Macaron N Series SM-MSN09-C01 NFC Controller Module with Integrated Antenna Datasheet Version 1.0 Smart Approach Co., Ltd. 4F,No.669,Sec.4.Chung Hsing Rd., Chutung, Hsinchu 310, Taiwan, R.O.C. +886-3-5830303 www.smart-approach.com.
SM-MSN09-C01 Datasheet Smart Approach Co., Ltd (“S.A.”) retains the right to make changes to its products or specifications to improve performance, reliability or manufacturability. All information in this document, including descriptions of features, functions, performance, technical specifications and availability, is subject to change without notice at any time. While the information furnished herein is held to be accurate and reliable, no responsibility will be assumed by Smart Approach for its use.
SM-MSN09-C01 Datasheet FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SM-MSN09-C01 Datasheet 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加 大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信 法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 機設備之干擾。 Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only.
SM-MSN09-C01 Datasheet Revision History This section describes the changes that were implemented in this document. The changes are listed by revision, starting with the most current publication. Revision 1.0 Revision 1.0 of this datasheet was published in June 2014. This was the first publication of the document. -5- Revision 1.
SM-MSN09-C01 Datasheet Contents REVISION HISTORY ............................................................................................................................. - 5 CONTENTS ........................................................................................................................................... - 6 FIGURE CONTENTS ............................................................................................................................ - 7 TABLE CONTENTS ...................
SM-MSN09-C01 Datasheet Figure Contents Figure 1 Typical Application ................................................................................................. - 9 Figure 2 Typical Application II ............................................................................................ - 10 Figure 3 Module Block Diagram ........................................................................................ - 11 Figure 4 Transmission Modes ...........................................................
SM-MSN09-C01 Datasheet 1 Introduction This document consists of descriptions and specifications for both functional and physical aspects of the SM-MSN09-C01 NFC reader / writer module. In addition to the datasheet, Smart Approach maintains and extensive device-specific library of support and collateral materials that you may find useful in your application.
SM-MSN09-C01 Datasheet 2 Product Overview SM-MSN09-C01 is full featured NFC controllers designed for integration in portable equipment. It is optimized for low power consumption with fully host controllable power states and for small footprint for portable equipment applications. The module’s compact, flexible design with and exposed pad is optimal for size-sensitive applications, assures robust performance. The following illustration shows a high-level, generic view of a SM-MSN09-C01 application.
SM-MSN09-C01 Datasheet Figure 2 Typical Application II SM-MSN09-C01 can be connected on a host controller through I2C-bus interfaces. The logical interface towards the host base band is NCI-compliant with additional command set for SA specific product features. SM-MSN09-C01 can be connected to a UICC through an SWP interface. The SWP physical interface is compliant with ETSI/SCP SWP and HCI.
SM-MSN09-C01 Datasheet 3 Functional Descriptions This section provides detailed information about how SM-MSN09-C01 module works, what configurations and operational features are available. The following illustration shows the primary functional blocks of SM-MSN09-C01 module. Figure 3 Module Block Diagram Loop Antenna is Smart Approach customize solution, Antenna size of SM-MSN09-C01 is 40mm x 50 mm. Antenna matching is also a customize solution.
SM-MSN09-C01 Datasheet Figure 4 Transmission Modes For contactless card functionality, SM-MSN09-C01 can act autonomously if previously configured by the host in such a manner. PICC functionality can be supported without device being turned on or even with battery removed. 3.
SM-MSN09-C01 Datasheet 4 Electrical Specifications This section provides the DC characteristics, AC characteristics, recommended operating conditions. It includes information on the various timing functions of the module. 4.1 Pin Description The following Table shows the pin description for SM-MSN09-C01 module. The connection ground is internally connected and should be connected to GND on the main board as well. Table 1 Module Pin Description PIN No.
SM-MSN09-C01 Datasheet 4.2 I2C Address SM-MSN09-C01 I2C 7bit address is defined to 0x28. To write data, this module is addressed using 0x50, to read data, this module is addressed using 0x51. Table 2 I2C Address I2C address (R/W=0, write) I2C address (R/W=1, read) 0x50 0x51 4.3 Temperature Maximum Ratings Thermal specifications for this module have been modeled using a two-layer test board.
SM-MSN09-C01 Datasheet 4.5 Antenna Specifications Antenna specifications for this module have been modeled using a two-layer test board. Table 5 Antenna Specifications Value Item DC Resistance AC Impedance Frequency Q factor Antenna Type Size Min Typ Max 0.5 1 2 Unit Note Ω Ω 50 13.06 13.56 14.06 25 30 35 VSWR <2 MHz Add the Ferrite sheet FPC Loop Coil Normal: (40 ±0.5) X (50±0.5) mm 4.
SM-MSN09-C01 Datasheet 4.7 Thermal Protection Table 7 Thermal Protection Symbol Parameter Conditions Temperature TOVERTEMP protection trigger Min Typ Max 120 125 130 Unit 0 C 4.8 System power modes Table 8 System Power Modes Description Mode Full power mode Low-power mode Powered by the Field Power Off mode - 16 - Description The battery supply (VBAT) as well as the pad supply (VDD_IO) is available, all use cases can be executed The pad supply (VDD_IO) is not available.
SM-MSN09-C01 Datasheet Table 9 Power Mode Configuration VBAT VDD_IO VEN Power mode Off Off X Power Off mode On X Off Power Off mode On Off On Low Power Mode On On On Full power mode Note: X: Don’t care 4.9 Reset and download concept To enter reset there are 2 ways: - Pulling VEN low (Hard Power Down state) - If VBAT monitor is enabled: lowering VBAT below the monitor threshold (monitor mode, if VEN is kept above 1.
SM-MSN09-C01 Datasheet 4.10 NFC Connection Recommendation Figure 6 Connection Recommendation 4.11 Main Board Design Reference Figure 7 Main Board Design W/O UICC Reference - 18 - Revision 1.
SM-MSN09-C01 Datasheet 5 Ordering Information Table 11 Ordering Information Table Order Number Descriptions SM-MSN09-C01 NFC Macaron Module (NXP NPC100) with Integrated Antenna Dimension Module: 40x50x1.5 mm - 19 - Revision 1.
SM-MSN09-C01 Datasheet 6 Reliability Verification Table 12 Reliability Item Table No.
SM-MSN09-C01 Datasheet 7 NFC Module Outline The following illustration shows the package drawing for SM-MSN09-C01 module. The drawing contains the detail views, dimensions, tolerances, and notes. Pin 1 Figure 8 Antenna Module Drawing - 21 - Revision 1.
SM-MSN09-C01 Datasheet Figure 9 Module FPC Connection Footprint (Button Contact) Figure 10 FPC Wire Dimension - 22 - Revision 1.
