GN -AP1 0 1 B Wire le ss Ac c e ss Point U se r Guide http://www.gigabyte.com.tw Rev.1.
Safety, Care and Regulatory Information Important safety instructions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. The plug-socket combination must be accessible at all times because it serves as the main disconnecting device.
• • • Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack. Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. Do not use this product near water, for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement or near a swimmin g pool.
/ For European users only / European Community Directive Conformance Statement This product is in conformity with the protection requirements of EC Council Low Voltage Directive (Safety) 73/23/EEC, EMC Directive 89/336/EEC on the approximation of the laws of the Member States relating to electro-magnetic compatibility.
Contents 1. INTRODUCTION....................................................................................................1 1-1. CONTENTS OF YOUR SHIPMENT ...........................................................................1 1-2. PHYSICAL INTERFACE ..........................................................................................2 1-3. ACCESS POINT LED INDICATORS .........................................................................2 1-4. KEY FEATURES ....................................
1. Introduction GN-AP101B access point makes wireless networking a practical reality in more places, more companies and more environments than ever. Thanks to robust, secure, industry-standard 802.11b wireless networking, you can build networks that were previously far too expensive or too complex. The Gigabyte Wireless system can connect PCs throughout your premises without the headache of running cable.
1-2. Physical Interface One Ethernet LAN Port RJ-45, Auto-sensing and Auto-MDI/MDIX for 10/100M Ethernet LAN connection Init Button Initial reset (Init to factory default) Wireless antenna One 2.4 GHz antenna - IEEE802.11b Wireless solution Intersil Prism2.5 Power 1-3. Access Point LED Indicators Power LED (Green light) The Power LED lights up when power is on. Wireless LED (Green light) On The wireless function is acting. Flicker Data is being transmitted/received.
1-4. Key features Compatible with IEEE 802.11b Standard Auto data rate for 11/5.5/2/1Mbps 802.1D transparent Bridge Operation Channels for US/Canada, ETSI, and Japan. Support Nonpublic SSID Firmware update through AP manager By TFTP Roaming support MDI/MDIX: Auto crossover detect DHCP Client support Support Passphrase string Key. 40(64), 128 bits WEP privacy Support MAC filter 1-5. Specifications Feature Value Communication Standard IEEE802.11b Wireless LAN IEEE 802.3 10 Base-T Ethernet IEEE 802.
2. Installation Follow these steps to install the GN-AP101B Wireless Access Point. 1. Choose a proper place for GN-AP101B Wireless Access Point. In general, the best location is at the center of your wireless coverage area, within line of sight to all wireless devices. Keeping clear of metal obstructions and away from direct sunlight. 2. Place the GN-AP101B in the desired location. Normally, the higher you place the antenna, the better the performance will be.
There are two installation mode for your reference as follow： Static IP address Method 1 If you are Not using a DHCP server in your network, you can configure the AP by connecting to the computer directly. PC (AP Manager) 192.168.1.x DHCP (Disable) 192.168.1.1(default) GN-AP101B 1. You will need to assign a Static IP Address to the computer that you are using to configure the GN-AP101B on the same subnet. For instance, the default IP address of the GN-AP101B is 192.168.1.1 and the subnet mask 255.255.255.
Method 2 If require to setup as many GN-AP101B at the same time. You can setup a DHCP Server and let it assign IP to all the GN-AP101B so it has its own unique IP address. After the setup is finished, and then remove or disabled DHCP Server at last. Now, you can use the AP Manager to find all GN-AP101B in your network, and then setup the N-AP101B as static IP address one by one. Notice: After assign static IP address to every GN-AP101B, be sure to set the PC (AP Manager) to the same subnet.
3. Access Point Manager The Gigabyte Access Point Manager is used to configure Gigabyte Access Points. Note: The performance of wire line link is better than wireless link between the AP Manager and each Access Point. To use the wire line link to manage the GN-AP101B is recommended. 3-1. Installing the Access Point Manager Please follow these steps to install the GN-AP101B AP Manager in the Windows. Step1. Insert the GN-AP101B installation CD and click Install Gigabyte AP Manager on the CD autorun screen.
Step3. Click “Next”. Step4. Type the User Information then click “Next”.
Step5. Click “Next” to accept the default directory or “Browse” to another location. Step6. Click “Next”.
Step7. Click “Next”. Step8. Please wait a while.
Step9. Click “Finish” to complete setup.
3-2. Using the Access Point Manager You can launch Gigabyte AP Manager through Start \ Programs \ Gigabyte AP Manager Utility \ Gigabyte AP Manager. Enter the default password “admin” and click “OK”. It will automatically search for GN-AP101B Access Points on the same subnet when you open the Gigabyte AP Manager. You may click the icon to searching for Access Points manually.
Tree structure ESSID (ap101b) AP Name (AP101B) MAC Address (0020ED001700) Menu bar Tools Allow you to “Search” for AP by ESSID, AP Name, MAC Address, and IP Address and “Connect to AP by IP”. And allow you to “Save”, “Load” the AP configuration and “Copy”, “Paste” the configuration at the current page. Besides, it includes both “System Reboot” and “Load Default”. Password Allow you to change the AP Manager password and set the SNMP community string. About An online help and the AP Manager version.
Tool bar Find Access Point Connect To AP By IP Save AP Configuration Load AP configuration Page Copy Page Paste System Reboot Load Default - Find Access Point: Find all AP in the same subnet. - Save AP Configuration: Save all setting of the AP to a temp file. - Load AP Configuration: Load the setting of the temp file that you saved before to the current AP. - Page Copy: Copy the setting of the current page. - Page Paste: Paste the setting you has copied to the current page.
System Page The System Page displays the Device_Information and the Change Community String function. Device_Information The Device_Information include the AP name, MAC address, device description, the version information and the device type. You can change the AP Name to whatever unique name, which can represent this AP. Change Community String This function can let you change the community string to the AP.
Init button In case you forget the community string, you have to press the AP init button and then the AP setting (include community string) will be restore to default value. Note: The SNMP community string defines the relationship between an SNMP manager system (AP Manager) and the agent systems (all APs). This string acts like a password to control the AP Manager to access the AP. The default value of the community string is “public”.
IP Config Page Obtain an IP address automatically You can check this selection to get IP address from the DHCP server automatically in you network. Use the following IP address You can check this selection to assign IP address by yourself. The default IP address is 192.168.1.1 and the subnet mask is 255.255.255.0. Please make sure the assigned IP address is unique in your network. After you change the IP address of the AP, please also change the PC’s (AP Manager) IP address to the same subnet.
Wireless Operation Page Normally, you can have the wireless works smoothly even you didn’t change any item in this page. Region Because of the different region has a different open channel regulation, please check whether the default region value is your local area. If it did not appear properly region please contact your local distributor or authorized reseller immediately. Channel ID Please choose the channel, which you can get best performance. Normally, it doesn’t need to change.
Auto Rate In this item you can select either “enable” or “disable”. The default value is “enable”. Enable: If the selection is “enable”, the transfer rate will automatically change to the optimum rate allowed. The range of auto-change will base on the setting of “Transmit Rate”. Transmit Rate setting: 11M: range is among 1M, 2M, 5,5M and 11M 5.5M: range is among 1M, 2M and 5,5M 2M: range is between 1M and 2M 1M: no auto-change. The transmit rate is fixed at 1M.
Encryption Page This page is the security configuration of the wireless connection. WEP (Wired Equivalent Privacy) is a data privacy mechanism based on a 64/128-bit shared key algorithm, as described in the IEEE 802.11 standard. When the “Disable” is selected there is no WEP encryption. When either “64bits” or “128bits” selected there is encrypted date transfer to prevent unauthorized user to access the wireless network. Authentication Type. You may choose between “Open System”, “Shared Key”, and “Both”.
64 (40) Bits or 128 (104) bits There are two levels of encryption 64 bits and 128 bits. The 64 bits encryption is referenced as a lower level encryption. The 128 bits encryption is referenced as a higher level encryption. The 64 bits WEP encryption use 40 bits as a secret key, which can controlled by user, and 24 bits as the initialize vector, which user can not control. These two portions plus together is 64 bits encryption. Some other vendor’s product might refer as 40 bits encryption.
Advance Page For enhance the security of the wireless network, this AP provide the MAC address filtering mechanism to prevent the unauthorized user access. Check “Enable MAC filter” and key in MAC address table, then only those MAC address in the table are allowed to connect to this AP. Enable MAC Filter Choose the “Enable MAC Filter” and click the “Add” button to add more MAC addresses or click “Remove” button to delete the MAC addresses from the Authorized MAC Address table.
Change AP Manager Password User can change the administration password of the AP manger to prevent other user access to the AP Manager. On the Menu Bar (Password->AP Manager Password) can invoke the password change dialog. Please enter a new admin password and confirm admin password then press “OK”. You have to enter this new password to log in when you want to use the AP Manager next time. Set Community String The community string defines the relationship between AP manager and the AP.
4. Upgrade Firmware You can download the upgraded firmware version from Gigabyte website. Run TFTP Program Step1. You can find the “Upgrade Tool” through Start \ Programs \ Gigabyte AP Manager Utility \ Gigabyte AP Upgrade. Step2. The Gigabyte Firmware Upgrade Tool screen will appear. Please enter the “AP IP address” which you want to upgrade the firmware. You can press “Ping” button to verify whether the AP is online.
Step3. Press “Open” button to choose the firmware then press “Upgrade” button to start the firmware upgrade process. Note: During the firmware upgrade, please DO NOT turn off the PC or AP and DO NOT unplug the Ethernet cable. Step4. After the AP device rebooting successful, the AP firmware upgrade is completed. Note: Right-Click on the screen, the content menu will be displayed. You can find the online help and the version information of the firmware upgrade utility.
5. Uninstall AP Manager Utility You can find the Uninstall program through Start \ Programs \ Gigabyte AP Manager Utility \. Step1. The InstallShield Wizard will appear then please wait. Step2. Click “Yes”. Step3. Click “OK” and then the Gigabyte AP Manager Utility has been uninstalled successfully.
If you just want to modify some program components or reinstall all program components, you can run the installation program directly. And then the InstallShield Wizard will appear. Please choose one of the options what you want then click “Next” continues to modify, repair or remove the Gigabyte AP Manager Utility.
Limited Warranty 1-Year Warranty Gigabyte warrants to the original consumer/purchaser that the product free from defects in material and workmanship for no limited time from the original manufactory shipment date. This warranty does not cover the product if it is damaged in the process of being installed or improperly used. Gigabyte may replace or repair the product with either new or reconditioned parts.
