com What is the LAMINATED GLASS? Laminated glass is a type of most safety glass, which is produced by bonding two or more layers of tempered glasses together with a plastic inter layer. The inter layer can keeps the layers of glass bonded into one piece even when broken, the pieces do not disperse or breaking up into large sharp pieces, keep the same shape as usual, leaving the surface clean and smooth , avoid injury accidents.
IMPORTANT GETPRO® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model's web page on getprohome.com for the latest technical drawings, installation manuals, warranty information or additional product details. This product should be installed by someone familiar with the construction requirements for this type of project and the care necessary for the safe installation and operation of the product.
ITEM REFERENCE IMAGE NAME ory & _— Bottom Guide Rail 1 0 Ip Guide Block 4 a NL Wall Profile Bumpers 6 oO Na Towel Bar 2 6 = Wall Profile 2 e Door Glass 2 @ ee Upper Guide Rail 1 € Roller Assembly 4 ° # Cover 2 i & Anti-jump Hook 4 @ Ey Wall Anchor 8 Zi id Truss Head Self-Tapping Screw/ ST4*30 8 & bY Truss Head Self-Tapping Screw/ M4*10 8 a fm Truss Head Self-Tapping Screw/ ST4*12 6 & & DO1 Screw cover 14 wewgetprohome.
TOOLS REQUIRED Power Drill 1/4= & 1/8" Drill Bits Tape Measure Phillips Screwdriver level < So Pencil Safety Goggles Mallet Silicone hacksaw MOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the DETAILS DIAGRAM, and packing list in this manual as a reference. Before discarding the carton, check for small hardware box that may have fallen to the bottom of the carton. If any parts are damaged or missing, please contact GET PRO for replacement.
INSTALLATION STEPS Step 1 Measure the actual width and cut the bottom and upper guide rail Measure the finished opening width at the bottom, middle and the top, also check the threshold for level and the walls for plumb. NOTE: Both bottom and upper guide rails to be shorter than the acts! measure size 0.2 inch, because i's fits between the wall profiles. www.getprohome.
Step 2 Place the bottom guide rail onto the threshold in the desired position. Check the threshold with a level and Use a tape measure align it evenly with the front edge and mark it’s position. IMPORTANT Make sure the bottom guide rail is horizontal and parallel to the threshold — 7 — www.getprohome.
Step 3 Position one wall profile against the wall onto the bottom guide rail. Check for plumb with a level and mark the screw positions.
Step 5 Place the wall profile sit firmly on the bottom guide rail, fix the left and right sides of the wall profiles with 6 screws. oid 9 IMPORTANT 1) Nate: Make sure that the bottom guide rail is parallel to the threshold surface again. www.getprohome.
—n Step 6 Please follow the screw holes installed three Wall Profile Bumpers on both Wall Profiles, and cover the holes with the decorative caps. www.getprohome.
Step 7 Install 4 Roller Assemblies onto the tops of both doors. mim om h w IMPORTANT 9 important TIP: Be sure this spare part face to the correct direction. It can help the glass ° door keep in the mass level when you hanging onto the upper guide rail. Guz Oud www.getprohome.
Step 8 Be sure to position the rollers facing in the correct direction for each door Two wheels facing OUT for the outside door glass, and two wheels facing IN for the inside door glass. Bring both glass doors into the shower area for hanging. Using padding to protect the glass and shower area. OUTSIDE NOTE: Da not attach the Towel Bars to the door glass until instructed. Do not attempt to Lift the glass with the towel bars as doing so may cause damage to the glass and/or serious personal injury.
Step 9 Install the upper guide rail onto the installed wall profiles, the steps as following: firstly use the cover mark the hole on the wall, remove it then insert the green wall anchor, fix the cover on the upper guide rail, place this preset upper guide rail sit firmly onto the installed wall profiles, finally fixed tighten by screws.
— 15 step 10 Lift and insert the outer door glass up into the upper guide rail so the Roller Assemblies fit into the groove inside the rail. Carefully lower the Upper Guide Rail so the glass door slides into the proper slot. Next, Install the inner glass door in the same manner. Slowly move the installed door to the opposite end, lift the Upper Guide Rail, and install the inner glass door into the Upper Guide Rail.
Step 1 Make sure the Bottom Guide Rail is level, move both glass doors to the opposite end, attached the Guide Block and Bottom Guide Rail to the threshold using four of the screws. Cover the screw holes with the decorative caps. IMPORTANT: There's two holes in the middle of the Bottom Guide Rail, Please follow this two holes install two Guide Blocks, The other two Guide Blocks must against the wall profiles to installed. Slowly move two glass doors into the groove of the Guide Blocks.
step 13 Make sure if the glass doors are level, if not, please rotate the wheels, adjust the glass doors to the same height, fix the anti-jump hooks onto the wheels. Rotate left and right to adjust the glass height — 17 — www.getprohome.
Step 1 4 Apply good quality mildew-resistant silicone to the entire exterior and interior perimeter glass panel where meets the wall and along the threshold. Allow 24 hours for the silicone to fully cure before using the shower. Allow 24 hours for the silicone to fully cure before using the shower. www.getprohome.
GET PRO Questions, problems, missing parts? Before returning to the store, contact GET PRO Customer Service Retain this manual for future use. BET PRO’ is registered trademarks of GET PRO E-COMMERCE INC.
