Installation Guide

Please leave this sheet and warranty for the custo
mer for
future reference
Maintenance: Clean with warm water, soft cotton
cloth and non-abrasive liquid dish soap. Towel dry.
Never use acids, harsh abrasives, detergents, or
products containing chlorides on any parts of this
product.
Faucet Installation Instructions
Hole Diameters are 1
1
8
" minimum to 1
7
8
" (without esc
utcheon)
or 2
1
8
" (with escut
cheon) maximum.
Maximum deck thickness is 2
1
4
" (without escutcheon)
or 2
3
8
" (with e
scutcheon).
This faucet comes completely assembled and water tested
.
Includes copper supply lines with 1/2" IPS inlets.
Tools required-channel lock pliers (or pipe wrench), basin wrench, small
crescent wrench and Teflon tape.
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Fri
day
Pleas
e leave this
sheet and warranty f
or
the c
ust
omer for future reference
Insert
lift rod (6A) into strap (6B) and
tigh
ten
screw (6C).
Step 6
6
A
Figure 2
Faucet Installation Instructions
Step 3
Install Pop-up Assembly. Remove
stopper (3A) and flange (3B).
Screw nut (3C) all the way down.
Push gasket (3D) down.
3D
3C
3A
3B
6B
6C
Page 2Page 1
4D
4C
4B
Step 4
Apply silicone sealant to the underside
of flange (4A). Apply teflon tape to
threads at the top of body (4B). Insert
body (4B) into sink. Screw flange onto
body. Pivot hole (4C) must face the
back of the sink. Tighten nut (4D), do
not overtighten. Clean excess silicone
sealant.
4A
Shut off water supply prior to beginning installation.
Make connections to 1/2" IPS
water lines (2A, not included). Use
wrenches to tighten connections.
Do not overtighten.
Step 2
Step 5
Remove pivot nut (5A). Install
horizontal rod (5B) and stopper
(5C) as non-removable (5D). Hand
tighten pivot nut (5A). Attach
horizontal rod to strap (5E) using
clip (5F).
5A
5B
5C
5D
5E
5F
Important: After installation is completed
t u r n f a u c e t o n f o r t w o minutes to flush
out any debris from the water lines.
While water is running check for leaks.
Step 7
Figure 3 Figure 4
Figure 5
Fig
u
r
e 6
Figure 7
BN
VB
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
2A
2A
LL800 LL800
Insert faucet through sink with
escutcheon (1A) and base
plate (1B) above the sink. From
underneath slide on
washer and secure faucet by
tightening nut.
Step 1b Three Hole Mounting
Figure 1bFigure 1a
Step 1a Single Hole Mounting
Insert faucet through sink. From underneath
slide on washer and secure faucet by
tightening nut.
1A
1B
Vintage Bronze
*Specify
Finish
Brushed
N
i
c
kel PVD
Parts
Finish Codes
Pop-
up
Ass
embly Less L
i
ft
Rod
Us
e
for L
L
800-VB
Use for LL
800
-PC/BN
R
P
400
38*
R
P40
0
27
*
R
P56
0
51
Nut
R
P70228
M
e
t
al W
asher
R
P
2
0
03
1
C
artridg
e
R
P7
0
22
4
Ret
ainer Ri
ng
R
P80
1
8
4
* Cap
R
P50092
Conn
ect
o
r
R
P13
2
11
*
H
andle
R
P50002
Set Screw
R
P40
1
43
*
Li
ft Rod
R
P80
2
87
*
E
sc
ut
che
on
RP
802
88
B
a
s
e
P
l
ate
Figure 8
Step 8 (If Necessary)
Shut off water supply at angle stop and
unscrew the copper tubes from water
supply lines. Remove screen filter (8A)
from copper tubes (8B) and clean/rinse
off any debris. Reinstall (8A) into (8B) in
original direction, reconnect supply lines
and turn water on.
NOTE: Due to open trough design, the
aeration/screen filter has been added to
the supply lines. If flow becomes restricted
or pressure reduced, please proceed as
follows:
8B
8A
8A
8B
RP70072
Screen Filter
NOTE: Flat portion on hot water tube is a
design detail. It is solely for the ease of
installation and does not affect the function
or water flow of this faucet.
RP70072
Screen Filter
PC Polish Chrome