Installation Guide

Please leave this sheet and warranty for the customer for future reference
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
Maintenance: Clean with warm water, soft cotton
cloth and non-abrasive liquid dish soap. Towel
Dry.
Never use acids, harsh abrasives, detergents, or
products containing chlorides on any parts of this
product.
Faucet Installation Instructions
LL700
Hole Diameters are 1
1
8
" minimum to 2" (without escutcheon) or 2
1
8
" (with escutcheon)
maximum.
Maximum deck thickness is 2
1
4
" (without escutcheon) or 2
3
8
" (with escutcheon).
This faucet comes completely assembled and water tested.
Tools required-channel lock pliers (or pipe wrench), basin wrench, small crescent wrench
and Teflon tape.
Please leave this sheet and warranty for the customer for future reference
Figure 6
Insert lift rod (6A) into strap (6B)
and tighten screw (6C).
Step 6
6A
Figure 1bFigure 1a
Insert faucet through sink with flange (1A) above the sink. From
underneath slide on washer and secure faucet by tightening nut.
Step 1a Single Hole Mounting
Step 1b Three Hole Mounting
Faucet Installation Instructions
Important: After installation is
complete remove aerator and turn
faucet on for two minutes to flush
out any debris from the water lines.
While water is running check for
leaks. Replace aera
tor.
Step 3
Install Pop-up Assembly.
Remove stopper (3A) and
flange (3B). Screw nut
(3C) all the way down.
Push gasket (3D) down.
Figure 3
3D
3C
3A
3B
1A
Step 7
Figure 7
6B
6C
Page 2 Page 1
4D
4C
4B
Step 4
Apply silicone sealant to the underside
of flange (4A). Apply teflon tape to
threads at the top of body (4B). Insert
body (4B) into sink. Screw flange onto
body. Pivot hole (4C) must face the
back of the sink. Tighten nut (4D), do
not overtighten. Clean excess silicone
sealant.
Figure 4
4A
5F
5E
5D
5C
5B
5A
Figure 5
Remove pivot nut (5A). Install
horizontal rod (5B) and stopper
(5C) as non-removable (5D).
Hand tighten pivot nut (5A).
Attach horizontal rod to strap
(5E) using clip (5F).
Step 5
Shut off water supply prior to beginning installation.
2A
2A
Make connections to 1/2" IPS water
lines (2A, not included). Use
wrenches to tighten connections. Do
not overtighten.
Step 2
Figure 2
RP40027*
RP40038*
RP40050*
Lift Rod
Use for LL700-PC/BN Use for LL700-VB
Parts
RP13181*
Handle
RP50002
Set Screw
RP50095 Connector
RP80184* Cap
RP70224
Retainer Ring
RP20031
Cartridge
RP30055*
Aerator
RP70228
Metal Washer
RP56051 Nut
RP80229*
Flange
RP80227*
Escutcheon
RP80228
Base Plate
Includes copper supply lines with 1/2" IPS inlets.
LL700
Insert faucet through sink with escutcheon (1B) and base
plate (1C) above the sink. From underneath slide on
washer and secure faucet by tightening nut.
Finish Codes *Specify Finish
BN
Brush
ed Nickel PVD
VB
Vintage Bronze
Pop-up Assembly Less Lift Rod
1B
1C
NOTE: Flat portion on hot water tube is a design detail. It is solely for the
ease of installation and does not affect the function or water flow of this faucet.
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
PC
Polish Chrome