Users Manual

ManualsBrandsGERMID ManualsBaby Accessories5.0 Inch Video Baby Monitor

5.0 Inch Video Baby Monitor

QUICK START GUIDE

Q: Cannot connect to camera.

A: 1. Please ensure the camera is charging.

2. Make sure the camera and the monitor are within the effective distance.

3. Please confirm if the antenna is tightened

Q: The video changed to unclear.

A: 1. Please try to remove the camera near to monitor.

2. Please clear the obstacle between camera and monitor.

Q: The baby monitor has some noise.

A: 1. The camera and monitor may be too close. Move them further apart.

2. Please adjust the angle of the antenna to minimize wireless interference.

Q: How long this monitor can standby?

A: After charged fully, the monitor can standby about 12 hours.

Q: Can I hear my baby’s voice when turn off the screen?

A: Yes. You should turn on VOX, and it will wake up the screen if a loud sound

is detected.

Q: Picture is black and white?

A: The Night Vision Mode will be activated if the camera worked in a dark

environment. Turn on room light can force monitor out of night vision mode.

FAQ

Summary of content (8 pages)

PAGE 1
FAQ Q: Cannot connect to camera. A: 1. Please ensure the camera is charging. 2. Make sure the camera and the monitor are within the effective distance. 3. Please confirm if the antenna is tightened Q: The video changed to unclear. A: 1. Please try to remove the camera near to monitor. 2. Please clear the obstacle between camera and monitor. Q: The baby monitor has some noise. A: 1. The camera and monitor may be too close. Move them further apart. 2.
PAGE 2
WARNING 1. Strangulation Hazard - Children have strangled in cords. Keep this cord out of the reach of children (more than 3 feet away). 2. Never Place the Camera of Cord in or Near Crib or Playpen. Secure the cord at least three feet away from crib or playpen. 3. Never use the transmitter or receiver near water, including near a bathtub, sink, laundry tub, wet basement, etc. 4. Use the Power Adapter(s) provided by us ONLY.
PAGE 3
PACKING LIST GETTING STARTED Step 1: Charge the monitor by connecting the Power Adapter to the monitor and a socket. The monitor takes about 10 hours to be fully charged (Enlarged 6000 mAh battery), and it lasts about 12 hours. BC50 Camera BC50 Monitor Power Adapter x2 QUICK START GUIDE 5.0 Inch Video Babay Monitor Step 2: Connect the Power Adapter to the camera and a socket to power on the camera.
PAGE 4
OVERVIEW 10 11 1. Camera Unit 1 12 4 2 7 5 1. Light indicator 6 2. Menu/Back: Press to enter menu page in the monitoring image or press as a Back button in menu page. 1. Light sensor 5. Antenna interface 3. Lullaby/Confirm: Press to play lullabies in the monitoring image or press as a Confirm button in menu page. 2. IR LED lights 6. Power cable interface 4. Left: Press to pan the camera leftward in the monitoring image or to change your selection leftward in menu page. 3. Lens 7.
PAGE 5
DELETE CAMERAS MENU SETTINGS 1. Press “ Choose ” PAIR THE CAMERA You do not need to pair it again unless the Camera Unit loses its link with the Monitor Unit or pair to a new Camera Unit. If it shows “Lost Link!!!” after turning on the monitor, this is likely due to the far disstance between the monitor and camera, or the unsuccessful factory pairing. Please move the monitor closer to the camera, or manually pair the monitor with the camera following the next section accordingly. 1.
PAGE 6
4 cameras at most can be connected to one monitor. When you have more than 1 Camera Unit paired (For example 4). The following display modes are available. MODE 1: When selects 1 1 2 3 4 MODE 2: When selects or 2 or 3 , CAM1, CAM2, CAM3 can display separately. VOX SETTING The monitor has a voice operated switch, also known as VOX. If you enable this function, it will turn on the screen when the sound over a certain threshold is detected.
PAGE 7
SYSTEM SETTINGS Factory Reset This function is to set System Date & Time, LCD Auto Off, and Factory Reset. 1. Select “Factory Reset“, press ”OK”. 2.Confirm “YES” to reset. System Date & Time 1. Press “ Choose ” “ to enter the menu page. “ and press ”OK”. 2. Select “System Date & Time“ , then press ”OK”.
PAGE 8
BRIGHTNESS SETTING 1. Press “ Choose ” 2. Press ” “ and ” “ to decrease or increase screen brightness. “ to enter the menu page. “ and press ”OK”. VOX VOLUME SETTING 1. Press “ Choose ” 2. Press ” “ and ” “ to decrease or increase system volume. “ to enter the menu page. “ and press ”OK”. VOX TEMPERATURE SETTING You can set a comfort zone, when the indoor temperature is higher or lower than the temperature you set, the monitor will emit a “Bi..Bi” sound to alarm you.