Installation Instruction

2
PREPARATION
1. Shut o the power at the circuit breaker and remove existing
xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary
for installation.
MOUNTING THE SWITCH BOX (Fig. 1)
3. Remove the mounting screw (D) from the xture.
4. Drill holes in the wall aligned with the key holes located in
the back plate, insert the plastic anchor (E).
5. Secure back plate to the junction box using junction box
screws (C), fasten it to the wall using wood screw (H).The side
of the mounting plate marked “GND” must face out.
6. Choose the number of down rods suitable of your applica-
tion.
7. Thread the xture wire through the rods and canopy. Con-
nect the canopy, down rod and xture body. Make sure all
are tightened.
8. Connect the driver input/output wires with junction box
wires as shown in Fig.2, making sure that all wire connectors
(A) (B)are secured. If your outlet box has a green or bare
copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
MOUNT ON JUNCTION BOX (Fig. 2)
9. Place the xture over the mounting plate and secure it with
mounting screws (D).
10. Connect the glass holder and xture body. Make sure all are
tightened.
11. Thread the glass of glass holder. Secure them with Allen
screw (E) using Allen wrench (F).
Fig. 1
A
D
C
B
E
F
G
H
Wire Connector
Plastic Anchor
Mounting Plate
Wood Screw
Junction Box
Ground Wire
Junction Box Screw
Wire Connector
To Fixture
Mounting Screw
Allen Wrench
Swivelling Cover
Lamp Holder
Connector Wire
Allen Screw
Glass Cover
6” Rod
3-12” Rod
Fixture
Short Rod
Short Rod
Short Rod
Short Rod
Long RodLong Rod
A
G
H
C
B
D
E
F
1
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
Allen Screw
Qty: 1 Extra
7MPF030502NI
1/8”-40×3/16
Nickel Plating
A C F FDB E E
G H
INSTALLATION INSTRUCTION
LED PENDANT
Glass