Tracer 2000 Digital Video Recorder User’s Manual
Tracer 2000 DVR user manual Contents CHAPTER I INTRODUCTION...............................................................................................................5 LIMITED WARRANTY ...............................................................................................................................5 FUNCTION INTRODUCTION ....................................................................................................................5 FEATURE ...........................................
Tracer 2000 DVR user manual 1. Standard CMOS Features ....................................................................................................................24 2. Advanced BIOS Features .....................................................................................................................25 3. Advanced Chipset Features..................................................................................................................26 4. Integrated Peripherals ......................
Tracer 2000 DVR user manual Copyright Notice Copyright 2004. All Rights Reserved This document may not, in whole or in part, be reproduced or transmitted in any form or by means, electronic, mechanical, or optical, including photocopying, recording, or storing in a retrieval system, or translated into any language in any form without the prior written content of us.
Tracer 2000 DVR user manual CHAPTER I INTRODUCTION Thank you for purchasing Tracer 2000 DVR; this manual will guide you through the setup, installation, and use of all our DVR systems. Before proceeding, please read this manual thoroughly! If you have any questions or concerns that cannot be solved by following this manual, please visit our web site at http://www.giantec.net LIMITED WARRANTY Giantec Inc. warrants this product to be in compliance with its own plans and specifications.
Tracer 2000 DVR user manual FEATURE The TRACER2000 comes with the following hardware devices: Control panel with IR receiver One10/100Mbps RJ-45 Ethernet Port One RS 232 and one RS232/422/485 selectable interface One VGA Connector One speaker out Two USB Ports Two 3.
Tracer 2000 DVR user manual CHAPTER II PACKAGE Packing List Check the accessories accompany with the system you purchase as listed below. With newer package release, the accessories are compacted into an accessory box. Please check the items and Contact to your dealer you bought from if any of them is missing TRACER2000 System Power Cord Screws Pack Remote Commander Battery (AAA) X 2 User’s Manual Installation CD-ROM Please keep the packaging materials. You may need them for the use of further service.
Tracer 2000 DVR user manual CHAPTER III INSTALLATION FRONT PANEL VIEW Alarm Menu Playback Display IR UP Removable Air LEFT Filter Bracket Confirm Removable Air RIGHT Filter Bracket DOWN ※Remove and clean up Air Filters monthly is essential. REAR PANEL VIEW Power supply Parallel port GPIO Audio MIC1 MIC2 MIC3 MIC4 ALARM IN ALARM OUT 1 2 3 4 1 2 3 4 CH1 CH9 1 COM1 Version 3.
Tracer 2000 DVR user manual 1 INDICATOR Power LED Power LED: Green light shows power is on. Status LED: Green light continuous on means working properly. Status LED Green light blinking shows status of recording Red light continuous on means no signal (This may implies HDD damaged, No Power, or Access Error.) Red light blinking shows status of recycling. (HDD space less than 1 Gigabyte) 2 CABLE CONNECTION Following is the basic device must be prepared before to start installation complete system. 1.
Tracer 2000 DVR user manual 2.2. Connect Camera Cable to BNC connector 2.3. Connect to LAN connector: Plug RJ-45 connector to LAN Port 2.5.1 Insert RJ-45 cable to network LAN socket on the rear. 2.5.2 Connect Serial port modem to serial connector (COM1) and through Dial-in function to connect to Internet. Version 3.
Tracer 2000 DVR user manual 2.4. Connect to Printer Port (option) There are two types of Printer port. One is LPT the other is USB. Connect Port as show below: USB Port Version 3.
Tracer 2000 DVR user manual 3. POWER CONNECTOR 3.1. Connect power cord (110V~240V auto switch) into the power socket. Press “I” to start up system... Pushes switch “I” to turn it on. Version 3.
Tracer 2000 DVR user manual CHAPTER IV Pin assignment Internal Jumpers and Connectors Version 3.
Tracer 2000 DVR user manual Power Switch for ATX power supply (JP1) Signals Power ON/OFF JP1 1-3 Reset/LED/Speaker (JP1) Signals JP1 Power LED, Pin 9+, Pin109-10 External speaker 14-20 HDD LED, Pin8+, Pin77-8 System reset switch 5-6 SUSLED Pin4+, Pin22-4 PS. For the AT system (short pin 10 & pin12) for power on Internal USB connector (USB2) Signals Power Data Data + USB GND CHS GND USB2-1 1 3 5 7 9 USB2-2 10 8 6 4 2 Power connector (P1) Signals +12V +5V -12V -5V +3.
Tracer 2000 DVR user manual CPU FSB Select (JP4) Function Auto by CPU 66 MHz JP4 1-3, 2-4 3-5, 4-6 Function Sense +12V PWM control FAN1,2 3 2 1 FAN control (FAN1, 2) HDD Connector (IDE1, 2) 39 40 Version 3.0 1 2 Pin no. Signal Pin no. Signal 1 - RST 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 N.C. 21 N.C.
Tracer 2000 DVR user manual Parallel/Printer connector (PRN) Pin no. Signal Pin no. Signal 1 Strobe 10 -Acknowledge 2 Data 0 11 Busy 3 Data 1 12 Paper Empty 4 Data 2 13 + Select 5 Data 3 14 - Auto Feed 6 Data 4 15 - Error 7 Data 5 16 - INIT Printer 8 Data 6 17 - Select Input 9 Data 7 18-25 Ground Video Input (J2) 1 2 43 44 Pin no.
Tracer 2000 DVR user manual General Purpose Input / Output (J3) 2 1 Pin no. 1 3 5 7 9 11 13 15 signals GPIO-0 GPIO-1 GPIO-2 GPIO-3 GPIO-4 GPIO-5 GPIO-6 GPIO-7 Pin no. 1 2 3 4 5 signals VCC IRRX GND IRTX CIRRX 16 15 Pin no. 2 4 6 8 10 12 14 16 signals Audio IN3 AGND Audio IN2 AGND Audio IN1 AGND Audio IN0 GND(for GPIO) Version 3.
Tracer 2000 DVR user manual PCI bus pin assignment B62 B52 B49 SOLDER SIDE B1 A62 A52 A49 COMPONENT SIDE A1 Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Version 3.
Tracer 2000 DVR user manual External Connector CRT Display Connector (VGA) 5 15 1 10 Pin no. Signal Pin no. Signal 1 RED 9 N/C 2 GREEN 10 GND 3 BLUE 11 N/C 4 N/C 12 N/C 5 GND 13 H-SYNC 6 GND 14 V-SYNC 7 GND 15 N/C 8 GND Audio Input connector: MIC1 MIC2 MIC3 MIC4 GPIO connector: 1 USB connector: USB Ports Pin 2 3 4,8 1,5 6 7 Version 3.0 Name USB0 + USB0 GND USB power USB1 + USB1 - 2 3 4 5 6 7 8 Pin no.
Tracer 2000 DVR user manual COM 1 Connector 1 6 5 9 RS-232 Connector (COM1) Pin no. Signals 1 DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI COM2 Connector 1 6 5 9 RS-232/RS-422/RS-485 Connector (COM2) (Please setup mode type by JP3) Version 3.0 Pin no.
Tracer 2000 DVR user manual Ethernet connector (RJ-45) Drawing of Ethernet connector RJ-45 Pin no. 1 2 3 4 5 6 7 8 signals TX+ TXRX+ NC NC RXNC NC Connectors The connectors allow this main board to connect with other parts of the system. Some problems encountered with your system may be caused by loose or improper connections. Ensure that all connectors are in place and firmly attached.
Tracer 2000 DVR user manual P/T/Z Setting The P/T/Z Setting complies with LILIN or PELCO. Protocol has been previously attached to the COM ports. You may control the camera via arrow buttons. In this case, you don’t need to buy dedicated P/T/Z controller. Pin assignment of COM2： Connect 9 PIN Female D_SUB to COM2 (Pin defines as below) Cable connection：Camera Input jack to COM2 for PIH-7000/7600： For example: Jumper setting of COM2： The system default of COM2 is RS-485.
Tracer 2000 DVR user manual CHAPTER V CMOS SETTING Introduction This manual discusses Award™ Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off.
Tracer 2000 DVR user manual 1. Standard CMOS Features Use this menu for basic system configuration. Date: Time: IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Driver B Video Halt On Mon.
Tracer 2000 DVR user manual 2. Advanced BIOS Features Use this menu to set the Advanced Features available on your system.
Tracer 2000 DVR user manual 3. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance.
Tracer 2000 DVR user manual 4.
Tracer 2000 DVR user manual 5.
Tracer 2000 DVR user manual 6. PnP / PCI Configuration This entry appears if your system supports PnP / PCI. CMOS Setup Utility – Copyright © 1984-2000 Award Software PnP/PCI Configurations Item Help Disabled Reset Configuration Data -----------------------------------------Menu Level Auto(ESCD) Resources Controlled By Press Enter X IRQ Resources Default is Disabled.
Tracer 2000 DVR user manual 7. PC Health Status Use this menu to monitor the CPU and system temperature, CPU fan speed the voltage of the onboard regulators. CMOS Setup Utility – Copyright © 1984-2000 Award Software PC Health Status CPU Warning Temperature Disabled Item Help Current System Temp.
Tracer 2000 DVR user manual 9. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While Award has designed the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. . Load Optimized Defaults (Y/N)? N Pressing ‘Y’ loads the default values that are factory settings for optimal performance system operations. 10.
Tracer 2000 DVR user manual CHAPTER VI System HDD Installation Guide Follow the step to setup HDD drawing box. 1. Remove the screws on the case. (marked in while circles) Remove the screws on the case. Version 3.
Tracer 2000 DVR user manual 2. Take off the upper cover and remove the screws. Remove the screw. Version 3.
Tracer 2000 DVR user manual 3. Remove HDD Tray, and install HDD properly. Version 3.
Tracer 2000 DVR user manual 4. Insert the assembled HDD tray into TRACER2000, and connect both Power and HDD cables. Version 3.
Tracer 2000 DVR user manual 5. Assemble the upper cover and the screws. Version 3.
