3D Galaxy II GH-WIU02 English User’s Manual
English 3D Galaxy II Liquid Cooling System Caution 1. Before pouring liquid coolant into the tank to test the liquid cooling system, please reconfirm all the tubes have been fastened and the tube clips are in the right position. 2. While the water in the tank is lower than the low water-level, the red light on the bottom of PCB will blink. (Please purchase GIGABYTE™ liquid coolant to fill it.) 3.
English Table content 1 Accessories List 4 2 Specification Instruction 6 3 Feature Instruction 6 4 Liquid Cooling System Installation 7 4-1 Installation Preparation ® ® 7 4-2 Intel Pentium 4 LAG775 Back Plate Installation 7 4-3 PCI Rear Fan Speed Controller Installation 8 4-4 Tube Installation 8 4-5 4-way Splitter Valve to the Tube on Waterblock Installation 9 4-6 Radiator to 4-way Splitter Valve Installation 10 4-7 Radiator to the Inlet of Water Tank 11 4-8 4-way Splitter Va
English 1.
English X8 pcs (17)Pump Power Cord X2 pcs (21)Bend Proof Spring (18)Fan 1 to 2 Power Cord (19)Fan Speed Control Power Cord (20)Heat Sink for Memory (23)Grease (24)Gigabyte Liquid Coolant X4 pcs (22)Nylon Tie X2 (25)Velcro (26)Quick Installtion Guide No.
English 2.
English 5.Delicate sparkly blue LED light design tank; easy refilling coolant. 6.Well-executed liquid cooling radiator fits most existed PC chassis. 7.Multipurpose nanometer GIGABYTE™ coolant. 8.1/2inch UV soft tube; unique design to reduce bending needs. 9.Fully support cooling solution for the surrounding component of CPU (Mosfet). 10.GIGABYTE™ excusive 4-way splitter valve design for faster replacement and add new cooling equipment. 11.PCI Rear Fan Speed Controller 12.Free heat sink for memory 13.
English 4-3 PCI Rear Fan Speed Controller Installation (as Figure a/b) 4-3-1 Place PCI rear fan speed controller to the back of the chassis (place on the lower PCI is recommended as Figure c.) Figure a Figure b Figure c 4-4 Tube Installation After measuring the distance between each parts of the cooling system, cut the tubes into five suitable sizes as it shows below. To get the right length for each tube, strongly recommend to fit all the components in the right position.
English Tube1 Tube3 Tube4 Tube2 Tube5 While placing tube, please do not bend the tube in order to avoid obstructing water flow (as the right Figure under). Besides, if needed, please use bend proof spring on the tube while bending it to avoid obstructing water flow efficiency. O O X 4-5 4-way Splitter Valve to the Tube on Waterblock Installation 4-5-1 Connect one side of tube 1 to 4-way splitter valve (1) A as it shows in the picture and fasten the tube clip.
English 4-5-3 Connect one side of tube 2 to 4-way splitter valve (2) B as it shows in the figure and fasten the tube clip. 4-5-4 Connect the other side of tube 2 to the inlet of waterblock and fasten the tube clip. The 2 splitters in the middle of 4-way splitter valve can be used to support VGA, chipset liquid cooling system or other liquid cooling system.
English 4-6-2 Connect the other side of tube 3 to the inlet of radiator and fasten the tube clips. 4-7 Radiator to the Inlet of Water Tank 4-7-1 Thread Tube 4 through the hole on PCI slot to connect one side of tube 4 to the outlet of radiator and fasten the tube clips. 4-7-2 Connect the other side of tube 4 to the inlet of the tank and fasten the tube clips.
English 4-9 Waterblock Installation Please make sure to take off the“CAUTION”sticker and apply the grease on the CPU surface evenly. Note: AMD K8 Bracket can be removed from waterblock (as Figure a) to adjust the appropriate installation direction. (as Figure b/c) Figure a Figure b Figure c 4-10 Intel® Pentium® 4 LGA775 Bracket Installation 4-10-1 Figure a 12 ® ® Replace AMD K8 Bracket with Intel Pentium 4 LGA775 Bracket (accessory No. ® ® 11) ( Figure a ).
English 4-10-2 ® ® Secure Intel Pentium 4 LGA775 motherboard with attached spring screws. 4-11 AMD K8 Clip Installation 4-11-1 Align the AMD K8 Clip to three raised points on the CPU. 4-11-2 Push down the bar to surely secure. 4-12-2 Push down the bar to surely secure. 4-12 AMD AM2 Clip Installation 4-12-1 Align the AMD K8 clip to the raised point on the CPU .
English 4-13 Fasten 4-way Splitter Valve 4 -14 MOSFET Air Cooling Fan Installation 4-13-1 Using the nylon tie to fasten 4-way splitter valve on trestle of the chassis. If there is no trestle available, try to find an applicable place to fasten it. 4-14-1 Place MOSFET air cooling fan on the top of waterblock and make sure that four feet of the air cooling fan are secured on waterblock. 4-14-2 Plug the power cord of MOSFET air cooling fan to the socket on motherboard CPU fan.
English 4-15 Pump Power Cord Installation 4-15-1 Prepare Pump Power Cord a : 6-pin connector b : female 2-pin connector c : male 2-pin connector d : 4-pin connector A C D 4-15-2 Connect the Power SW (female 2- pin c onnec tor) f rom the chassis’s panel with the pump power cord male 2-pin connector.
English 4-16 Fan Speed Control Box and Power Cord Instruction PCI Rear Fan Speed Control Box Connector Power Cord Fan Speed Control Box Socket Fan Speed Control Box Radiator Fan Speed Control Box Connector Socket Connect the other side of power cord with fan 1 to 2 power cord 4-17 Fan Speed Control Box Installation Tool needed: Fan Speed Control Box , Fan Speed Control Box Connect Line. 4-17-1 16 Thread the radiator fan connector through the hole of PCI rear fan speed controller.
Plug the radiator fan power cord into the fan speed control box. 4-17-4 To accomplish installation, plug the power cord of fan speed control box into the connector on the fan speed control box (as Figure a) and plug the other side of the power cord into the available 1 to 2 socket (as Figure b). Figure a Figure b 4-18 Heat Sink Installation 4-18-1 Heat sink( 8 pcs) can be pasted on the small chips on the motherboard or VGA card to lower the temperature.
English 5.Liquid Cooling System Installation and Test Before pouring liquid coolant into the tank to test the liquid cooling system, please remove the tank from the chassis to avoid damaging other components. Before turning on the power, please confirm that all the tube clips are fastened; leakage of liquid coolant due to improper installation may damage the system that is not covered by warranty.
Turn on the power until all liquid coolant drains into the tubes; the red light on the bottom of the PCB will blink and bleep; the system will turn off automatically within 4 seconds. (This is normal or initial refilling of liquid coolant since the tube and radiator are not full of liquid.) 5-1-3 Open the lid of the tank again to refill the tank with liquid coolant and than close the lid. Turn on the power one more time and repeat this step until the water is no longer lower than the low water-level.
English 5-2-3 To accomplish liquid cooling system, align the 2 screw holes on the radiator rack to the 2 screw holes on the power supply and fasten them up. With GIGABYTE™ 3D Aurora, Triton, Poseidon series, water tank can be placed inside of the chassis. [use 2 screws (b), please refer to accessories list] Velcro could be used to place the tank while using the chassis other than 3D Aurora, Triton and Poseidon series. 6.
English 6-1-3 Release the clip of waterblock from CPU. (Caution: Do not remove the tube at this point) 6-1-4 Cut and remove the nylon tie which is used to fasten 4-way splitter valve. 6-1-5 Remove pump + tank and 4-way splitter valve from the chassis; and set a pail on a lower position to fill the coming out coolant. 6-1-6 Release the tube clip on the inlet of the waterblock; and place the waterblock on the top of the pail.
English 6-1-9 Remove tube from PCI slot and be careful to avoid the leakage. Let the coolant drift into the pail. For the tube on the other side of radiator, please repeat this step until all the coolant drifts out. 7. 4-way Splitter Valve Instruction and User Manual (Adding VGA waterblock and chipset waterblock without disassembly) Ex. GIGABYTE™ blue eye and chipset waterblock 7-1 Remove the caps and tube clips from 4-way splitter valve. Do not switch on at this point.
Cut a tube into suitable size; connect one side of the tube with the second splitter on 4-way splitter valve(1) and connect the other side with the outlet of chipset waterblock and fasten the tube clips. 7-5 Cut a tube into suitable size; connect one side of the tube with the first splitter on 4-way splitter valve(2) and connect the other side with the inlet of chipset waterblock and fasten the tube clips.
English
