Installation Guide

Please leave this sheet and warranty for the customer for future reference
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
Maintenance: Clean with warm water, soft
cotton cloth and non-abrasive liquid dish
soap. Towl dry.
Never use acids, harsh abrasives or
detergents.
Faucet Installation Instructions
LL102-PC
Hole Diameters are 1
3
16
" minimum to 1
1
2
" (without escutcheon) or 1
3
4
" (with
escutcheon) maximum Maximum deck thickness is 2
3
8
" (without escutcheon) or 2
1
8
" (with escutcheon)
This faucet comes completely assembled and water tested
Includes braided stainless steel supply lines with 3/8" OD Inlets and 1/2" IPS
adapters (for use only when needed) Tools required-channel lock pliers (or pipe wrench), basin wrench, small crescent
wrench and Teflon tape
LL102-PC
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
Please leave this sheet and warranty for the customer for future reference
Figure 7
Insert lift rod (7A) into strap (7B)
and tighten screw (7C). Step 7
7A
Step 1 Install Pop-up Rod
Figure 1 Figure 2bFigure 2a
Figure 3
Push lift rod through hole in bottom of
body then reattach lift rod knob.
Step 3
Install lift rod into
faucet before
mounting faucet
on deck
Insert faucet through sink with flange (2A) above
the sink. From underneath slide on washer and
secure faucet by tightening nut.
Step 2a Single Hole Mounting
Step 2b Three Hole Mounting
Follow step 2a including deck plate
between flange and sink.
RP40098*
RP56012
RP70228
RP80199*
RP80198*
RP30077*
RP20005
RP50002
RP10056*
RP13156*
Faucet Installation Instructions
Important: After installation is
complete remove aerator and turn
faucet on for two minutes to flush
out any debris from the water lines.
While water is running check for
leaks. Replace aerator.
Step 4
Install Pop-up Assembly. Remove stopper (4A) and
flange (4B). Screw nut
(4C) all the way down.
Push gasket (4D) down.
Figure 4
4D
4C
4A
4B
i
n
g
a
i
G
i
n
g
a
i
G
2A
Connect hot and cold faucet supply lines
(3A) directly to the angle stops. Or
attach included 1/2" IPS adapters (3B)
to faucet supplies and connect to 1/2"
IPS water lines (3C, not included). Use
wrenches to tighten connections. Do
not overtighten.
Step 8
Figure 8
7B
7C
Page 2Page 1
RP40027*
3B
OR
ANGLE STOP
3A
3C
3A
5D
5C
5B
Step 5
Apply silicone sealant or plumber's putty
to the underside of flange (5A). Apply teflon tape to threads at the top of body
(5B). Insert body (5B) into sink. Screw
flange onto body. Pivot hole (5C) must face the back of the sink. Tighten nut
(5D), do not overtighten. Clean excess
silicone sealant or putty.
Figure 5
5A
6F
6E
6D
6C
6B
6A
Figure 6
Remove pivot nut (6A). Install
horizontal rod (6B) and
stopper (6C) as
non-removable (6D). Hand
tighten pivot nut (6A). Attach
horizontal rod to strap (6E) using clip (6F).
Step 6
Shut off water supply prior to beginning installation
Finish Codes
*Specify Finish
PC
Polished Chrome
1/2" IPS Adapters
For use only in
some installations
RP80028*
RP70215