Installation & Assembly

Clear Vinyl
Tubing.
Secure to
copper
connection
110V 3 prong power cord. Plug
into 110v GFCI outdoor outlet.
Turn blue knob to adjust water
ow.
Steel Bar (on back of
ftn) used for securing
fountain to wall, fence,
or post. Steel wire
recommended for
securing
Slide power
cord through
rubber
stopper and
secure
rubber
stopper in
the 2” PVC
coupling.
Check for
tight t to
avoid leaks.
Hard Surface such as a
concrete pad, compacted
pea gravel, paver stones, or
bricks
www.GianniniGarden.com
[e-mail]
CAUTION:
~ Excessive weight or pressure on the fountain may cause it to fall. KEEP CHILDREN AND OTHERS FROM CLIMBING,
SITTING OR LEANING ON THE FOUNTAIN AND ITS COMPONENTS.
G-280 Pump w/
water-ow
adjustment knob.
Step 1
Step 2
Step 3
Step 4
Step 5
Clear Vinyl
Tubing
3 prong
power cord
Small Turn-
Buckle
Eye Bolt
G-280 Pump
Steel Securing Bar
Side View
Wall, Fence, or Post
PVC
Threaded
Elbow
(back of
fountain)
Installation Instructions:
1. Read the “How to Maintain Fountains” instruction sheet
included with your shipment. (On reverse side)
2. Place base of fountain on a hard or solid surface, such as a
conrete pad, pavers stones, bricks, or compacted pea gravel.
Make sure base is level with the ground. If not level, place a shim
under to level
3. Place basin on top of base and center.
4. Place pump in left compartment towards rear of basin. Drape
pump cord over basin and run along back of base so it is not
visible.
5. Connected clear vinyl tubing to nozzle on pump and secure.
Temporarily drape tubing over back of bowl.
6. With two or more people, lift top component of fountain and
place on top of basin as shown. To ensure that there is no
damage, place burlap (used for packaging) around edges of
basin.
7. Cut tubing to length and attach to PVC elbow on back of ftn.
8. Secure top of fountain to a wall, post, or fence using supplied
turn-buckle and eyebolt. Turn buckle should attach to the steel
bar towards the top and back of fountain.
9. Fill basin full of water and plug in pump. Adjust water ow
using blue dial on front of the pump.
10. Enjo
y your new Giannini fountain!
11. E-mail a picture of your installed fountain to
[e-mail] for a 10% o coupon on a future
purchase.
Hard Surface.
(See Step 2)
Hard Surface such as a
concrete pad, compacted
pea gravel, paver stones, or
bricks. If surface is not
exactly level, wood or
plastic shims may be used
to level founain.
Slide power cord through rubber
stopper and secure rubber stopper in
the 2” PVC coupling. Check for tight t
to avoid leaks.
Giannini adjustable
pump. Turn blue nob to
reach desired water ow.
110V 3 prong
power cord. Plug
into 110v GFCI
outdoor outlet.
Cut 5” piece of PVC
tubing and place in hole
uder ball. Tubing should
go inside hole on top of
column
Clear Vinyl
Tubing
Connect clear tubing to hole inside
column. Tubing should extend only
2-4 inches inside column.
www.GianniniGarden.com
[e-mail]
CAUTION:
~ Excessive weight or pressure on the fountain may cause it to fall. KEEP CHILDREN AND OTHERS FROM CLIMBING,
SITTING OR LEANING ON THE FOUNTAIN AND ITS COMPONENTS.
See Back for Fountain Care
Instructions
CAUTION:
~ Excessive weight or pressure on the fountain may cause it to fall. KEEP CHILDREN AND OTHERS FROM CLIMBING,
SITTING OR LEANING ON THE FOUNTAIN AND ITS COMPONENTS.
www.GianniniGarden.com
[e-mail]
Hard Surface such as a
concrete pad, compacted
pea gravel, paver stones, or
bricks. If surface is not
exactly level, wood or
plastic shims may be used
to level founain.
110V 3 prong
power cord. Plug
into 110v GFCI
outdoor outlet.
Slide power cord through rubber
stopper and secure rubber stopper in
the 2” PVC coupling. Check for tight t
to avoid leaks.
Clear Vinyl
Tubing
Connect clear tubing to hole inside
top neal. Tubing should extend
only 2-4 inches inside neal.
Giannini adjustable
pump. Turn blue nob to
reach desired water ow.
Place large bowl on
large pedestal. With
someone’s help, tilt
both the pedestal and
bowl together (very
slightly) to pull out
pump cord from
bottom of pedestal