V100 USER’S MANUAL Rugged Mobile Computing Solutions
March 2013 TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice. For the latest version of the manual, please visit the Getac website at www.getac.com.
Table of Contents Chapter 1 Getting Started ............................................................. 1-1 Getting the Computer Running ............................................. 1-2 Unpacking ........................................................................... 1-2 Connecting to AC Power .................................................... 1-3 Opening and Closing the Cover ........................................ 1-4 Operating in Tablet Mode .................................................
Fn Key .................................................................................. 2-4 Hot Keys .............................................................................. 2-4 Using the Touchpad ................................................................ 2-6 Configuring the Touchpad................................................. 2-8 Navigating on the Screen ....................................................... 2-9 Using the Touchscreen .....................................................
Chapter 4 Expanding Your Computer ........................................... 4-1 Connecting an External Monitor ........................................... 4-2 Connecting a Serial Device ..................................................... 4-3 Connecting a USB Device ....................................................... 4-4 Connecting an IEEE 1394 Device ............................................ 4-5 Connecting Audio Devices .....................................................
Ignition Tab ....................................................................... 6-18 Monitoring Tab ................................................................. 6-19 GPS Status Tab .................................................................. 6-21 Using Getac Camera.............................................................. 6-22 Taking Pictures .................................................................. 6-24 Using View Mode ...........................................................
WLAN Problems .................................................................. 8-9 Other Problems ................................................................. 8-11 Resetting the Computer ....................................................... 8-12 Appendix A Specifications ............................................................... A-1 Appendix B Regulatory Information .............................................. B-1 On the Use of the System .....................................................
Chapter 1 Getting Started Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and running. Then, you will find a section briefly introducing the external components of the computer.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: Notebook computer Accessories: − AC adapter − AC power cord − Shoulder strap − Handgrip strap − Stylus and tether − Digitizer pen (option) − Driver disc − Documents Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
Connecting to AC Power The computer operates either on the external AC power or internal battery power. It is suggested that you use AC power when you start up the computer for the very first time. CAUTION: Use only the AC adapter included with your computer. Using other AC adapters may damage the computer. 1. Plug the DC cord of the AC adapter to the power connector of the computer (). 2. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet (). 3.
NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening and Closing the Cover Open the top cover by pulling up on latch A and releasing latch B () and lifting up the cover (). You can tilt the cover forward or backward for optimal viewing clarity.
Close the top cover by closing the display (). Then position latch B on the display side and bring latch A down () to fix the display in place.
Operating in Tablet Mode In addition to being used as a regular notebook computer (Laptop mode), your computer can also be operated in Tablet mode. In Tablet mode, you operate the computer with a stylus or digitizer pen, or a fingertip, instead of a keyboard or mouse. 1. Open the top cover so that it is almost perpendicular with the keyboard of the computer. 2. Turn the display counter-clockwise by 165o. CAUTION: Do not rotate the display more than 165o, or attempt to rotate the display clockwise. 3.
4. Position the latch B on the display side, then bring latch A down () to fix the display in place. Latch B Latch A In Tablet mode, the computer can be operated while holding it as shown. A handgrip strap is supplied to help you hold the computer. (See “Attaching the Handgrip Strap” in this chapter for installation instructions.
Turning On and Off the Computer Turning On Press the power button ( ). Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off When you finish a working session, you can stop the system by turning off the power or leaving it in Sleep or Hibernation mode: To... Do this... Power off (Shutdown) Use the Windows Start menu in the lower left and follow the shutdown procedure. Sleep Press the power button*.
Taking a Look at the Computer NOTE: Depending on the model you purchased, the appearance of your computer may not be exactly the same as those shown in this manual. CAUTION: You need to open the protective covers to access the connectors or devices inside. When not accessing a connector or device, make sure to close the cover completely for water-, dust-, and fire-proof integrity of your computer. (Engage the locking mechanism if existing.
Ref Component Description See Also CAUTION: To prevent burns to your fingers if using the computer (especially in Tablet Mode) with sunlight-readable mode turned on, do wear gloves when touching the top portion of the LCD display as it may be hot to the touch. P2 Button Can be re-defined using the Button Manager utility. RF Button Serves as the master on/off control of the RF radio. P3 Button Can be re-defined using the Button Manager utility.
Rear Components Ref Component Description See Also Mini IEEE 1394 Port Connects an IEEE 1394 device such as a scanner, printer, DVCAM, and VCR. P. 4-5 Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device. P. 4-6 Microphone Connector Connects an external microphone. P. 4-6 Kensington Lock Locks the computer to a stationary object for security. P. 7-3 VGA Connector Connects an external display monitor.
Right-Side Components Ref Component Stylus Description Serves as the input device by tapping on the touchscreen to make selections and enter information. See Also P. 2-9 NOTE: Some models do not have the stylus slot on the right side, so you can only use the slot on the left side for storing the stylus. Tether Hole Stylus can be tethered to this hole. P. 1-16 NOTE: Depending on your model, this is on both sides of the computer or on the left side only.
Left-Side Components Ref Component Description See Also Tether Hole Stylus can be tethered to this hole. Stylus Slot Stylus can be stored in this slot. Power Connector Connects the AC adapter. P. 1-3 USB Port Connects a USB device, such as a flash disk, printer, digital camera, joystick, and more. P. 4-4 RJ-11 Connector Connects the telephone line. P. 2-17 RJ-45 Connector Connects the LAN cable. P.
Ref Component SD Card Reader Description Accepts an SD/SDHC/SDXC card for removable storage media. See Also P. 4-12 Top-open Components Ref Component Camera Lens Allows you to use your computer’s camera function. The lens supports 2 MP (mega pixel). It can be rotated. Touchscreen Displays and receives information for the computer. 1-14 Getting Started Description See Also P. 6-22 P.
Ref Component Description See Also Light Sensor Detects the surrounding lighting condition for automatic adjustment of the LCD brightness and optional keyboard backlight. Fingerprint Scanner (optional) Uses fingerprint verification to protect your computer against unauthorized access. Keyboard Serves as the data input device. P. 2-2 Touchpad Serves as the pointing device. P. 2-6 Indicators Show the current status of the computer’s devices. AC Power Battery Charge P.
Bottom Components Ref Component Strap Holder Four bottom hooks hold the handgrip strap. Docking Connector Inside is the docking connector for connecting an office dock or vehicle dock (purchased separately). Memory Slots Inside are the memory slots for expanding the memory size of your computer. P. 4-13 SIM Card Slot (optional) Inside is the SIM card slot. P. 2-23 1-16 Getting Started Description See Also P.
Using Accessories Using the Tether A tether is provided for attaching the stylus to your computer. 1. Insert one of the tether’s loop ends through the hole of the stylus (as indicated by below). Then, insert the other end through the first loop (as indicated by below) and pull it tight. 2. Insert the other loop end to the tether hole on the computer (as indicated by below). Then, insert the stylus end through the loop (as indicated by below) and pull it tight.
Attaching the Handgrip Strap To use the handgrip strap, attach its four loops to the four bottom hooks on your computer. Make sure the loops are securely hooked. When you need to operate and hold your computer at the same time, insert your hand through the strap for a firm grip. Attaching the Shoulder Strap To use the shoulder strap, secure the snap hooks to the two buckles on your computer.
CAUTION: The strap has been designed to carry only the weight of the computer. Therefore, be sure that the strap does not carry a weight that exceeds the weight of the computer. The strap may accidentally come loose from the computer. Do not use a strap that is damaged or about to tear.
Chapter 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user, you may choose to read only the parts containing information unique to your computer. CAUTION: Do not expose your skin to the computer when operating it in a very hot or cold environment. The computer can get uncomfortably warm when you use it in high temperatures.
Using the Internal Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off.
Function Keys On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs. Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key.
Key Description Decreases the LCD brightness (20 levels). Increases the LCD brightness (20 levels). Switches the system sound output off (mute) and on. Switches LCD backlight on and off. Switches the display output when external devices are connected. Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.) Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Double-click Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vice versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, go to Control Panel Mouse Properties.
Navigating on the Screen The screen of your computer is touch-sensitive. You can control the location of the cursor/pointer on the screen using your finger or the included stylus or digitizer pen to communicate with the computer. CAUTION: Do not use sharp objects on the LCD display. Doing so may damage the display surface. Use your finger or the included stylus or digitizer pen.
Equivalent Mouse Function Term/Action Tap and hold: Tap and hold until a popup menu appears. Right-click Drag: Hold the stylus (or finger) on the screen and drag across the screen until reaching your destination. Drag Using Multi-touch Gestures If your computer model comes with multi-touch-capable screen and Windows 7, you can interact with your computer by placing two fingers on the screen. The movement of the fingers across the screen creates “gestures,” which send commands to the computer.
Gestures ( Actions = finger down; = finger up) Rotate or Move two fingers in opposing directions. -orUse one finger to pivot around another. Press and Tap Descriptions Use rotating to move a picture or other item on the screen in a circular direction (clockwise or counterclockwise). The gesture works in applications that support the specific gesture. Use press and tap to access the shortcut menu. Press on target and tap using a second finger.
Gestures ( Actions = finger down; = finger up) Flicks Make quick drag gestures in the desired direction. Descriptions Flick left or right to navigate back and forward in a browser and other applications. The gesture works in most applications that support back and forward. Using the Dual Mode Display (Optional) Dual mode display incorporates both touchscreen and digitizer functions. The display is set to Touchscreen mode by default.
Term Action Move Move the cursor pointed by the digitizer pen. Click/Point Tap gently on the display. Double-click Tap twice on the display rapidly. Drag and drop Tap lightly on the display and move your digitizer pen until you reach your destination (drag). Finally, release your digitizer pen (drop) when you finish dragging your selection to the destination. The object will drop into the new location. Right-click Press and hold down the digitizer pen button (A), then tap gently the object.
The active digitizer feature cannot be used in the BIOS Setup program or when using the full screen in DOS mode. NOTE: You can move the cursor by bringing the digitizer pen close to the screen, without actually touching the screen’s surface. Do not move the digitizer pen too quickly. If the pen moves too quickly, the cursor may be unable to follow its movement. If you cannot click on the edge of the screen, hold the digitizer pen perpendicular to the display and try clicking again.
For a Model with WWAN Module Primary Landscape Secondary Landscape Primary Landscape Display Display Display NOTE: If the screen display resolution has been set to 800×600 pixels, you can rotate the display to Primary Landscape and Secondary Landscape only. While the display is rotated: – Do not set the display resolution larger than the resolution of the LCD display.
Using the Input Panel You can use the Input Panel to enter text and perform various keyboard functions. There are two types of Input Panels for you to use in Windows 7: Touch Keyboard allows you to enter text by tapping the keys with your stylus, like pressing the keys on a standard keyboard. Writing Pad allows you to write on the writing pad, like writing on a piece of paper. Your handwriting will be converted into typed text.
Using the Network Features Using the Modem The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line. NOTE: When using the communication software, you may have to disable power management.
Using the LAN The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub. Using the Wireless LAN The WLAN module of your computer supports IEEE 802.11a/g/n.
For body worn operation, this device has been tested and meets FCC RF exposure guidelines when positioned at 0 cm from the body. SAR (Specific Absorption Rate) of the WLAN transmitter is 0.376W/kg (1g). Your computer has a built-in Fn+F2 WLAN hot key to switch the WLAN on/off. If you need to temporarily turn off the radio, press Fn+F2. To resume network connection, press Fn+F2 again. NOTE: Fn+F2 hot key works only when RF is set to ON in the OSD Control Panel.
4. Some networks require a network security key or passphrase. To connect to one of those networks, ask your network administrator or Internet service provider (ISP) for the security key or passphrase. For more information on setting a wireless network connection, refer to Windows online help. NOTE: You can use Intel® PROSet Wireless to take full advantage of the WiFi capabilities of your computer. See the Help of the utility for instructions.
Using the Bluetooth Feature Depending on your model, your computer may incorporate the Bluetooth 4.0 capability for short-range (about 50 meters) wireless communications between devices without requiring a cable connection. With Bluetooth, data can be transmitted through walls, pockets and briefcases as long as two devices are within range. Turning Off/On the Bluetooth Radio To turn on or off the wireless radio (including the Bluetooth radio), press the button located on the front of your computer.
4. Select the device you want to connect from the search results. 5. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. For detailed information on using the Bluetooth feature, see Windows’ online Help.
Using the WWAN Feature (Optional) A WWAN (Wireless Wide Area Network) uses mobile telecommunication cellular network technologies to transfer data. The WWAN module of your computer supports 3G or 4G LTE depending on your model. NOTE: Your computer only supports data transmission; voice transmission is not supported. Installing a SIM Card To use the WWAN feature to connect to the Internet, you need to subscribe to the service and acquire a SIM card from a mobile phone network service provider.
4. Locate the SIM card slot. Slide the locking tab inward to unlock. 5. Lift the slot up and, noting the orientation, insert the SIM card into the slot. Locking tab 6. Slide the locking tab outward to secure the SIM card in place. 7. Close the compartment cover and secure with four screws. Turning Off/On the WWAN Radio NOTE: For body worn operation, this device has been tested and meets FCC RF exposure guidelines when positioned at 0 cm from the body.
Connecting to WWAN Network 1. Make sure that the SIM card is inserted and WWAN function is enabled (as described above). 2. On Windows desktop, double-click the AirCard Watcher shortcut. The screen as below appears. 3. If the radio is currently off, click Turn Radio On to turn on the radio. 4.
Using the Fingerprint Scanner (Optional) CAUTION: We shall not be liable for any loss or damage whatsoever resulting from your use of the fingerprint scanner or neglect of fingerprint scanner use, or any data loss resulting from such developments as fingerprint authentication malfunctioning. It is not recommended that you use the fingerprint scanner in a below-freezing temperature. The moisture on your finger can freeze to the scanner’s metal surface when you touch it, resulting in a failed operation.
You can then use the Fingerprint Software to set up how the fingerprint authentication works. Settings App Store Options Help For detailed information, click the Help button of the software.
Chapter 3 Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer. Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging.
Switch The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green. Replacing the Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack.
4. Pull the ribbon strip to remove the battery pack. 5. With the strip facing outward, insert the new battery pack all the way into the slot.
6. Close the cover. Make sure the latches are engaged. Battery Low Signals and Actions The battery icon battery. Battery Icon changes appearance to display the current state of the Battery Level Description Discharging The icon shows the charge remaining in 10-percent increments until the charge reaches the low-battery level. Low The battery charge has reached the low-battery level (10% by default). Critically low The battery charge has reached the critical battery level (5% by default).
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When...
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the computer can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shuts down.
Power-Saving Tips Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s operating time by following these suggestions. Enter power saving mode when using battery power. Do not disable automatic power management features. Decrease the LCD brightness to the lowest comfortable level. Shorten the length of time before Windows turn off the display. Many USB devices use power just by being connected.
Chapter 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA connector. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a Serial Device Your computer has one or two serial port (depending on model) for connecting a serial device such as a serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the computer is not turned on 2. Plug the device cable to the serial port on the rear of the computer. 3. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer.
Connecting a USB Device Your computer has two USB 3.0 ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. The USB 3.0 port supports a transfer rate up 5 Gbit/s. To connect a USB device, simply plug the device cable to one of the USB ports.
Connecting an IEEE 1394 Device Your computer has a mini IEEE 1394a port for connecting IEEE 1394 devices that include not only computer peripheral devices such as scanner, printer and high-quality CCD, but also consumer electronic equipment such as DVCAM and VCR. To connect an IEEE 1394 device, prepare an IEEE 1394 cable. Plug the appropriate end of the cable to the computer’s mini IEEE 1394 connector and the other end to the device’s corresponding connector.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. ) can be connected to speakers, Audio Output Connector ( headphones, or earphone set. ) can be connected to an external Microphone Connector ( microphone for recording voice or sound. NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows.
Using ExpressCards Your computer may have an ExpressCard slot. The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard. Typical ExpressCards support a very extensive range of applications including memory, wired and wireless communication cards, and security devices. Shown next are the appearances of ExpressCards for your reference. ExpressCard/54 ExpressCard/34 To insert an ExpressCard: 1. Locate the ExpressCard slot on the left side of the computer.
Eject button 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove an ExpressCard: icon found on the 1. Double-click the Safely Remove Hardware Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the ExpressCard from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
Using PC Cards NOTE: Some PC cards require additional system resources. Before using such PC card, you may have to free other system resources for the PC card. Although some PC cards can be inserted and removed without turning off the computer, you cannot remove or install PC cards during Sleep mode. Your computer may have a PC card slot. The slot supports CardBus specifications. The slots can accommodate a type II card. Typical type II cards are flash memory, SRAM, modem, LAN, and SCSI cards.
To remove a PC card: icon found on the 1. Double-click the Safely Remove Hardware Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
Using Smart Cards (Optional) Your computer may have a smart card reader. With an embedded microcontroller, smart cards have the unique ability to store large amounts of data, carry out their own on-card functions (e.g., encryption and mutual authentication), and interact intelligently with a smart card reader. To insert a smart card: 1. Locate the smart card slot. 2. Slide the smart card, with its label and embedded computer chip facing up into the slot. 3.
Using SD Cards NOTE: You can use only storage cards. Your SD card reader does not support cards with I/O (input/output) functions such as a wireless network card or Bluetooth card. Your computer has an SD card reader. The card reader is a small drive for reading from and writing to removable storage cards (or called memory cards). The card reader supports SD (Secure Digital), SDHC (Secure Digital High Capacity), and SDXC (Secure Digital eXtended Capacity) cards. To insert a storage card: 1.
System Memory Upgrade You can upgrade your computer by expanding system memory. CAUTION: It is not recommended that you buy and install RAM modules by yourself. If you want to expand system memory, please ask Getac service center to install DRAM modules for you so that full compatibility can be guaranteed. RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules.
4. To install the RAM module, match the module's notched part with the socket's projected part and firmly insert the module into the socket at a 20-degree angle. Then push down until the retaining clips lock the module into position. CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force it. Check once more to ensure that the module is positioned correctly. 5. Close the compartment cover and secure with four screws.
Chapter 5 Using BIOS Setup and System Recovery BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features.
BIOS Setup When and How to Use You need to run BIOS Setup Utility when: You see an error message on the screen requesting you to run BIOS Setup Utility. You want to restore the factory default BIOS settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize the system performance. To run BIOS Setup Utility, press the F2 key when the prompt appears on the screen during system startup.
In general, you can use the arrow keys to move around and + / – keys to change the setup values. Keyboard information can be found at the bottom of the screen. NOTE: The BIOS Setup Utility screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ. The BIOS Setup Utility program may have been updated after the publication of this manual. The settings you select in your operating system might override similar settings in BIOS Setup Utility.
Main Menu The Main menu contains various system settings. Information Main Advanced Security Boot Exit Item Specific Help System Date: System Time: [05/28/2012] 05 [11:33:08] Legacy USB Support: [Enabled] F1 Help Esc Exit ↑↓ Select Item ←→ Select Menu View or set system date. +/Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit System Time sets the system time. System Date sets the system date.
Advanced Menu The Advanced menu contains advanced settings. Information Main Advanced Security Boot Exit Item Specific Help Wake Up Capability System Policy AC Initiation: SATA Mode: 2.4GHz RF Booster Signal Level AMT Configuration Virtualization Technology Setup Graphic Setup Device Configuration Serial COM Port Configuration F1 Help Esc Exit ↑↓ Select Item ←→ Select Menu [Performance] Events for waking up [Disabled] system from S3 (Sleep) [AHCI] state.
Ring Wake Up From S3 allows a modem device activity to wake up the system from S3 (Sleep) state. USB Wake Up From S3 allows a USB device activity to wake up the system from S3 (Sleep) state. Wake on PCH LAN allows a LAN activity to wake up the system from S3 (Sleep) state. System Policy sets if the system always runs at full speed (Performance) or lowers down when its temperature is too high (Balance). AC Initiation sets if connecting AC power will automatically start or resume your computer.
Intel AMT enables or disables Intel® Active Management Technology BIOS extension execution. AMT allows the system administrator to access an AMT featured computer remotely. Intel AMT Setup Prompt determines whether the prompt for entering Intel AMT Setup appears or not during POST. If disabled, users cannot enter Intel AMT Setup. Virtualization Technology Setup sets Virtualization Technology parameters. Press Enter to access the submenu as shown below.
Graphics Setup sets graphics related options. Press Enter to access the submenu as shown below. Advanced Graphic Setup DVMT Pre-Allocated: DVMT Total Gfx Mem: F1 Help Esc Exit ↑↓ Select Item ←→ Select Menu [ 64MB] [256MB] Item Specific Help Select Pre-Allocated Graphics Memory size used by the Internal Graphics Device. This has no effect if external graphics are present.
Device Configuration enables or disables several hardware components. Press Enter to access the submenu as shown below. Advanced Device Configuration Wireless LAN: WWAN: Bluetooth: Media Card Reader: Smart Card Reader: HD Audio: Modem: Fingerprint Scanner: 1394 Port: Touch Screen: GPS: F1 Help Esc Exit Item Specific Help Set WLAN device to enable/disable.
Serial COM Port Configuration enables or disables the serial port. Press Enter to access the submenu as shown below. Advanced COM PORT Configuration Serial COM PORT1 Serial COM PORT2 Serial COM PORT3 F1 Help Esc Exit 5-10 [Enabled] [Enabled] [Enabled] ↑↓ Select Item ←→ Select Menu Item Specific Help This option controls the Onboard COM1 Address. When enabled, COM1 uses address 0x3F8h and IRQ4.
Security Menu The Security menu contains the security settings, which safeguard your system against unauthorized use. Information Main Advanced Security Boot Exit Item Specific Help Supervisor Password Is: User Password Is: Set Supervisor Password: Set User Password: Password on Boot: Cleared Cleared [Enter] Enter [Enter] [Disabled] Set HDD 0 Password: HDD 0 Password: [Enter] Cleared Set or clear the Supervisor account’s password.
typing it again and pressing Enter. You can set the supervisor/user password to be required for starting up the system and/or entering BIOS Setup. Password on Boot enables or disables the entering of password (if existing) for booting up your system. Set HDD 0 Password sets the password for locking the Primary Master hard disk drive. After setting a password, the hard disk drive can only be unlocked by the password no matter where it is installed.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. Information Main Advanced Security TPM State Boot Exit Item Specific Help Boot 1: 2: 3: 4: 5: 6: 7: 8: priority order: SATA ODD: SATA HDD1:LITEONIT LAT-128M3S USB HDD: USB FDD: PCI LAN: IBA GE Slot 00C8 v1365 USB ODD: Other HDD: ESATA HDD: F1 Help Esc Exit ↑↓ Select Item ←→ Select Menu Keys used to view or configure devices: and arrows Select a device. ’+’ and ’-’ moves the device up or down.
Key Function Shift+1 Deactivates/activates the highlighted boot device on the “Boot priority order” list. When a device has been deactivated, an “!” (exclamation) symbol appears beside the item and system will bypass it when detecting boot device during POST. Exit Menu The Exit menu provides ways of exiting BIOS Setup. After finishing with your settings, you must save and exit so that the changes can take effect.
System Recovery Use System Recovery when: Your Windows operating system does not start at all. You want to restore the system to the factory state. WARNING: Using this feature will reinstall Windows to your system and configure it to the system’s factory default settings. All data on the hard disk drive will be lost. Make sure that power is not interrupted during the recovery process. An unsuccessful recovery may result in Windows startup problems. To run System Recovery: 1.
4. The progress bar shows the percentage completed. When it reaches 100%, the system turns off. 5. Turn on the computer. The Windows setup wizard starts. Follow the onscreen prompts to continue. 6. When the system restarts, the installer screen appears. The installer will perform system hardware detection and driver installation. 7. When completed, the system restarts and displays Windows desktop.
Chapter 6 Using Getac Software Getac software includes application programs for specific computer components and utility programs for overall management. This chapter describes how to use the software.
Using the OSD Control Panel The OSD (On Screen Display) Control Panel provides a user-friendly interface for you to quickly activate or operate certain functions on your computer with a simple tap of the screen. To open the OSD Control Panel, press the button computer. on the front of your The following screen appears. The following table shows the various functions on the OSD Control Panel.
Icon Function Opens the Help file explaining the OSD Control Panel. Opens the Quick Button Setup menu (refer to the next section for details). Closes the OSD Control Panel. Serves as the master ON/OFF control of the RF radio. The word on the button indicates the current status. The on/off status will persist through Sleep/Hibernation mode but it will always be on upon restarting. Enables or disables the G-Rotate function.
Icon Function When set to MAX, the backlight is adjusted to the highest brightness level. When set to AUTO, the brightness will be automatically adjusted according to the current ambient light. The backlight will return to the default MANUAL setting whenever the system resumes from Sleep/Hibernation mode or the system is restarted. Switches the display output to the next choice: VGA (external monitor), BOTH (LCD and external monitor), or LCD. This button works only when an external display is connected.
Icon Function Allows you to adjust the sound volume by dragging the knob along the bar. Switches the system sound output OFF (mute) and ON. Allows you to adjust the LCD brightness level by dragging the knob along the bar. System enters “black-out” mode by turning off the LCD display, LED indicators, touchscreen, and sound. Press the power button ( “black-out” mode.
Quick Button Setup By default, the five quick buttons on the OSD Control Panel have pre-assigned functions. You can re-define the buttons: ) on the OSD control panel 1. Click the Quick Button Setup button ( and the Quick Button Setup window appears. 2. At the bottom of the screen are the five quick buttons. Click the button you want to change. 3. Depending on the type of task to be associated with the button, click the Open button of the Executed Program or Open Folder type. 4. A dialog box appears.
or 5. You can change the image appearing on the button by clicking the Select Image button. After selecting the image file, the original image on the button will be replaced. 6. Click Set to complete the changes. NOTE: You can restore the quick buttons to the default settings by clicking Reset All.
Using Button Manager The five quick buttons located on the front of your computer come with predefined functions. You can use Button Manager to re-define the buttons. 1. Click Start Programs Button Manager Button Manager. The following screen appears. 2. Select the button to re-define. 3. Under the Update Button Function click the Key Name dropdown list to see the available options and select the option you want.
The option User Define Button (1 to 5) means the Quick Button in the OSD Control Panel. 4. Repeat the steps for the other buttons that you want to re-define. 5. For the changes to take effect immediately, click Start Flash. 6. If you intend to save the configurations for later retrieval, click SAVE. Select a location, enter a filename, and click Save to save the current configurations as a .bfh file. Click Load the next time you use Button Manager to load any previously saved configurations.
Using G-Manager G-Manager is a unified user interface utility that allows you to manage and configure the following: System Battery ECO (economic mode) Light Sensor Ignition Monitoring Antenna GPS Status Starting G-Manager You can start up G-Manager by any of the following methods: Click Start All Programs Getac Utility G-Manager, or Click and hold the icon located on the taskbar until a ring appears. From the small menu that pops up, click G-Manager.
System Tab The System tab provides system information. To view specific information, select the component from the list on the left side of the screen. The information of the selected component will be displayed on the right side of the screen.
Battery Tab The Battery tab allows you to check the battery status and configure the battery. At most two batteries may be supported. Click Battery 1 or Battery 2 to view the information of each battery (if your model has a second battery). NOTE: When the percentage % Left is less than 10% then the value will be displayed in red. When an abnormal battery condition is detected Battery Status value will be displayed in red.
Charging Mode The lower left portion of the screen allows you to select the charging mode. Normal Mode – The battery will be fully charged. When remaining charge reaches below 95%, then charging will start until it is fully charged. Economy Mode – This mode helps prolong battery life by charging up to 80% of its total capacity only. It is highly recommended if you are using AC power most of the time.
4. Wait till the process is completed. Click Exit when finished. ECO Tab The ECO tab allows you to configure ECO modes (or called power profiles). To put the system into an ECO mode, use the ECO button (one of the buttons in the OSD Control Panel). (See “Using the OSD Control Panel” earlier in this chapter for information.
ECO Information The left portion of the screen lists the available power profiles (Quick, Power Saving, and Work). Each profile is a combination of power settings that results in different power consumptions. To change the settings of a profile, select (highlight) the profile name in the list. Profile Settings The right portion of the screen displays the settings of the current selected profile. You can set up the following items: WWAN, Bluetooth, and WLAN – can be on or off.
Light Sensor Tab The Light Sensor tab allows you configure how the light sensor works. Sensor Mode The left portion of the screen lists the sensor modes: Normal – Light sensor sensitivity is set at normal environment lighting condition. Bright – Light sensor sensitivity is set at bright environment lighting condition (e.g. outdoors). Dark – Light sensor sensitivity is set at dark environment lighting condition (e.g. indoors, storage warehouse, etc.). Click to select a mode.
Environment Illuminance To have the keypad backlight automatically turn on in poor lighting environment, click the checkbox Automatic Keyboard Backlit. Click Apply or OK to save the changes. Antenna Tab The Antenna tab allows you to set if your system will automatically use the external GPS or WWAN antenna when connected to the Docking Station. Select the checkbox(es) accordingly. Click Apply or OK to save the changes.
Ignition Tab The Ignition tab allows you to configure how your system works with the vehicle ignition. Ignition Control When your system is connected to the Vehicle Dock (available as an option), you can have your system derive power from the vehicle and have the on/off of the vehicle ignition turn on/off your system. To enable the feature, select the checkbox Ignition Power On. Click Apply or OK to save the changes.
Monitoring Tab The Monitoring tab allows you to configure the monitoring function of G-Manager. Items to Monitor The left portion of the screen lists the items. Click the checkbox before an item to include it as a monitored component. Click Apply or OK to save the changes. NOTE: Different models have different supported monitoring items; non-supported items cannot be selected (grayed out items).
Monitoring Interval – sets the frequency of updates on the monitoring window (1/3/5/10/30 seconds or 1/5/30 minutes). Click Apply or OK to save the changes. Starting and Stopping the Monitoring To start monitoring, click START Monitor. The monitoring window similar to the one below appears displaying requested information at specified intervals. To stop monitoring, click the Close button at the upper right corner of the monitoring window or click Stop Monitor on the Monitoring tab page of G-Manager.
GPS Status Tab The GPS Status tab shows the GPS status for models having the GPS module. To start GPS positioning, click Start GPS. The screen displays: Ongoing raw data strings in the Message Log section Overhead satellite positions in the Satellite Map section Signal strength of the satellites in the Signal Indicator section When GPS positioning is completed, the Data Summary section shows the GPS information of the current location. To stop GPS positioning, click Stop GPS.
Using Getac Camera Getac Camera is a geo-tagging camera program, which allows you to stamp geographical information on photos as watermarks and embed such information into JPEG files as EXIF 2.2 metadata. NOTE: Getac Camera works with Virtual-GPS (a separate application program). Make sure that Virtual-GPS is installed in your computer. Before starting Getac Camera, close any other program that uses the camera; otherwise, Getac Camera can only provide limited functions.
No. Screen Elements Descriptions Preview/Display Displays the live image in Camera mode and the Window selected image in View mode. Status Display Indicates the use of a feature. GPS Lock in use Front/Bottom camera in use (depending on your model) / Night mode in use Continuous/Timer mode in use / GPS Status Window Control Buttons Minimizes the program window. Control Buttons Perform immediate tasks on the current image.
Taking Pictures 1. Start the Getac Camera program. You will be in Camera Mode. 2. You can use the buttons on the right and left side of the preview window for immediate controls. (See “Camera Controls” for detailed information.) For overall settings, tap information.) . (See “Camera Settings” for detailed 3. Aim the camera lens at your subject. 4. When ready, you can shoot the picture in either of the two methods: 6-24 Method 1: Tap the button.
5. The picture will appear in the middle of the Thumbnail View and be saved to the predefined storage location. Camera Controls Buttons Control Buttons Descriptions Flips the image vertically. Flips the image horizontally. / / Turns on/off GPS lock. The icon in the button shows the current status. GPS lock allows you record the exact location of the object you are shooting instead of where you are using the computer to shoot the picture.
Using View Mode Tap at the bottom of the screen to switch to View mode. While in Camera mode, you can also switch to View mode by either of the two methods: Method 1: Double-tap the thumbnail in the Thumbnail Tray. Method 2: Drag the thumbnail and drop into the preview window. Selecting an Image To scroll through the Thumbnail Tray, drag the tray toward the left or right. To select an image or video, use either of the two methods: Method 1: Double-tap the thumbnail in the Thumbnail Tray.
Image Viewing Controls When you select an image to view, you can perform the following tasks. To Zoom in/out (up to four scales) Via Control Buttons Via Multi-touch Operations / Drag two fingers apart/ towards to zoom in/out. When zoomed in, you can drag to view another portion of the image.
To Via Control Buttons Rotate to the right/left by 90° Via Multi-touch Operations / Drag two fingers in a clockwise/counterclockwise circular motion. View image properties − Adding Notes to an Image 1. Switch to View mode, select the image, and tap 2. In properties view, tap . 3. Type your notes in the entry field. 4. When completed, tap . The first three lines of the notes show on the screen. 6-28 Using Getac Software .
Camera Settings To change camera settings, tap at the bottom of the screen. Along the left of the window are all the setting items. You can drag this area up or down to scroll through the items. The middle of the window displays the current item and setting value. To the right is the adjustment bar where you can tap or drag to change the setting value. All changes (except for Camera Mode) remain effective until you change them again.
Items Name Descriptions Contrast Adjusts the contrast level. The range of levels depends on computer models. to restore to the default level. You can tap Hue Adjusts the hue level. The range of levels depends on computer models. to restore to the default level. You can tap Flicker Sets the frequency to match the local electrical system for flicker free shooting under electric light. Choices are: 60Hz (default) and 50Hz. LED Light Turns On (default) or Off the LED light.
Items Name Descriptions Watermark Turns On (default) or Off the display of watermark in the image. (Turning off does not affect the embedded EXIF 2.2 metadata.) Shutter Sound Turns On (default) or Off the sound played upon photo shooting. Power Saving Sets if power saving works for the program. System The Camera program enters power (default) saving mode according to the settings of Windows’ Power Options. Never The Camera program will not enter power saving mode while the program window is open.
Items Name Time Option Filename Prefix 6-32 Using Getac Software Descriptions Displays the time throughout the program according to one of the two choices: System time zone (default) The time zone setting of the computer is taken into consideration. If the current location is in daylight saving time, the time will be adjusted accordingly. UTC The time is based on Coordinated Universal Time. The default filename prefix is IMG. The complete filename is IMG_xxxxxx.
Chapter 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering areas such as protecting, storing, cleaning, and traveling.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using an Anti-Virus Strategy You can install a virus-detecting program to monitor potential viruses that could damage your files.
Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock. Store the key in a safe place.
Taking Care of the Computer Location Guidelines For optimal performance, use the computer where the recommended temperature is between 0 °C (32 °F) and 55 °C (131 °F) – actual operating temperature depending on product specifications. Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Using the computer in extreme environments for long periods can result in product deterioration and a shortened product life.
The screen surface is easily scratched. Avoid touching it with a sharp object such as a pen or pencil. LCD image sticking occurs when a fixed pattern is displayed on the screen for a prolonged period of time. You can avoid the problem by limiting the amount of static content on the display. It is recommended that you use a screen saver or turn off the display when it is not in use.
To avoid hastening the deterioration of the battery pack thereby prolonging its useful life, minimize the number of times you charge it so as not to frequently increase its internal temperature. Charge the battery pack between 10 °C ~ 30 °C (50 °F ~ 86 °F) temperature range. A higher environment temperature will cause the battery pack’s temperature to rise. Avoid charging the battery pack inside a closed vehicle and in hot weather condition.
incorrect battery level reading. This phenomenon comes from the chemical characteristics of batteries. The appropriate operating temperature for the battery is -10 °C ~ 50 °C (14 °F ~ 122 °F). Touchscreen Guidelines Use the finger or the included touchscreen pen on the display. Using a sharp or metallic object other than your finger or touchscreen pen may cause scratches and damage the display, thereby causing errors. Avoid using excessive force that may cause damage to the display.
When Traveling Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure that the battery pack is fully charged. Make sure that the computer is turned off and the top cover is securely closed. Do not leave objects in between the keyboard and closed display. Disconnect the AC adapter from the computer and take it with you.
Chapter 8 Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the BIOS Setup program.
Solving Common Problems Battery Problems The battery does not charge (Battery Charge indicator does not light amber). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
Display Problems Nothing appears on the screen. During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. The brightness level might be too low. Increase brightness. The display output might be set to an external device. To switch the display back to the LCD, press the Fn+F9 hot key or change the display through the settings in Display Properties. The characters on the screen are dim.
Simultaneous display/multi-display does not work. Make sure that you turn on the external monitor before turning on the computer. Press the Fn+F9 hot key to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device. The device may not be correctly configured in the BIOS Setup program. Run the BIOS Setup program to identify the new type.
Keyboard, Mouse, and Touchpad Problems The keyboard does not respond. Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. Water or liquid is spilt into the keyboard. Immediately turn off the computer and unplug the AC adapter. Then turn the keyboard upside down to drain the liquid out of the keyboard. Make sure to clean up any part of the spill you can get to.
Power Management Problems The computer does not enter Sleep or Hibernation mode automatically. If you have a connection to another computer, the computer does not enter Sleep or Hibernation mode if the connection is actively in use. Make sure that the Sleep or Hibernation time-out is enabled. The computer does not enter Sleep or Hibernation mode immediately. If the computer is performing an operation, it normally waits for the operation to finish.
If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced. Make sure that the volume control is not set too low. Make sure that the computer is not in Sleep mode. If using an external speaker, make sure that the speaker is properly connected. Distorted sound is produced. Make sure that the volume control is not set too high or too low.
AC adapter is connected and the temperature is above an acceptable range, the computer will display messages on the screen informing you of the heating process; in other conditions, the screen is simply blank.) Wait till the heating is finished. However, if external AC power is not available and the remaining battery power is too low for the heating to complete, the computer may not start up.
I cannot connect to another WLAN device. Make sure that the WLAN feature is turned on. Make sure that the SSID setting is the same for every WLAN device in the network. Your computer is not recognizing changes. Restart the computer. Make sure that the IP address or subnet mask setting is correct. I cannot communicate with the computer in the network when Infrastructure mode is configured.
Other Problems The date/time is incorrect. Correct the date and time via the operating system or BIOS Setup program. After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
Appendix A Specifications NOTE: Specifications are subject to change without any prior notice. Parts Specifications ® CPU Intel Ivy Bridge i5-3320M, 2.6G, 35W Chipset Intel® Panther Point QM77 Memory Up to 8 GB, 240-pin × 2, DDRIII 1333MHz SO-DIMM BIOS 8 MB EEPROM, system and VGA BIOS, Plug-and-Play, ACPI 2.0 capability Display Audio Panel 10.
Parts Antenna Specifications Wi-Fi 802.11a/b/g/n + Bluetooth 2.4G 2 internal (pass-through for external antenna – option) WCDMA/HSDPA 2 internal (pass-through for external antenna – option) GPS 1.5G (option) 1 internal Modem Azalia interface, 56 Kbps, ITU V.90 MDC 1.5 internal fax modem LAN IEEE 802.3i 10Base-T, IEEE 802.3u 100Base-T, IEEE 802.3ab 1000Base-T Ethernet Wireless LAN + Bluetooth Intel® Centrino Advanced-N 6235, 802.11 a/b/g/n WLAN booster (option) Blutooth 4.
Parts Specifications Enclosure IP65 (with input/output doors closed) ESD Air discharge: 0~8 KV (included) no error; 9~15 KV allow soft error Contact discharge: 0~6 KV (included) no error; 7~8 KV allow soft error Regulation EMC FCC part 15, subpart B, class B, CE, CCC Safety UL, TUV, TUV/CB, E-mark Green Product Coverage RoHS 6 European union banned materials, EPEAT Other 12 universal GP product banned materials, ENERGY STAR, WEEE Specifications A-3
Appendix B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
FINNISH VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
Connect the adapter to a proper power source. The voltage requirements are found on the product case and/or packaging. Do not use the adapter if the cord becomes damaged. Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. Option ANSI/ISA 12.12.01 & CSA C22.2 No.
Use caution when installing or modifying telephone lines. Avoid using the telephone function (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone function to report a gas leak in the vicinity of the leak. Do not use this product near water, for example near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
On the Use of the RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use: In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20 cm (8 inches) or more from the body of all persons.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “Turning Off the Wireless LAN Radio.
Departments in Which the Wireless LAN Module’s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
User Notification of Take-back Service To Institutional (B2B) Users in United States: Getac believes in providing our institutional customers with easy-to-use solutions to recycle your Getac-brand products for free. Getac understands the institutional customers will likely be recycling multiple items at once and as such. Getac wants to make the recycling process for these larger shipments as streamlined as possible.
