................................................
Set RSTP Auto Edge ............................................................................................................................................................. 140 Get RSTP Auto Edge ............................................................................................................................................................ 140 Set RSTP Bridge Admin Status...........................................................................................................................
014TX, 7014FX2, and 7014FXE2 Industrial Gigabit Ethernet Switch Installation Guide The N-TRON 7014 Series Gigabit compatible Industrial Ethernet Switch offers outstanding performance and ease of use. It is ideally suited for connecting Ethernet enabled industrial and or security equipment and is a fully managed switch. PRODUCT FEATURES PRODUCT CONFIGURATIONS • Full IEEE 802.
Copyright, © N-Tron Corp., 2008 820 S. University Blvd., Suite 4E Mobile, AL 36609 USA All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-Tron Corp. is prohibited, except as allowed under copyright laws. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners.
ENVIRONMENTAL SAFETY WARNING: Disconnect the power and allow to cool 5 minutes before touching. ELECTRICAL SAFETY WARNING: Disconnect the power cable before removing any modules, or any enclosure panel. WARNING: Do not operate the unit with the any cover removed. WARNING: Do not work on equipment or cables during periods of lightning activity. WARNING: Do not perform any services on the unit unless qualified to do so. WARNING: Do not block the air vents.
PACKAGE CONTENTS Please make sure the 7014 Series Gigabit Ethernet Switch package contains the following items: 1. 2. 7014 Series Switch Product CD Contact your carrier if any items are damaged. Installation Read the following warning before beginning the installation: WARNING Never install or work on electrical equipment or cabling during periods of lightning activity. Never connect or disconnect power when hazardous gasses are present. Disconnect the power cable before removing any enclosure panel.
DIN RAIL MOUNTING Install the unit on a standard 35mm Din-Rail. Recess the 7014TX unit to allow at least 3” of horizontal clearance for fiber cable bend radius. Recess the 7014FX2 unit to allow at least 5” of horizontal clearance for fiber cable bend radius. To mount the unit to the 35mm din-rail, place top edge of the bracket on the back of the unit against the din-rail at an upward angle. Lower the bottom of the unit until it snaps into place.
FRONT PANEL From Top to Left: Gigabit Ports RJ45 Ports Fiber Ports 1000 Base SFP Copper or Fiber Transceivers (Optional) Auto Sensing 10/100 Base-TX Connections 100 Base-FX Connections (only on 7014FX2 model) Green LED lights when Power is supplied to the unit NOTE: The RJ45 data port has two LED’s located on each connector. The left LED indicates LINK status, and the right LED indicates ACTIVITY.
APPLYING POWER (Side View) • Unscrew & Remove the DC Voltage Input Plug from the Power Input Header • Install the DC Power Cables into the Plug (observing polarity). • For best results keep the power cable length to a maximum of one (1) meter. • Plug the Voltage Input Plug back into the Power Input Header. • Tightening torque for the terminal block power plug is 0.5 Nm/0.368 Pound Foot. • Verify the Power LED stays ON (GREEN). Note: Only 1 power supply must be connected to power for minimal operation.
Connecting the Unit For FX/FXE units, remove the dust cap from the fiber optic connectors and connect the fiber optic cables. The TX port on the FX/FXE models should be connected to the RX port of the far end station. The RX port on the FX/FXE versions should be connected to the TX port of the far end station. For 10/100 Base-TX ports, plug a Category 5E twisted pair cable into the RJ45 connector. Connect the other end to the far end station.
N-TRON SWITCH GROUNDING TECHNIQUES The grounding philosophy of any control system is an integral part of the design. N-Tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissions (i.e. CE) are obtained when the N-Tron switch chassis is connected to earth ground via a drain wire. Some N-Tron switches have metal din-rail brackets that can ground the switch if the din-rail is grounded.
CAT5 CABLE CRIMP SPECIFICATIONS Please reference the illustration below for your Cat5 cable specifications: Rev.
SERIAL INTERFACE The 7014 Series switches provide an EIA-232 interface accessed via a 9 pin female connector (labeled ‘COM’ on the unit). This is used to access the Command Line Interpreter (CLI). The pin-outs are shown below: Serial Cable Connect the serial COM port of your PC and the 7014 Series Switch using a standard straight through cable. You will require a cable with a 9-pin or 25-pin sub-D female connector for the PC end, and a 9-pin male sub-D connector for the 7014 Series end.
Overview of Advanced Features Mode of Operation Each port on the switch can be configured into different modes of operation as shown below: Copper Ports: 100Base Fiber Ports: 1000Base Copper/Fiber Ports: - Half Duplex - Full Duplex - Full Duplex - Full Duplex - Auto Negotiation Half Duplex In half duplex mode, the CSMA/CD media access method is the means by which two or more stations share a common transmission medium.
Priority Tagging (QoS) IEEE 802.1p priority tagging is supported for two classes of services along with bandwidth support per priority level. Transparent mode is supported through configuration wherein if the field is set, the tag bits are ignored. The User can configure up to 8 different priority levels per port. Also priority overriding (overriding the tagged field) can be enabled or disabled by the user.
SNMP Traps The 7014 Series switch supports up to 5 SNMP Trap Stations to which SNMP Traps will be sent. The switch supports three standard traps; Link Up, Link Down, and Cold Start. SNMP Traps will be sent to all the stations configured on the switch if a port Link goes up or down, and when the switch first powers up. IGMP Snooping IGMP Snooping is enabled by default, and the switch is Plug and Play for IGMP. IGMP snooping provides intelligent network support for multicast applications.
TROUBLESHOOTING 1. Make sure the (Power LED) is ON. 2. Make sure you are supplying sufficient current for the version chosen. Note: The Inrush current will exceed the steady state current by ~ 2X. 3. Verify that Link LED’s are ON for connected ports. 4. Verify cabling used between stations. 5. Verify that cabling is Category 5E or greater for 100Mbit Operation. SUPPORT Contact N-Tron Corp. at: TEL: 251-342-2164 FAX: 251-342-6353 E-MAIL: N-TRON_Support@n-tron.com WEB: www.n-tron.
Web Software Configuration Web Management Enter the switch’s IP address in any web browser and login to the web management feature of the 7014 Series. Default: User Name: admin Password: admin Rev.
Web Management - Home When the administrator first logs onto a 7014 Series switch the default home page will be displayed. On the left hand side of the screen there is a list of configurable settings that the 7014 Series switch will support. This section of the manual will go through each and every choice listed on the left hand side of the screen and explain how to configure those settings.
Web Management – Menu Structure To the left, there is a menu which is shown fully opened below. The pages opened by each of the individual selections are described in the rest of this section. The use of each of these pages is also described in this section. In most of the descriptions, only the right side of the page is shown. Rev.
Administration – System The System tab under the Administration category lists the following information about the switch: IP Address Subnet Mask Default Gateway MAC Address System Up Time Name Contact Information Location By selecting the modify button you will be able to change the switch’s IP Address, Subnet Mask, Default Gateway, Name, Contact information, and the Location of the switch through the web management features.
Administration – SNMP The SNMP tab under the administration category shows a list of IP Addresses that act as SNMP Traps. The Get, Set, and Trap Community Names are also shown here. By selecting the modify button you will be able to change any of the fields listed. This allows the user to set an IP address for an SNMP Trap or change the Community Names. Systems that are listed as an SNMP Trap will be sent basic networking changes made to the switch such as ports going down or being linked.
Administration – Gigabit Ports The ‘Gigabits Ports’ tab under the administration category allows users to change the configuration of the gigabit ports. The switch may not operate correctly if the slots are not configured properly. You must click “Update” if you wish to keep the changes. Notes: 1. In order to verify the settings have been configured and saved correctly, you may want to view the Logical View page in the found in the web browser interface.
Ports – Configuration The Configuration tab under the Ports category will show a detailed overview of all the active ports on the switch. The overview will display the following information: Port Number Port Name Admin Status Link Status Auto Negotiation State Port Speed Duplex Mode Flow Control State Back Pressure State Priority State Priority Level RSTP State PVID Rev.
Ports – Configuration, Continued… The User can click on the Port Number to configure each port individually. This will allow the user to change the port’s settings for the following fields: Admin Status Speed and Duplex Flow Control Back Pressure State of Priority Priority Level PVID Rev.
Ports – Security The Security tab under the Ports category will show a list of all the active ports and the security Lock State for each port. Rev.
Ports – Security (Continued) Administrators can change the Port Security by a per port basis. If the Port is enabled through this the port will be locked and will only allow known MAC addresses to communicate through the port. Unknown MAC addresses will be logged in the Intrusion Log. Rev.
Ports – Intrusion Log The Intrusion Log tab under the Ports category will show a list of intruders along with their MAC addresses. The log will show what Port the intruder attempted to access your network on and log the system time when it occurred. The log can be easily cleared. NOTE: This feature must first be enabled through the CLI before it will function in the web interface. Rev.
Ports – Mirroring A mirroring port is a dedicated port that is configured to receive the copies of Ethernet frames that are being transmitted out and also being received in from any other port that is being monitored. The Mirroring tab under the Ports category displays the status including the list of Source Ports and the Destination Port that the Sources are being mirrored to.
Ports – Trunking The Trunking tab under the Ports category displays a list of trunks configured on the switch and the following details regarding each trunk: Trunk Name Trunk Ports Trunk State By selecting the “Create” button, you can add a trunk group. NOTE: RSTP must be disabled in order to use the Trunking Feature. A maximum of 4 ports of the same speed can constitute a valid trunk. Only 1 Trunk per switch can be created. All trunk ports must be at the same speed and duplex mode.
Ports – Trunking, Continued… Once the Trunk Group is created you will see detailed information for that trunk group, but it should have a disabled state by default. In order to enable the Trunk Group you need to click on the State Button above. The following page should load asking for the Trunk ID and what the Trunk State is. NOTE: RSTP must be disabled in order to use the Trunking Feature. A maximum of 4 ports of the same speed can constitute a valid trunk. Only 1 Trunk per switch can be created.
Statistics – Port Statistics The Ports Statistics tab under the Statistics category displays a list of MIB Parameters. Each port has a separate counter for each parameter. This gives users the ability to see what kind of packets are going over which ports. At the bottom of each page for each port there are two buttons. Refresh will update the statistics for that port number and Clear will reset all the counters for that port number. Rev.
Statistics – Port Utilization The Ports Utilization tab under the Statistics category shows all the ports on the switch and will display a bar graph showing the percentage of bandwidth being used. These figures and bars are for a general feeling of what the bandwidth usage is. N-Tron recommends the use of N-View in order to get a precise bandwidth usage figure. Rev.
VLAN – Ingress Filter The Ingress Filter tab under the VLAN category shows all the Ingress Filter Rule enabled or disabled state for each port. Ingress Filtering can be Enabled or Disabled for each port. If enabled, received frames will be discarded if the frame's VID does not match any VLAN IDs associated with the port. This implements IEEE 802.1Q clause 8.6. Rev.
To change the Ingress Filter Rule simply click on the Modify button on the page above, select the port number from the pull-down menu that you wish to modify and then choose to either enable or disable the Ingress Filter Rule. NOTE: The Ingress Filter will automatically be turned on for respective ports when tagged VLANs are created, but may not automatically turn off if you change a tagged VLAN to a port based VLAN. Rev.
VLAN – Port Based The Port Based tab under the VLAN category shows all the VLANs that are configured on the switch and details about the VLANs such as port numbers and tagged VLAN settings. To add a VLAN simply click on the Add button on the page above and fill in the desired fields. The example below would set up a basic port based VLAN for ports P1-P6. Rev.
(See VLAN Configuration Examples section) Note: 1. When implementing overlapping VLANs, RSTP can only be enabled on one of the VLANs that is overlapping others. RSTP can not be implemented on a VLAN that contains other VLANs within that one. Changing anything on a VLAN will turn on RSTP on all VLANs as a precautionary measure. 2. All N-Ring ports must be on the same tagged VLAN. 3. VID=1 has to be Admit=ALL, and cannot be tagged only. Rev.
VLAN – Port Based, Continued… Now the page will display the new VLAN and moved ports P1-P6 from the default VLAN down to vlan2 that was just created. To delete or remove VLANs that are no longer wanted simply click on the Delete button on the main Port Based VLAN page. That button will load the page where the user can enter the VLAN ID that he or she wishes to delete. (See VLAN Configuration Examples section) Note: 1.
VLAN – Port Based, Continued… Once the VLAN is deleted it will no longer appear on the main page and all the ports are now back under the default VLAN. When a port based VLAN is created the PVID (Port VLAN ID) will change automatically to be members of the new VLAN they are a part of. If you delete this VLAN the PVIDs will not automatically return to the default VLAN. Users should keep this in mind when removing VLANs, and may need to manually change the PVIDs for any affected ports.
Bridging – Aging Time The Aging Time tab under the Bridging category will display the currently configured Aging Time. This page allows users to modify this variable to meet their needs. After selecting the Modify button the user will be presented with a page that allows the number to be entered into and updated. The default aging time is 20 seconds. Rev.
Bridging – Unicast Addresses The Unicast Addresses tab under the Bridging category will display a list of MAC addresses that are associated with each respective port number. This can be used to statically assign a MAC address access to a single port on the switch. Following the Add button on the page above, the administrator must enter a valid MAC address and associate it with a port number on the switch. Once the administrator hits the Update button the changes will take effect instantly.
Bridging – Unicast Addresses, Continued… Following the Delete button on the page above, an administrator can select a static MAC address from the list using a pull-down menu. After selecting the MAC address the administrator needs to press the Delete button on this page to remove the entry . Rev.
Bridging – Multicast Addresses The Multicast Addresses tab under the Bridging category will display a list of Multicast Group Addresses that are associated with respective port numbers. This may be used to statically assign a Multicast Group Address access to a group of ports on the switch. These are egress filters. Following the Add button on the page above, the administrator must enter a valid Multicast Group Address and associate it with a port number or list on the switch.
Bridging – Multicast Addresses, Continued… After adding a Multicast Group Address it will appear on the main list and will show the associated ports that go along with that address. Following the Delete button on the page above, the administrator will be presented with a list of Multicast Group Addresses that are configured on the switch. Using the pull-down menu the administrator should select the desired port to be removed. Then click on the Delete button at the bottom of the page.
RSTP – RSTP Configuration The RSTP Configuration tab under the RSTP category will display the RSTP information for the first VLAN. Using the pull-down menu at the top of the page an administrator can choose which VLAN to configure RSTP on. Once the VLAN is selected the administrator may configure the bridge by clicking on the Configuration button in the middle of the page. The configuration screen for the VLAN that was previously selected will look like the example below.
RSTP Configuration, Continued… Following the link for the view RSTP Port Configuration at VLAN# the administrator or user can see the current RSTP status of the ports on that VLAN. This will show information such as the Path Cost and the Port State. If the switch sees a redundant path it will put the port with the highest Path Cost into Blocking mode where it will discard packets coming in on that port.
RSTP – RSTP Configuration, Continued… If the administrator selects one of the ports on the previous screen he or she can change the Port’s Path Cost, Port’s Priority and the status of Admin Edge and Auto Edge. Rev.
IGMP – Configuration The Configuration tab under the IGMP category will display the IGMP basic configuration settings. By default IGMP is enabled. Following the Modify button on the previous page, the administrator will see a list of configurable fields for the IGMP configuration. Once these fields are filled in to meet the needs of the administrator’s network the changes may be saved by clicking the Update button at the bottom of the page. Rev.
IGMP – Configuration (continued) The IGMP Status pull-down allows the user to enable or disable IGMP completely. The Query Mode pull-down allows the user to set query mode for Automatic (the default), On (always), or Off (never): Rev.
IGMP – Configuration (continued) The Router Mode pull-down allows the user to choose router mode. ‘Auto’ allows for dynamically detected and manually set router ports. ‘Manual’ allows only for manually set router ports. ‘None’ allows no router ports. The user can add or delete manual router ports: Rev.
IGMP – Show Group and Show Router The Show Group tab under the IGMP category will display a list of IGMP groups based on the Group IP and the port number that it is associated with. The Show Router tab under the IGMP category will display a list of Auto-detected Router IPs and the port numbers that they are associated with. Rev.
IGMP – RFilter The ‘rfilter’ (Router Multicast Data Filter) function allows you to choose whether or not DATA frames with KNOWN group multicast addresses are sent to the ‘router’ ports (links to other switches). Control packets (Join, Leave) will be sent to the router(s) regardless of this setting. “KNOWN” is known from dynamic IGMP Snooping operations.
IGMP – Rfilter (Continued) Modifying rfilter port settings: Rev.
N-View – Configuration The Configuration tab under the N-View category will display two basic variables for N-View, the status and the interval between packets. Following the Modify button on the above example, the administrator can modify the variable to change the frequency with which N-View reports information. Increasing the interval will slow the update rate. Decreasing the interval will allow N-View to report more frequently. Additionally, you may Disable or Enable N-View altogether. Rev.
N-View – Ports The Ports tab under the N-View category will display a list of all the configured ports on the 7014 unit along with the ports transmitting multicast packets and MIB stats respectively. Rev.
N-View – Ports, Continued… Following the Modify button on the previous example, the administrator can modify these two variables to enable or disable multicast out of the port and if MIB stats are sent out for those ports. Rev.
N-Ring - Configuration The Configuration tab under the N-Ring category will display the N-Ring basic configuration settings. By default N-Ring is in AutoMember mode and the N-Ring agingtime is 20 seconds. Following the Modify button on the previous page, the administrator will see a list of configurable fields for the N-Ring configuration, as below. The N-Ring Agingtime has a default of 20 seconds and is separate from the Bridging Aging Time.
NOTES: 1. N-Ring Manager cannot have RSTP or Trunking enabled. 2. RSTP & N-Ring are different modes and cannot share links or segments along those lines. See the examples in the RSTP configuration section. 3. Do not use Trunking on a switch that is directly in an active N-Ring. 4. Any one 7014 can only participate in one N-Ring. 5. N-Ring copper ports must be run at 100Mb full duplex, including the default ‘autonegotiate’ as long as all switches in the ring support 100Mb full duplex.
Rev.
N-Ring Configuration (continued) If N-Ring Mode is “Manager”, then a pull-down allows selection of displaying N-Ring Summary Status on all web pages or on N-Ring pages only: Rev.
N-Ring Configuration (continued) If N-Ring Mode is “Manager”, then VLAN ID can be set to a unique vlan id (1 ~ 4094). Default is 3333. If N-Ring Mode is “Manager”, then a pull-down allows selection as to whether the N-Ring ports are members of the VLANs Tagged or Untagged ports. Default is Tagged. Once these fields are filled in to meet the needs of the administrator’s network the changes may be saved by clicking the Update button at the bottom of the page. NOTES: 1.
N-Ring – Status The Status tab under the N-Ring category will display the N-Ring status. Below is an example of N-Ring Status from a switch in defaults (N-Ring Auto Member) that is not an NRing Manager and has not become an “Active” N-Ring Member: Below is an example of N-Ring Status from an “Active” N-Ring Member: Rev.
Below is an example of N-Ring Status from an N-Ring Manager with a healthy N-Ring: N-Ring OK N-Ring Status View Switch is an N-Ring Manager, using N-Ring Aging Time = 20 Seconds Refresh every 6 secs. Update Pause Print... 12 Active Members Detected In Current N-Ring (12 reporting) Switch No MAC Address Rev. 051208 IP Address Subnet Mask Name Ports RM 00:07:af:ff:e4:a0 192.168.1.227 255.255.255.0 N-TRON Switch GB2 GB1 1 00:07:af:ff:ef:60 192.168.1.224 255.255.255.
Below is an example of N-Ring Status from an N-Ring Manager with a faulted N-Ring. The red fields on the N-Ring Map show problems. Ports that are red indicate that the port is not linked. MAC addresses that are red indicate that there is no communication to that switch. The red “Ring Broken” line shows where the N-Ring is broken. N-Ring Fault N-Ring Status View Switch is an N-Ring Manager, using N-Ring Aging Time = 20 Seconds Refresh every 6 secs. Update Pause Print...
In rare cases an N-Ring can have a “Partial Fault”. An example of this is to have a break in just one fiber in a duplex channel fiber pair.
Event Log – Log Statistics The Log Statistics tab under the EventLog category will show a list of how many times a type of event took place. On the bottom of the page it also lists the maximum log size which can be modified. There are 5 types of events that the 7014 will categorize messages in. If the log level is set to 1, the 7014 will log all 5 types of events. If the log level is set to 5 it will only record the Critical types (the 5th level).
Event Log – Show Events The Show Events tab under the Event Log category will show a list of events that have occurred in the order in which they occurred. There is a time stamp for each event and they are categorized by the severity of the event. Rev.
Firmware/Config - TFTP The TFTP tab under the Firmware/Config category gives the administrator the ability to upload or download a config file for a 7014 Series switch. This gives administrators the ability to backup their configurations to a server offsite in case they need to reload their custom configurations at a later time.
Firmware/Config - FTP The FTP tab under the Firmware/Config category gives the administrator the ability to upload or download a config file for a 7014 Series switch. This gives administrators the ability to backup their configurations to a server offsite in case they need to reload their custom configurations at a later time.
Support – Web Site and E-mail If at any point in time you get confused or would like additional support directly from N-Tron, you may visit N-Tron’s web site, or e-mail N-Tron directory with the links provided for more information. Rev.
BPCL – Broadcast Packet Count Limit Configuration The BPCL link will display all the ports that are installed in the 7014 Series unit and will list the BPCL Percentage for each port. BPCL defaults to 3%. A modify button is provided to change these fields. These are egress filters. Rev.
BPCL – Broadcast Packet Count Limit Configuration (Continued) Following the Modify button on the previous example, the administrator can modify the BPCL Percentage for each port. Rev.
User Mgmt – Adding Users The User Management link will display a list of all the users who have access to the management features of the switch and their access permissions. Following the Add button on the previous example, the administrator can add another user and assign the user a username, a password, and the user’s permissions (user/administrator). A page should display after the administrator clicks the Add button stating that the user was successfully added.
User Mgmt – Removing Users In order to remove a user, simply click on the Remove button at the bottom of the page. Following the Remove button on the last page, the administrator can remove a user by entering in the user’s name and clicking the Remove button. A page should follow stating that the user was successfully removed from the list. Rev.
LogicalView The 7014 Web Management offers a logical view of the switch. Here a user or administrator can see a graphical depiction of the 7014 switch. Ports that are linked will turn green, while ports that are not linked will show up as black. The example below shows ports 1,3,5,6,7,8,9,10, and 12 linked. The other ports are currently in the down state (not being used). Rev.
Configuration – Save or Reset The Configuration section of the web management gives an administrator the ability to save a running configuration into the NVRAM. This step is needed in order for the switch to remember any changes after a power cycle. The Reset Configuration button will reload N-Tron’s factory default configuration settings. Doing so will re-configure the 7000 Series switch to factory defaults.
Help – Overview When the Help link is clicked on, you will see the Overview page that will have some basic definitions and more specific choices at the top of the screen. Although this page is not as detailed as the manual is, it gives you a basic feel for different features the 7014 offers. Rev.
Help – Administration Selecting the Administration link on the help page, the administrator or user can see some information regarding the configuration options in the Administration category on the left side of the web management. Rev.
Help – Ports Following the Ports link on the help page, the administrator or user can see some information regarding the configuration options in the Ports category on the left side of the web management. Rev.
Help – Statistics Following the Statistics link on the help page, the administrator or user can see some information regarding the configuration options in the Statistics category on the left side of the web management. Rev.
Help – VLAN Using the VLAN link on the help page, the administrator or user can see some information regarding the configuration options in the VLAN category on the left side of the web management. Rev.
Help – BPCL Using the BPCL the link on the help page, the administrator or user can see some information regarding the configuration options in the BPCL category on the left side of the web management. Rev.
Help – IGMP Following the IGMP link on the help page, the administrator or user can see some information regarding the configuration options in the IGMP category on the left side of the web management. Rev.
Help – Bridging Using the Bridging link on the help page, the administrator or user can see some information regarding the configuration options in the Bridging category on the left side of the web management. Rev.
Help – RSTP Using the RSTP link on the help page, the administrator or user can see some information regarding the configuration options in the RSTP category on the left side of the web management. Rev.
Help – Event Log Using the Event Log link on the help page, the administrator or user can see some information regarding the configuration options in the Event Log category on the left side of the web management. Rev.
Help – Firmware/Config Using the Firmware/Config link on the help page, the administrator or user can see some information regarding the configuration options in the Firmware/Config category on the left side of the web management. Rev.
Help – Logical View Using the Logical View link on the help page, the administrator or user can see some information regarding the configuration options in the Logical View category on the left side of the web management. Rev.
Help – User Mgmt Using the User Mgmt link on the help page, the administrator or user can see some information regarding the configuration options in the User Mgmt category on the left side of the web management. Rev.
Help – N-View Using the N-View link on the help page, the administrator or user can see some information regarding the configuration options in the N-View category on the left side of the web management. Rev.
Help – N-Ring Using the N-Ring link on the help page, the administrator or user can see some information regarding the configuration options in the N-Ring category on the left side of the web management. Rev.
Help – Others Following the “Others” link on the help page, the administrator or user can see some information regarding other links or categories on the left hand side of the web manager, as above. Rev.
CLI Commands Clear Command Name Description Syntax Parameters Examples clear Clears the screen. The cleared screen shows only the command-line prompt and the cursor. clear None N-TRON/Admin#[1]> clear The entire screen will be cleared… … … … … N-TRON/Admin#[2]> NOTES “?” (HELP) Command Name Description “?” Without , this command will list all the available commands. This is the same as the default behavior of the help command.
Top Command Name Description Syntax Parameters Examples top Changes the context to the topmost (global) level. If already at the topmost context, the command is simply ignored top None N-TRON/Admin#[1]system> show N-TRON/Admin#[2]system/show> top N-TRON/Admin#[3]> top N-TRON/Admin#[4]> NOTES Up Command Name Description Syntax Parameters Examples up Changes the context to the next higher level.
History Command Name Description Syntax Parameters Examples history Lists all the commands in the history list for the current session, identifying each command with a reference number. history –reverse reverse the order of display to be the most recent entry first. –maxsize set the maximum no. of entries that will be maintained in the list to the given value. –clear remove all entries in the command history list. N-TRON/Admin#[1]> history The above command displays previously entered commands.
“!” Command Name Description Syntax Parameters Examples ! Repeats the command in the history list identified by . !! – repeats the last command executed. ! – repeats the command in the history list associated with reference number . ! – repeats the most recent command that begins with the string . Any non-whitespace characters that follow are appended to the referenced command prior to its execution.
Description Syntax Parameters This command copies the command identified by reference number from the history list into the next command line allowing the user to edit the command for corrections or changes. $ n The reference number of the command in the history list that has to be edited. Examples N-TRON/Admin#[1]> whoaim As shown above the command whoaim was entered instead of whoami. To edit the already entered command do as follows.
System Configuration Commands Set Mode IP config Command Name Description Syntax Parameters Example NOTES system set modeipconfig To set the IP address mode of the system system set modeipconfig manual Uses a static IP address scheme (default mode) dhcp Pulls an IP address from a DHCP server on the LAN bootp Pulls an IP address from a Bootp server on boot up N-TRON/Admin#[1]> system set modeipconfig dhcp Bootp is an older version of DHCP, DHCP is recommended for a dynamic address sche
Get System Name Command Name Description Syntax Parameters Example system get sysname To display the name of the system system get sysname None N-TRON/Admin#[1]> system get sysname System Name : N-TRON Switch Notes Get Gateway Address of the System Command Name system get gateway Description To display the gateway address of the system Syntax system get gateway Parameters None N-TRON/Admin#[4]> system get gateway Example System Gateway Address : 192.168.1.
Set System Contact Command Name Description Syntax Parameters system set syscontact To set the contact details for the system system set syscontact Contact-for-the-system The details of the person to be contacted for this system in case of any queries or problems Example N-TRON/Admin#[1]> system set syscontact admin@N-Tron.
Set IP Address of the SNMP Manager Command Name system set snmpmgmtip Description To set the IP address of the SNMP manager Syntax Usage: system set snmpmgmtip Parameters Station Number 1->5. IP Address The IP address of the SNMP manager in dotted decimal notation N-TRON/Admin#[1]> system set snmpmgmtip 10.1.5.100 Example N-TRON/Admin#[2]> system set snmpmgmtip 10.1.6.150 NOTES The IP address should be a valid IP address (excluding Class D & Class E type).
Show all configuration parameters Command Name system show config Description Displays the software version, the mac address, and status of gigabit ports.
User Management Commands Show System Users Command Name Description Syntax Parameters Example system show users Shows a list of users and their permissions on the system system show users None N-TRON/Admin#[1]> system show users Serial -----1 2 Username -------admin ntron Access Permissions -----------------admin user NOTES Add a System User Command Name Description Syntax Parameters system add user To add a user to the system system add user [access permission] Username A string of at least
Modify a User’s Password Command Name Description Syntax Parameters system modify userpassword To change a user’s password system modify userpassword Username The user’s username that is to be modified Password The new password for the user Example N-TRON/Admin#[1]system/modify> userpassword ntron Enter New Password :***** Confirm New Password :***** Password has been modified successfully Notes A user with user permissions can operate this command, but will be prompted for the old password
TFTP Commands Set the TFTP configuration parameter Command Name tftp set Description To set the TFTP configuration parameters TFTP Server IP Address and Remote File name. Syntax tftp set serverparam Parameters ip-address TFTP Server IP Address in dotted decimal notation for establishing the connection to transfer the file. remote-file-name Name of the remote file (including complete path) to be retrieved from the TFTP Server. Examples eg.
FTP Commands Set Username Command Name Description Syntax Parameters Example ftp set username To set the user name which will be used to log into the FTP server ftp set username Username The user name for logging on to the FTP server eg.1 N-TRON/Admin#[1]> ftp set username ntron eg.2 N-TRON/Admin#[1]> ftp set username admin Notes Set Password Command Name Description Syntax Parameters The user name should be a valid one; else logging into FTP server will fail.
Display FTP related configuration parameters Command Name ftp show Description To display the present value of all the FTP related configuration parameters Syntax ftp show Parameters None N-TRON/Admin#[1]> ftp show Example Notes Perform the configuration file transfer action Command Name ftp config Description To perform the desired File Transfer action (either get or put).
Port Manager Commands Get the link state of a given port Command Name port get linkstate Description This command is used to get the present link state of a given port. Whenever there is an active connection, link state (operational state) is up; else link state is down. Syntax port get linkstate Parameters port-no Port number. (1 ~ 14).
Show port statistics Command Name Description Syntax Parameters Examples NOTES port show stats This command is used to get the port statistics of a given port for all available counters. port show stats port-no Port number. (1 ~ 14).
Set Port Speed Command Name Description Syntax Parameters Examples port set speed Sets the port speed of a given port. port set speed port-no Port number. (1 ~ 12) speed Speed of the port. Speed must either 10, 100, 1000 megabits per sec. N-TRON/Admin#[1]> port set speed 5 10 N-TRON/Admin#[2]> port set speed 9 100 NOTES Get the port duplex mode Command Name Description Syntax Parameters If the auto negotiation mode is enabled, port speed cannot be set.
Get Lock State Command Name Description Syntax Parameters port get lockstate Gets the lock state for a given port. port get lockstate port-no port number (1 ~ 14). Examples N-TRON/Admin#[1]> port get lockstate 6 LockState : [enable] N-TRON/Admin#[2]> port get lockstate 14 LockState : [disable] NOTES Check whether port-no is in the valid range. (1 ~ 14) Get Auto-negotiation State Command Name Description Syntax Parameters port get autonego Gets the auto negotiation mode for a given port.
Set Flow Control Command Name Description Syntax Parameters Examples NOTES Set Name Command Name Description Syntax Parameters Examples NOTES Set PVID Command Name Description Syntax Parameters Examples NOTES Set Backpressure Command Name Description Syntax Parameters Examples NOTES Set Intruderstate Command Name Description Syntax Parameters Examples NOTES Rev. 051208 port set flowcontrol Enable or Disable flow control (typically refers to 100Base).
Set Priority Level Command Name Description Syntax Parameters Examples NOTES Show Configuration Command Name Description Syntax Parameters Examples NOTES Show Intruders Command Name Description Syntax Parameters Examples NOTES Show Link Utilization Command Name Description Syntax Parameters Examples NOTES Get Flow Control Command Name Description Syntax Parameters Examples NOTES Get Name Command Name Description Syntax Parameters Examples NOTES Rev.
Get State Of Priority Command Name Description Syntax Parameters port get stateofpriority Displays the priority state of a given port number. port get stateofpriority port-no port number (1 ~ 14) Examples N-TRON/Admin#[1]> port get stateofpriority 6 Priority State of Port[6] is : [disabled] NOTES Check whether port-no is in the valid range.
Get PVID Command Name Description Syntax Parameters port get pvid Displays a given port’s VLAN-ID. port get pvid port-no port number (1 ~ 14) Examples N-TRON/Admin#[1]> port get pvid 6 PVID of port 6 is 4. NOTES Check whether port-no is in the valid range. (1 ~ 14) Clear Counters Command Name Description Syntax Parameters port clear counters Clears all the numbers in the counters for a given port. These are counters for RX bytes and TX bytes and so on.
Trunk related commands Enable or disableTrunking Command Name Description Syntax Parameters Examples NOTES Modify Trunk Command Name Description Syntax Parameters Examples NOTES Create Trunk Command Name Description Syntax Parameters Examples NOTES Delete Trunk Command Name Description Syntax Parameters Examples trunk set To enable or disable the trunk that is already created.
Show Trunk Information Command Name Description Syntax Parameters Examples trunk show To show all the trunks information. trunk show None N-TRON/Admin#[1]> trunk show -----------------------------------------------| TRUNK NAME | TRUNK PORTS | TRUNK STATE | -----------------------------------------------| trunk1 | 3-5 | DISABLE | ------------------------------------------------ NOTES Rev.
Mirroring related commands Set Mirror config Command Name Description Syntax Parameters Examples NOTES mirror set config To the mirroring feature of the switch, for specified ports. mirror set config dest-port Destination port is the snooper port onto which the selected source ports traffic is to be mirrored. The gigabit ports cannot be destination ports. src-ports List of ports to be monitored.
VLAN Related Commands Add VLAN Entry Command Name Description Syntax Parameters vlan add To create a Port based Virtual LAN vlan add ] or [-tagged ]> [-name ] [-admit ] [-mirror ] vlan-id Unique vlan id (2 ~ 4094). mgmt port Either 1 or 0. ‘1’ sets this vlan as a management vlan. vlan name Unique vlan name, which can be used to identify the group.
Display Information of a particular VLAN Command Name vlan get info Description Displays the details of a particular VLAN. Syntax vlan get info Parameters vlan-id Vlan id of the existing vlan whose individual configuration is required. N-TRON/Admin#[1]> vlan get info 2 Examples vlan ID : vlan Name : port list : tagged port mask: management port : 2 “vlan 2” 1-4,11 10-15 NO NOTES Modify an existing VLAN Command Name Description Syntax Parameters Examples vlan modify Modifies an existing VLAN.
Delete VLAN Command Name Description Syntax Parameters Examples NOTES vlan delete Removes an existing VLAN from the list of configured VLANs. vlan delete vlan-id Vlan id of the existing vlan which has to be deleted N-TRON/Admin#[1]> vlan delete 2 Please ensure that a port based vlan with the given vlan id exists. Changing anything on a VLAN will turn on RSTP on all VLANs as a precautionary measure.
Get VLAN info Command Name Description Syntax Parameters Examples NOTES Rev. 051208 vlan get info Displays the current state of the configured vlans.
Eventlog Related Commands Get Eventlog count Command Name Description Syntax Parameters Examples eventlog get count To display the logged events count eventlog get count None N-TRON/Admin#[1]> eventlog get count No.
Show Eventlog events Command Name Description Syntax Parameters Examples NOTES Rev.
Bridging Related Commands Add Multicast MAC Address Command Name Description Syntax Parameters Examples NOTES Delete Multicast MAC Address Command Name Description Syntax Parameters Examples NOTES Add a Unicast MAC Address Command Name Description Syntax bridge add multicastmac Adds a multicast mac address which is associated with a vlan.
Display List of Configured Static MAC Addresses Command Name bridge show staticmac Description To view the list of configure static mac addresses Syntax bridge show staticmac Parameters which set of static mac addresses to show N-TRON/Admin#[1]> bridge show staticmac all Examples N-TRON/Admin#[2]> bridge show staticmac multicast N-TRON/Admin#[3]> bridge show staticmac unicast NOTES Set Aging Time Command Name Description Syntax Parameters Examples NOTES Disp
Display Mac count Command Name Description Syntax Parameters Examples NOTES Rev. 051208 bridge show maccount Displays the total count of the static mac addresses.
IGMP Related Commands Enable IGMP Command Name Description Syntax Parameters Examples igmp set enable The igmp status is made to enable .
Show IGMP router Command Name Description Syntax Parameters Examples NOTES Set IGMP query mode Command Name Description Syntax Parameters Examples NOTES Set IGMP router port Command Name Description Syntax Parameters Examples NOTES Set IGMP router mode Command Name Description Syntax Parameters Examples NOTES Show IGMP rfilter mode Command Name Description Syntax Parameters Examples igmp show router The igmp show router command is used to display the auto-detected routers at present.
---------------------------5 DISABLE N-TRON/Admin#[6]igmp/show> igmp show rfilter 5-7 Port No. IGMP RFilter ---------------------------5 DISABLE 6 DISABLE 7 DISABLE N-TRON/Admin#[7]igmp/show> NOTES Set IGMP rfilter mode Command Name Description Syntax Parameters Examples Default: enable igmp set rfilter The igmp set rfilter command is used to enable or disable rfilter based on a port-range.
N-Ring Related Commands N-Ring get agingtime Command Name Description Syntax Parameters Example n-ring get agingtime To display the N-Ring Agingtime of the device n-ring get agingtime None N-TRON/Admin#[1]> n-ring get agingtime N-Ring Aging Time NOTES N-Ring set agingtime Command Name Description Syntax Parameters Examples NOTES N-Ring get webfault Command Name Description Syntax Parameters Example : 20 Default: 20 seconds and is separate from the Bridging Aging Time.
N-Ring get interval Command Name Description Syntax Parameters Example n-ring get interval To display the Self-Health Packet interval and missed threshold. n-ring get interval None N-TRON/Admin#[1]> n-ring get interval Self Health Packet interval is 1 Maximum Missed Packets is 2 NOTES Default: interval=1, missed=2 N-Ring set interval Command Name Description Syntax Parameters Examples n-ring set interval Sets the Self-Health Packet interval and missed threshold.
N-Ring VLAN ID is set to: 3333 N-Ring Tagging is set to: Tagged ................ ................ Device is Going for Reboot.... NOTES N-Ring show status Command Name Description Syntax Parameters Examples NOTE: N-Ring Manager cannot have RSTP enabled. Do not use Trunking on a switch that is directly in an active N-Ring. n-ring show status Shows the current N-Ring status of the switch. If Manager, shows ring members. Shows if Automember or active member. If active (manager or member) shows N-Ring ports.
N-Ring show switch Command Name Description Syntax Parameters Examples n-ring show switch From the N-Ring Manager, shows info about a switch on the N-Ring. n-ring show switch N-TRON/Admin#[12]n-ring/show> switch 00:07:af:ff:f6:40 Information for 00:07:af:ff:f6:40 Name Location Product Name Product Version IP Address Subnet Mask N-Ring Port 1 N-Ring Port 2 : : : : : : : : N-TRON Switch Mobile, AL 36609 N-TRON 7000 Series 4.1.1 192.168.1.233 255.255.255.
Configuration Related Commands Save Configuration Command Name Description Syntax Parameters Examples NOTES Load Default Configuration Command Name Description Syntax Parameters Examples config save The configuration will be saved to the flash. config save None N-TRON/Admin#[1]> config save config erase This command is useful to erase the configuration data config erase None N-TRON/Admin#[1]> config erase Load Factory Default Setting.
Rapid Spanning Tree Protocol Related Commands Set RSTP Admin Edge Command Name Description Syntax Parameters Examples rstp set adminedge Sets the Adminedge value of a port in a Vlan. rstp set adminedge vlan id Vlan Id containing the port for which the adminedge is to be set. port no Port number in the Vlan to be set. status Status of the adminedge of the port to be set.
Set RSTP Bridge Admin Status Command Name Description Syntax Parameters Examples rstp set bridgeadminstatus Sets the Bridge Admin Status of the given Vlan-ID. rstp set bridgeadminstatus vlan id Vlan Id for which the priority to be set. bridge adminstatus Status of the Bridge to be set.
Set RSTP Bridge Hello Time Command Name Description Syntax Parameters rstp set bridgehellotime To set the HelloTime for a given Vlan-Id. With STP, Hello Time is the time intervals that the root bridge sends out new BPDUs to the rest of the network. Other STP capable switches will forward these BPDUs along. With RSTP every RSTP capable switch will generate new BPDUs and send them out on every Hello Time Interval.
Set RSTP Bridge Priority Command Name Description Syntax Parameters rstp set bridgepriority Sets the Bridge Priority. The root bridge on the network will be the one with the lowest bridge priority, or the lowest MAC address if the priorities are the same (as per IEEE 802.1D specification). rstp set bridgepriority vlan-id Vlan Id for which the priority to be set. bridge priority Priority of the Bridge to be set. The value should range between 0 and 65535. (as per IEEE 802.
Set RSTP Port Priority Command Name Description Syntax Parameters rstp set portpriority To set the priority of the port for a given port in the given vlan-id. STP and RSTP use the port priority to determine which port to place into forwarding mode when there are 2 or more ports to choose from. rstp set portpriority vlan-id Vlan Id to which the port belongs. port no The portnumber for which the port priority is to be set. port priority The Port priority value to be set.
Broadcast Packet Count Limit Commands Get the Broadcast Packet Count Limit for one port Command Name broadcast get percentage Description Displays the broadcast packet percentage for a particular port. Syntax broadcast get percentage Parameters port-number The port number must range between 1 and the maximum port number in the switch.
VLAN Configuration Examples Example 1 – Basic understanding of port based VLANs VLAN Configuration View Ports Configuration View VLAN Status : Enable Port Port PVID No Name VLAN ID VLAN Name Untagged Port(s) Tagged Port(s) Mgmt Port Admit Mirror Port 1 Default VLAN P3-P12 -YES All 0 2 VLAN -2 P1-P2 -- YES All 0 Receiving Port # Tagged VID in packet Destination Address Transmitting Port #s Notes Port P1 Port P1 Port P1 Port P3 Port P3 Port P3 Untagged Untagged VID 4 Untagged Untagged VID 4
Example 3 – Basic understanding of tagged VLANs (Admit – All) VLAN Configuration View Ports Configuration View VLAN Status : Enable Port Port PVID No Name VLAN ID VLAN Name Untagged Port(s) Tagged Port(s) Mgmt Port Admit Mirror Port 1 Default VLAN -- P3-P12 YES All 0 2 VLAN -2 -- P1-P2 YES All 0 1 P1 ** 2 P2 ** 3 P3 ** ...
Example 5 – Basic understanding of Overlapping VLANs VLAN Configuration View Ports Configuration View VLAN Status : Enable VLAN ID VLAN Name Untagged Port(s) Tagged Port(s) Mgmt Port Admit Mirror Port Default VLAN -- -- YES All 0 2 VLAN -2 P1-P12 -- YES All 0 3 VLAN -3 P2-P12 -- YES All 0 1 P1 4 0 2 P2 2 3 P3 3 4 P4 2 5 P5 3 4 Rev. 051208 Port Port Na PVID No me 1 VLAN -4 P1-P2 -- YES All ...
Example 6 – Basic understanding of VLANs with Multicast Filtering VLAN Configuration View Ports Configuration View VLAN Status : Enable VLAN ID VLAN Name Untagged Port(s) Tagged Port(s) Mgmt Port Admit Mirror Port 1 Default VLAN -- -- YES All 0 2 VLAN -2 P1-P12 -- YES All 0 3 VLAN -3 P2-P12 -- YES All 0 4 VLAN -4 P1-P2 -- YES All 0 Display Static Multicast Group Address(es) Multicast Address Port List 01:00:00:00:00:01 Port Port PVID No Name 1 P1 4 2 P2 2 3 P3 3 ...
KEY SPECIFICATION Switch Properties Number of MAC Addresses: Aging Time: Latency Type: Switching Method: 4,096 Programmable 2.9 µ s Store & Forward Physical Height: Width: Depth: Weight (max): Din-Rail mount: 2.50” / 6.35 cm 7.40” / 18.8 cm 4.10” / 10.4 cm 2.10 LBS / 0.95 kg 35mm Electrical Redundant Input Voltage: Input Current (max): Inrush @ 24VDC: Input Ripple: N-TRON Power Supply: 10-30 VDC 3.0 A 12.6A/0.
100 Mb Fiber Transceiver Characteristics Fiber Length TX Power Min/Max 2km* 15km** 40km** 80km** -19dBm/-14dBm -15dBm/-7dBm -5dBm/0dBm -5dBm/0dBm RX Sensitivity Max Wavelength Min/Max -32dBm -29dBm -34dBm -34dBm 1310nm 1310dm 1310dm 1550nm * Multimode Fiber Optic Cable ** Singlemode Fiber Optic Cable Gigabit Fiber Transceiver (SFP) Characteristics Fiber Length 550m* with 50/125 µm 10km** 40km** 70km** TX Power Min/Max -9.5dBm/-4dBm -9.5dBm/-3.
N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller.
